Table of Contents
Advertisement
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly.
To save gas, turn the pilot off when not using the appliance for a prolonged period of time.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because
some gases are heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by hand,
don't try to repair them; call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control system and any gas control, which has been under water.
1. STOP! Read the safety information above.
Fig 1
. SET ON/OFF SWITCH (1) TO "OFF" POSITION.
•
Wait five (5) minutes to clear out any gas, then smell for gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above on this label. If you don't smell gas, go to the next step.
. AUTOMATIC IGNITION (Fig. 1): Locate the pilot (Fig. 3.) inside of firebox at left hand side.
•
ON/OFF switch (1) in ON position, MAN-knob (2) in ON position; set Flame Adjustment knob (3) to lowest setting ().
•
On the remote control handset, press the OFF button (red dot) and large flame button ( ) simultaneously; a
short acoustic signal confirms the start has begun.
•
Further short acoustic signals indicate the ignition process is in progress.
•
When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the highest setting.
•
Press the small flame button ( ) on the remote control handset to reduce the flame height.
. MANUAL IGNITION (Fig. 2): With the window off, locate the pilot (Fig. 3) inside of firebox at left hand side.
•
ON/OFF switch (1) in ON position, MAN-knob (2) in MAN position.
•
Set Flame Adjustment knob (3) to the lowest setting ().
•
Push down the metallic core (4) with a pen or similar instrument; this will establish the pilot gas flow.
•
Light gas at the pilot (5) with a match.
•
Continue holding down metal core (4) for about 10 seconds; after release, pilot should remain lit.
•
If the pilot will not stay lit after several tries, turn the gas control knob (3) to OFF () and call your local
service technician or gas supplier.
•
Reinstall the window and set the MAN-knob (2) to ON; turn Flame Adjustment knob (3) up () or down ()
manually or use the flame buttons ( )( ) buttons on the remote control handset to adjust the flame height.
1. AUTOMATIC SHUT-OFF (using the remote control handset):
•
Press and hold the small flame button ( ) on the remote control handset to shut-off the main burner gas flow.
•
Press OFF button on remote handset to shut-off the appliance, including pilot flame.
. MANUAL SHUT-OFF (using only the ON/OFF switch (1) located to the right hand side of the valve):
•
Press O the ON/OFF switch (1) to shut-off the appliance, including pilot flame.
0
0
Lighting Instructions
FOR YOUR SAFETY, READ BEFORE LIGHTING
LIGHTING INSTRUCTIONS
Fig 2
TO TURN OFF GAS TO APPLIANCE
5
Fig 3
Advertisement
Table of Contents
