Kemppi FastMig KM 400 MVU Operation Manual
  1. Manuals
  2. Brands
  3. Kemppi Manuals
  4. Welding System
  5. FastMig KM 400 MVU
  6. Operation manual

Kemppi FastMig KM 400 MVU Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

FastMig
KM 400 MVU
EN
Operating manual • English
NO
Bruksanvisning • Norsk

Advertisement

Table of Contents
loading

Related Manuals for Kemppi FastMig KM 400 MVU

Summary of Contents for Kemppi FastMig KM 400 MVU

  • Page 1 FastMig KM 400 MVU Operating manual • English Bruksanvisning • Norsk...
  • Page 3 OPERATING MANUAL English...

  • Page 4: Table Of Contents

    CONTENTS PREFACE ..................General ............................Introduction ..

  • Page 5: Preface

    This user manual contains important information on the use, maintenance, and safety of your Kemppi product. The technical specifications of the device can be found at the end of the manual. Please read the manual carefully before using the equipment for the first time.

  • Page 6: Introduction

    INTRODUCTION The FastMig KM-series power source 400 is a MIG power source designed for demanding professional use in the three-phase network. The power source has a control panel that allows ready control of the functions of the power source and the wire feeder. Overview of the power source Front view Rear view...

  • Page 7: Installation

    INSTALLATION POSITIONING OF THE MACHINE Place the machine on a firm, dry and level surface. Where possible, do not allow dust or other impurities to enter the machines cooling air flow. Preferably site the machine above floor level; for example on a suitable carriage unit. Notes for positioning the machine • The surface inclination should not exceed 15 degrees.

  • Page 8: Welding And Earthing Cables

    Section 4, ‘Troubleshooting’ . If the failure cannot be eliminated, turn off the machine, and turn it on again. If the failure persists, write down any fault code that may be shown on the display and contact authorised Kemppi service agent.

  • Page 9: Use Of The Control Panel

    USE OF THE CONTROL PANEL The control panel is used for controlling and monitoring the operation of the power source and the wire feeder. The buttons are used for adjusting functions. The displays and indicators reflect the operating modes of the machine. weld data DYNAMICS...

  • Page 10: Adjustment Of Mig Dynamics (Arc Force)

    3.3.4 Adjustment of MIG dynamics (arc force) When you press button 3, you can adjust the MIG welding dynamics of the machine by means of the right-hand knob, 11. The welding dynamics setting affects the properties of the welding arc and the amount of spatter as follows: • The value 0 is the recommended basic setting.

  • Page 11: Setting Of Operation Parameters

    3.3.11 Setting of operation parameters Button 9 also is used for changing welding parameters as follows: • Depress button 9 for at least five seconds. The set-up menu appears on display 2. • Select the parameter to adjust with the left-hand knob (10) so that the name of the parameter you want to adjust is shown on display 2.

  • Page 12: Calibration Of The Wire Feed Speed

    At the same time, the device exits calibration mode and returns to basic operation mode. TROUBLESHOOTING In the event of a failure of the machine, contact an authorised Kemppi service agent. Before taking your unit for servicing, check the list below. OVERLOAD (YELLOW INDICATOR LIT) Two simultaneously operating fans cool the power source.

  • Page 13: Electric Network Overvoltage Or Undervoltage

    ELECTRIC NETWORK OVERVOLTAGE OR UNDERVOLTAGE If the power source is used in an electric network with insufficient voltage (less than 300 V), the control features of the device are disabled automatically. The primary circuits of the power source are protected against power spikes. The product’s mains voltage range is broad enough to prevent overvoltage problems at up to 440 V (see Section 8, ‘Technical specifications’).

  • Page 14: Service

    Other error codes: The machine can show codes not listed here. In the event of an unlisted code appearing, contact an authorised Kemppi service agent and report the error code shown. SERVICE The utilisation level of the power source and its working environment should be taken into consideration in planning the frequency of maintenance of the machine.

  • Page 15: Disposal Of The Machine

    The owner of the equipment is obliged to deliver a decommissioned unit to a regional collection centre, per the instructions of local authorities or a Kemppi representative. By applying this European Directive you will improve the environment and human health.

  • Page 16: Warranty Policy

    The proof must indicate the date of purchase and the manufacturing number of the unit to be repaired. The parts replaced under the terms of this warranty remain the property of Kemppi and must be returned to Kemppi if requested.
  • Page 18 Telefax +358 3 734 8398 FRANCE e-mail: myynti.fi @kemppi.com Tel +33 1 30 90 04 40 KEMPPI, TRADING (BEIJING) COMPANY, LIMITED Telefax +33 1 30 90 04 45 KEMPPI SVERIGE AB Room 420, 3 Zone, Building B, e-mail: sales.fr@kemppi.com Box 717 No.12 Hongda North Street,...

Table of Contents