SOLE E25 Owner's Manual
  1. Manuals
  2. Brands
  3. SOLE Manuals
  4. Elliptical Trainer
  5. E25
  6. Owner's manual

SOLE E25 Owner's Manual

Hide thumbs Also See for E25:
Table of Contents

Advertisement

Quick Links

FmTNESS
0 WNER'S MA NUA L
PLEASE
CAREFULLY
READ THIS ENTIRE MANUAL
BEFORE
OPERA TING YOUR NEW ELLIPTICAL!

Advertisement

Table of Contents
loading

Related Manuals for SOLE E25

Summary of Contents for SOLE E25

  • Page 1 FmTNESS 0 WNER'S MA NUA L PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERA TING YOUR NEW ELLIPTICAL!
  • Page 2 E35 Assembly Instructions ................Operation of Your New Elliptical ................ Maintenance ....................Manufacturer's Limited Warranty ............... ATTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL ONLYAND IS WARRANTED FOR THATAPPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY. E25 / E35 Elliptical...
  • Page 3 ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SOLE FAMILW Thank you for your purchase of this quality elliptical trainer from SOLE. Your new elliptical has been manufactured by one of the leading fitness manufacturers in the world and is...
  • Page 4 • Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue. SAVE THESE INSTRUCTIONS - THINK SAFETY! E25 / E35 Elliptical...

  • Page 5: Grounding

    Whenever the adapter is used, it must be held in place by a metal screw. Adapter Grounded Outlet Tab of Screw Grounding Screw Grounded Outlet Box Grounding Pin E25 / E35 Elliptical...
  • Page 6 SOLE dealer. POWER CONNECTOR LOCATED FRONT, LEFT HAND SIDE OF UNIT. [Transportation] The elliptical is equipped with two transport wheels which are engaged when rear of the Elliptical is lifted. E25 / E35 Elliptical...

  • Page 7: Assembly Pack Check List

    5/16" x 1.5T #151. ku 5/16" Hex Head Bolt (2pcs) Split Washer (4pcs) Star Washer (4pcs) #108.5/16" x 2-1/4" #107.3/8" x 1-1/2" Hex Head Bolt (4 pcs) Hex Head Bolt (2pcs) #101.3/8" x 2-1/4" Hex Head Bolt (1pc) E25 / E35 Elliptical...
  • Page 8 Hex Head Bolt (2 pcs) Flat Washer (2 pcs) Nylon Nut (2 pcs) #125. M6 x 10mm #115. M5 x 15mm #126. ku3.5 x 12mm Phillips Head Screw (4 pcs) Phillips Head Screw (20 pcs) Sheet Metal Screw (2pcs) E25 / E35 Elliptical...
  • Page 9 #161. Phillips Screw Driver (1 pc) #160. Short Screw Driver (1 pc) #162.12/14 mm Wrench (1 pc) #159. 13/14mm Wrench (1pc) E25 / E35 Elliptical...

  • Page 10: Incline Rail Assembly/Console Mast

    Plug all of the connectors into the back of the console; Computer Cable (47), two Hand pulse Cables (52) and Resistance switch wires (55). Secure the Console (46) on the console mounting plate with four M5xl0m/m Phillips Head Screws (117). E25 / E35 Elliptical...
  • Page 11 101 .._. E25 / E35 Elliptical...
  • Page 12 Install the Front Handle Bar Covers (83 left, 85 right) and Rear Handle Bar Covers (84 left, 86 right) over the Handle Bar axle connections with the six 3.5x12m/m screws (126). //' / 1,00 E25 I E35 Elliptical...
  • Page 13 Handle Bar (10&11). The rod end should be on the inside of the Handle Bar bracket. Secure with a 5/16"x1-1/4" Hex Head bolt (109), 5/16" x 20mm Flat Washer (151) and 5/16" Nylon Nut (137) by using 13/14 mm Wrench (159) and 12/14 mm Wrench (162). 162= E25 / E35 Elliptical...
  • Page 14 7. This step to be performed after the elliptical power is plugged in. Run the incline to position 8 and install the incline Rail Front Cover (89) up against the Middle Stabilizer tube with two M5x15mm Phillips Head Screws (115). E25 / E35 Elliptical...
  • Page 15 115126 |N 15 11,5 115115" l...
  • Page 16 5/16"x 1.5T #183. ku5/16" Hex Head Bolt (2pcs) Split Washer (4pcs) Star Washer (4pcs) #135.5/16" x 2-1/4" #133.3/8" x 1-1/2" Hex Head Bolt (4 pcs) Hex Head Bolt (2pcs) #125.3/8" x 2-1/4" Hex Head Bolt (1pc) E25 / E35 Elliptical...
  • Page 17 Hex Head Bolt (2 pcs) Flat Washer (2 pcs) Nylon Nut (2 pcs) #145. M6 x 10m/m #139. M5 x 15m/m #142. qJ3.5x12m/m Phillips Head Screw (4 pcs) Phillips Head Screw (24pcs) Sheet Metal Screw (8pcs) E25 / E35 Elliptical...
  • Page 18 #186. Phillips Screw Driver (1 pc) #185. Short Phillips Screw Driver (1 pc) #184. 13 / 14m/m Wrench (1 pc) #187. 14 m/m Wrench (1 pc) E25 / E35 Elliptical...
  • Page 19 Plug all of the connectors into the back of the console; Computer Cable (50), two Hand pulse Cables (57), Resistance switch wire (60) and Incline switch wire (61). Secure the Console (45) on the console mounting plate with four M5xl0m/m Phillips Head Screws (144). E25 / E35 Elliptical...
  • Page 20 E25 / E35 Elliptical...

