SOLE E95 Owner's Manual page 11

ASSEMBLY INSTRUCTIONS
3
UPPER HANDLE BAR ARMS
1. Connect the Swing Arm (L-10) to the left Lower arm (13) and
connect the Swing Arm (R-11) to the right Lower arm (14) , and
secure them with six Hex Head Bolts (206), eight Flat Washers
(164), four Curved Washers (181) and six Nyloc Nuts (157) using
the 13/14mm Wrench (184) and 12/14mm Wrench
2. Connect the two wires (L-61 to 62 & R-60 to 62) on the L & R
1 8 7 1 8 7 1 8 7 1 8 7
( ) .
sides together and store the excess wire, including plastic
connectors, back inside the con- sole mast (12). Place the rubber
grommets (75) over the wire on each side and snap them into the
holes of the console mast.
4
UPPER HANDLE BAR ARMS
Use either screw driver (185 or 186) to secure the following plastic parts.
1. Match up the console covers (196 & 197) and secure with three
Phillips Head Screws (139) and two sheet metal screws (142).
2. Match up the Inner Connecting Arm Covers (111 & 112). Install the
covers with two Sheet Metal Screws (142) and two Phillips Head
Screws (139) to each joint.
3. Match up the outer Connecting Arm Covers (109 & 110) and install
onto the Left and Right Connecting Arms (8&9). Secure each side
with a Phillips Head Screw (139) and two Sheet Metal Screws (142).
Make sure you position the covers with the arrows pointing up. If
they are installed incorrectly, they will break.
4. Install Sliding Wheel Covers (104) on each side and secure with four
Phillips Head Screws (139).
5. Install the two Stabilizer Covers (117 & 118) on the middle stabilizer
bar with two Phillips Head Screws (139).
6. Install the Front Stabilizer Cover (103) on the front stabilizer with two
Phillips Head Screws (139).
7. Install the two incline Cover brackets (25), with the hole for mounting
the plastic cover on the bent tab facing rearward, and secure them
on the Incline Rail Assembly (2) with four Phillips Head Screws (145).
Install the Rear incline bar cover (115) on the rail base with two
Screws (139).
8. Install the Rear Stabilizer Cover (116) on the Rear Stabilizer with
four Phillips Head Screws (139).
9. Mate the Front Handle Bar Cover (L-105) and the Rear Handle Bar
Cover (L-106) together on the Left Arm and secure with four Sheet
Metal Screws (142)using the Phillips Head Screw Driver (186).
Repeat the same procedure for #'s107 & 108 on the right side.
10. This step to be performed after the elliptical power is plugged in.
Elevate the incline to Level 8 and install the incline Rail front cover
(113) up against the middle stabilizer tube with four Phillips Head
Screws (139).
11
HARDWARE STEP 3
#75. Switch Wire Cap
(2 pcs)
#157. 3/8" x 7T
Nyloc Nut (6 pcs)
#164. 3/8" x 19 x 1.5T
Flat Washer (8 pcs)
#181. 3/8" x 23 x 2T
Curved Washer (4 pcs)
#206. 3/8" x 2-1/4" Hex
Head Bolt (6 pcs)
HARDWARE STEP 4
#139. M5 x 15mm
Phillips Head Screw
(29 pcs)
#142. Ø 3.5 x 12mm Sheet
Metal Screw (18 pcs)
#145. M6 x 10mm
Phillips Head Screw
(4 pcs)