Related Manuals for Evolution Rage-B Stealth 185
Summary of Contents for Evolution Rage-B Stealth 185
- Page 1 STEALTH Original Instructions Instrucciones Originales Instructions Originales Original written in UK English Date Published: 31 / 06 / 2015...
-
Page 2: Table Of Contents
www.evolutionpowertools.com TABLE OF CONTENTS English Page 2 Español Página 22 Français Page 44 INTrOduCTION Guarantee Page 5 Machine Specification Page 6 Labels and Symbols Page 7 Vibration Page 7 Intended use of this Power Tool Page 8 Prohibited use of this Power Tool Page 8 SAFETY PrECAuTIONS Electrical Safety... -
Page 3: Guarantee
In no event shall You can also scan the QR code found on the A4 leaflet with a Smart Phone. This will enable Evolution Power Tools be liable for loss or you to validate your machine’s guarantee damage resulting directly or indirectly from... -
Page 4: Machine Specification
www.evolutionpowertools.com rAGE SPECIFICATIONS MAChINE SPECIFICATIONS METrIC IMPErIAL Motor EU (230-240V ~ 50/60 Hz) 1200W Motor UK (110V ~ 50/60 Hz) 1050W Motor USA (120V ~ 60Hz) 1200W 10.5A No Load Speed 3700min (UK & EU) 3900rpm (USA) Weight 5.4kg 12lbs CuTTING CAPACITIES METrIC IMPErIAL... -
Page 5: Labels And Symbols
Do not operate this machine • The measurement and assessment of if warning and/or instruction labels are human exposure to hand-transmitted missing or damaged. Contact Evolution vibration in the workplace is given in: Power Tools for replacement labels. BS EN ISO 5349-1:2001 and Note: All or some of the following symbols BS EN ISO 5349-2:2002. -
Page 6: Intended Use Of This Power Tool
This product is a Hand Operated Volts Circular Saw and has been designed to be used with special Evolution blades. Only use accessories designed for use in this machine Amperes and/or those recommended specifically by Evolution Power Tools Ltd. -
Page 7: Electrical Safety
www.evolutionpowertools.com (1.14) (2.2) 1) General Power Tool ELECTrICAL SAFETY Safety warnings [work area safety] a) Keep work area clean and well lit. This machine is fitted with the correct moulded plug and mains lead for the Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive designated market. - Page 8 www.evolutionpowertools.com (2.4) 3) General Power Tool Safety (2.5) 4) General Power Tool Safety warnings [Personal Safety]. warnings [Power tool use and care]. a) Do not force the power tool. Use the a) Stay alert, watch what you are doing and use common sense when operating a power correct power tool for your application.
-
Page 9: Additional Safety Instructions
www.evolutionpowertools.com (2.6) 5) General Power Tool (2.8) wArNING: the operation of any power Safety warnings [Service] tool can result in foreign objects being thrown towards your eyes, which could result in a) Have your power tool serviced by a severe eye damage. Before beginning power qualified repair person using only identical tool operation, always wear safety goggles replacement parts. - Page 10 www.evolutionpowertools.com i) Do not use High Speed Steel (HSS) b) If the blades are binding, or when interrupting a cut for any reason, release saw blades. the trigger and hold the saw motionless j) Inspect the machine and the blade before each use.
-
Page 11: Getting Started Unpacking
Be aware of the time it takes for the with this machine the following accessories blade to stop after switch is released. are also available from the Evolution online shop at www.evolutionpowertools.com (3.4) wArNING: If any parts are missing, do or from your local retailer. -
Page 12: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW 1. rEAr hANdLE 2. FrONT hANdLE 3. uPPEr BLAdE GuArd 4. LOwEr BLAdE GuArd 5. SOLE PLATE 6. ChIP EXhAuST POrT... -
Page 13: Assembly And Preparation
Do not alter or modify the mains lead. Fig. 1 (<10.1) INSTALLING/rEMOVING A BLAdE wArNING: Only use genuine Evolution blades which are designed for this machine. Ensure that the maximum speed of the blade is compatible with the machine. Only perform this operation with the machine disconnected from the power supply. - Page 14 www.evolutionpowertools.com Parallel Edge Guide A parallel guide (for help when rip cutting) can be fitted to the sole plate of the machine. The guide arm should be inserted into the rectangular slots found at the front of the sole plate, and slid under the locking thumb screw.
- Page 15 www.evolutionpowertools.com Adjustment of the Cutting Angle • Loosen the Bevel Locking Screw found at the front of the saw (Fig. 6). • Tilt the blade to the required angle (Fig. 7). • Tighten the Bevel Locking Screw securely. Note: An angle scale (0 –...
- Page 16 www.evolutionpowertools.com (10.3) Note: Two (2) line of cut guides (for 0 and 45 CuTTING AdVICE bevel angle only) are positioned on the front edge of the sole plate. wArNING: The operator should wear all relevant PPE (Personal Protection Equipment) • Use both hands to move the saw forwards necessary for the job at hand.
-
Page 17: Maintenance
www.evolutionpowertools.com Excessive sparking may indicate the MAINTENANCE presence of dirt in the motor or worn out carbon brushes. (6.1) Note: Any maintenance must be (>6.2) If this is suspected have the machine carried out with the machine switched off and disconnected from the mains/battery serviced and the brushes replaced by a qualified technician. -
Page 18: Service Parts Diagram
www.evolutionpowertools.com PArTS dIAGrAM... -
Page 19: Declaration Of Conformity
In accordance with EN ISO 17050-1:2004 The manufacturer of the product covered by this declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below. - Page 20 Evolution Power Tools Ltd Evolution Power Tools LLC Evolution Power Tools SAS Venture One 8363 Research Drive 61 Avenue Lafontaine Longacre Close Davenport 33560 Holbrook Industrial Estate Iowa Carbon-Blanc Sheffield 52806 Bordeaux S20 3FR +44 (0)114 251 1022 +1 866-EVO-TOOL...
Need help?
Do you have a question about the Rage-B Stealth 185 and is the answer not in the manual?
Questions and answers