  • Page 21: Handlebar Assembly

    Front Handle Bar Covers (105 left, 107 right) and Rear Handle Bar Covers (106 left, 108 right) over the Handle Bar axle connections and secure with the eight 3.5xl0m/m Sheet Metal Screws (142). 1 .._ / E25 / E35 Elliptical...
  • Page 22 Handle Bar (10&11). The rod end should be on the inside of the Handle Bar bracket. Secure both sides with a 5/16"x1-1/4" Hex Head Bolt (134), 5/16"x20mm Flat Washer (170) and 5/16" Nylon Nut (159) by using 13/14 mm Wrench (184) and 12/14 mm Wrench (187). J 170 E25 / E35 Elliptical...
  • Page 23 7. This step to be performed after the elliptical power is plugged in. Run the incline to position 8 and install the incline Rail front cover (113) up against the middle stabilizer tube with four M5x15mm Phillips Head Screws (139). E25 / E35 Elliptical...
  • Page 24 15_'_ -" "-.."" ..l,,a - ..I/159 14525 15,9 o,.1...

  • Page 25: Features

    (5) degrees and the top position sets the footpads to ten (10) degrees. Ramp incline adjustment Both the E25 & E35 Have an exciting new ramp incline feature that will further increase the variety of your workouts. When the incline is at its lowest position you get a normal elliptical workout.
  • Page 26 Getting familiar with the control panel • E25 Console )eaker play Display view Message window Progl --an power switch Control • E35 Console 3eaker ,play matrix Display view window Program buttons _ power switch Control ke E25 / E35 Elliptical...

  • Page 27: Power Up

    115 VAC and there is a power switch located where the line cord plugs into the unit on the left side near the front. The E25 does not have a power switch. If there is no speed input to the console for 20 minutes the console will go to "Sleep".

  • Page 28: Programming The Console

    Down keys then press enter to continue. Next is the Time. You may adjust the Time and press enter to continue. Now you are finished editing the settings and can begin your workout by pressing the E25 / E35 Elliptical...
  • Page 29 (at the top of the hill). Adjust the level and then press enter. 6. *For E35 only: You can now choose to turn off the incline profile for this program. If you E25 / E35 Elliptical...
  • Page 30 Display key. 11. When the program ends the message window will show a summary of your workout. summary will be displayed for a short time then the console will return to the start-up display. E25 / E35 Elliptical...
  • Page 31 Consult your physician before participating in any exercise program. With all SOLE Heart Rate Control elliptical machines you may use the heart rate monitor feature without using the Heart Rate Control program. This function can be used during manual mode or during any of the nine different programs.
  • Page 32 If you are feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will feel harder. Again, this will show up in your RPE and you will train at the proper level for that day. E25 / E35 Elliptical...
  • Page 33 Normally the transmitter will be oriented so the SOLE logo is right side up. (6) The antenna that picks up your heart rate is very sensitive. If there is an outside noise source, turning the whole machine 90 degrees may de-tune the interference.
  • Page 34 Display key. When the program ends the message window will show a summary of your workout. summary will be displayed for a short time then the console will return to the start-up display E25 / E35 Elliptical...

  • Page 35: Maintenance Menu In Console Software

    If there is a problem with the incline, try running the calibration. Press the Incline up key and the Start key at the same time. Hold them down for 5 seconds and the Incline calibration will start and run automatically. If the problem persists contact service. E25 / E35 Elliptical...
  • Page 36 2. Submit all service requests including serial number, contact information and a brief description of the problem online at www.soletreadmills.com/technical.php?p=service. 3. If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1-866-780-SOLE (7653). If you have a technical...

This manual is also suitable for:

E35

Table of Contents