Fluke Calibration CalPower 6331 Bath Manuals

Manuals and User Guides for Fluke Calibration CalPower 6331 Bath. We have 1 Fluke Calibration CalPower 6331 Bath manual available for free PDF download: User Manual

Fluke Calibration CalPower 6331 User Manual

Fluke Calibration CalPower 6331 User Manual (75 pages)

Calibration Bath

Brand: Fluke Calibration | Category: Test Equipment | Size: 2.23 MB

Table of Contents

Table of Contents
3
1 Before You Start

9
- Symbols Used
  9
- Table 1 International Electrical Symbols
  9
- Safety Information
  10
  - Warnings
    10
  - Cautions
    12
- Authorized Service Centers
  13
2 Introduction

15
3 Specifications and Environmental Conditions

16
- Specifications
  16
- Environmental Conditions
  17
4 Quick Start

18
- Unpacking
  18
- Set up
  19
- Figure 1 Stir Baffle Fill Levels
  20
- Power
  21
- Setting the Temperature
  21
5 Installation

23
- Moving or Uncrating the Bath
  23
- Bath Environment
  23
- Tipping Prevention Bracket Installation
  23
- Dry-Out" Period
  25
- Bath Preparation and Filling
  25
- Power
  25
6 Bath Use

27
- General
  27
- Comparison Calibration
  27
- Calibration of Multiple Probes
  28
- Bath Tank and Lid
  30
- Back Panel
  30
  - Fluid Expansion Reservoir
    31
8 General Operation

32
- Heat Transfer Fluid
  32
  - Temperature Range
    32
  - Viscosity
    32
  - Specific Heat
    33
  - Thermal Conductivity
    33
  - Thermal Expansion
    33
  - Electrical Resistivity
    34
  - Fluid Lifetime
    34
  - Safety
    34
  - Cost
    35
  - Commonly Used Fluids
    35
    
    Water
    35
    
    Ethylene Glycol
    35
    
    Mineral Oil
    35
    
    Silicone Oil
    36
  - Fluid Characteristics Charts
    36
    
    Limitations and Disclaimer
    36
    
    About the Chart
    36
    
    Table 2 Table of Bath Fluids
    37
    
    Figure 4 Chart Showing Usable Range of Various Fluids
    38
- Stirring
  39
- Power
  39
- Heater
  39
- Temperature Controller
  40
9 Controller Operation

41
- Bath Temperature
  41
- Reset Cutout
  41
- Figure 5 Controller Operation Flowchart
  42
- Temperature Set-Point
  43
  - Programmable Set-Points
    43
  - Set-Point Value
    44
  - Set-Point Vernier
    44
- Scan
  45
  - Scan Control
    45
  - Scan Rate
    45
- Temperature Scale Units
  46
- Ramp and Soak Program
  47
  - Number of Program Set-Points
    47
  - Set-Points
    47
  - Program Soak Time
    48
  - Program Function Mode
    48
  - Program Control
    49
- Secondary Menu
  49
- Heater Power
  49
- Table 3 Program Mode Setting Actions
  49
- Proportional Band
  50
- Figure 6 Bath Temperature Fluctuation at Various Proportional Band Settings
  51
- Table 4 Proportional Band - Fluid Table
  52
- Cutout
  53
- Controller Configuration
  54
- Probe Parameters
  54
  - Alpha
    55
- Operating Parameters
  55
  - Cutout Reset Mode
    55
  - Boost Heater Mode
    55
- Serial Interface Parameters
  56
  - Baud Rate
    56
  - Sample Period
    57
  - Duplex Mode
    57
  - Linefeed
    57
- IEEE-488 Parameters
  58
  - Address
    58
  - Transmission Termination
    58
- Calibration Parameters
  59
  - Cto
    59
  - CO and CG
    59
  - H and L
    59
10 Digital Communication Interface

60
- Serial Communications
  60
  - Wiring
    60
  - Setup
    60
    
    Figure 7 Serial Communications Cable Wiring
    60
    
    Baud Rate
    61
    
    Duplex Mode
    61
    
    Linefeed
    61
    
    Sample Period
    61
  - Serial Operation
    61
- IEEE-488 Communication (Optional)
  62
  - Setup
    62
    
    Address
    62
    
    Transmission Termination
    62
  - Operation
    62
- Interface Commands
  62
- Table 5 Interface Command Summary
  64
- Table 5 Interface Command Summary Continued
  65
11 Calibration Procedure

67
- Calibration Points
  67
- Measuring the Set-Point Error
  67
- Computing R0 and ALPHA
  68
- Calibration Example
  68
- Figure 8 Calibration Example
  69
12 Maintenance

70
13 Troubleshooting

72
- Comments
  74
  - EMC Directive
    74
    
    Immunity Testing
    74
    
    Emission Testing
    75
  - Low Voltage Directive (Safety)
    75

Advertisement

Advertisement

Related Products

Fluke Calibration Categories

Test Equipment Measuring Instruments Water Pump

Monitor

Power Supply

More Fluke Calibration Manuals