Evolution R185CCSL Instruction Manual
Hide thumbs
Also See for R185CCSL:
- Original instructions manual (61 pages) ,
- Original instructions manual (113 pages) ,
- Instruction manual (21 pages)
Subscribe to Our Youtube Channel
Related Manuals for Evolution R185CCSL
Summary of Contents for Evolution R185CCSL
- Page 1 027-0001B, 027-0002B, 027-0003B, 027-0004B, 027-0006B Original Instructions GB2438285 Original written in UK English Date Published:25/07/2018...
-
Page 2: Table Of Contents
www.evolutionpowertools.com TABLE OF CONTENTS INTRODUCTION Warranty Page 3 Specifications Page 4 Vibration Page 5 Labels and Symbols Page 5 Intended use of this Power Tool Page 6 Prohibited use of this Power Tool Page 6 SAFETY PRECAUTIONS Electrical Safety Page 6 Outdoor Use Page 7 General Power Tool Safety Instructions... -
Page 3: Warranty
Technical Helpline, the number of which can be found on the Evolution Power Tools website. We operate several Helplines throughout our worldwide organization, but Technical help is also available from your supplier. -
Page 4: Specifications
www.evolutionpowertools.com SPECIFICATIONS MACHINE SPECIFICATIONS UK/EU Motor EU (220-240V ~ 50 Hz) 1200W Motor UK (110V ~ 50 Hz) 1200W Motor USA (120V ~ 60 Hz) No Load Speed (min /rpm) 3700 3900 Weight 4.2kg 9.9 lb Dust Port Diameter Ø 30mm Ø... -
Page 5: Vibration
WARNING: Do not operate this machine and fingers closely. If any of the symptoms if warning and/or instruction labels are become evident, seek immediate missing or damaged. Contact Evolution medical advice. Power Tools for replacement labels. • The measurement and assessment of... -
Page 6: Intended Use Of This Power Tool
Symbol Description WARNING: This product is a Hand Operated Volts Circular Saw and has been designed to be used with special Evolution blades. Only use Amperes accessories designed for use in this machine Hertz and/or those recommended specifically by Evolution Power Tools Ltd. -
Page 7: Outdoor Use
www.evolutionpowertools.com OUTDOOR USE Unmodified plugs and matching outlets will (1.13) reduce risk of electric shock. WARNING: For your protection if this tool is to b) Avoid body contact with earthed or be used outdoors it should not be exposed to grounded surfaces, such as pipes, radiators, rain, or used in damp locations. -
Page 8: Health Advice
www.evolutionpowertools.com e) Do not overreach. Keep proper footing and g) Use the power tool, accessories and balance at all times. This enables better control tool bits etc. in accordance with these instructions, taking into account the of the power tool in unexpected situations. f) Dress properly. -
Page 9: Safety Instructions For All Saws
www.evolutionpowertools.com You should always: [Kickback causes and (3.2) related warnings] • Work in a well-ventilated area. • Work with approved safety equipment, such Kickback is a sudden reaction to a pinched, as dust masks that are specially designed to jammed or misaligned saw blade, causing filter microscopic particles. -
Page 10: Additional Safety Instructions For Circular Saws
www.evolutionpowertools.com ADDITIONAL SAFETY e) Blade depth and bevel adjusting locking INSTRUCTIONS levers must be tight and secure before making FOR CIRCULAR SAWS a cut. If the blade adjustment shifts while cutting it may cause binding and kickback. a) Do not use High Speed Steel (HSS) f) Blade depth and bevel adjusting locking saw blades. -
Page 11: Items Supplied
If you are at all unsure about any aspect of the use, care or maintenance of an Evolution product, contact the relevant Evolution helpline where up to date information and... -
Page 12: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW 1. CUT MATERIAL EJECTION PORT 10. DEPTH SCALE 2. THUMB LEVER 11. REAR HANDLE INCORPORATING SAFETY START ON/OFF SWITCH 3. MULTI-MATERIAL TCT BLADE 12. UPPER BLADE GUARD 4. LOWER BLADE GUARD 13. PRECISION ENGINEERED SOLE PLATE 5. PARALLEL EDGE GUIDE 14. -
Page 13: Preparation
(10.1) WARNING: Use only genuine Evolution blades (or those Fig. 1 approved by Evolution Power Tools), which are designed for use in these machines. Ensure that the maximum speed of the blade is compatible with the machine. Only perform this operation with the machine disconnected from the power supply. -
Page 14: Parallel Edge Guide
www.evolutionpowertools.com • Safely store the outer blade flange and associated fixings. • Rotate the lower blade guard up into the upper blade guard using the manual thumb lever. (Fig. 5) • Carefully remove the blade (if fitted) from the machine. •... -
Page 15: Cutting Depth Adjustment
Fig. 11 CUTTING ANGLE (BEVEL) ADJUSTMENT (13) The R185CCSL circular saw has the facility to tilt the blade through (up to) 45 to the left hand side. Bevel cuts are therefore possible. Note: The blade is at the vertical position when the protractor scale reads 0 Fig. -
Page 16: Operating Advice (Pre Operation Checks)
Evolution Power Tools offers the following general advice on safe operational procedures and practices for the consideration of the operator. This advice cannot be exhaustive as Evolution has no influence Fig. 14 on the type of workshops or working environments in which these machines may be used. -
Page 17: Ppe
www.evolutionpowertools.com (15) • The operator should wear all relevant PPE (Personal Protection Equipment) necessary for the task ahead. This could include safety glasses,full face mask, dust masks, safety shoes etc. Note: All CCS series machines are equipped with a cutting line debris blower. -
Page 18: Cutting Advice
www.evolutionpowertools.com CUTTING ADVICE A thumb operated lever is provided on (17) the lower blade guard. With care, a skilled WARNING: The operator must always be operator can retract the blade guard aware of the position and routing of the manually, either partially or fully, allowing power cable. -
Page 19: Maintenance & Adjustments
www.evolutionpowertools.com MAINTENANCE & ADJUSTMENTS (18) CCS series The 0 (blade vertical) position can be adjusted. WARNING: The machine must be disconnected from the mains power supply when attempting this procedure. To check 0 position: • Set the blade to the 0 position with the tilting mechanism against its stop. -
Page 20: General Maintenance & Cleaning
www.evolutionpowertools.com GENERAL MAINTENANCE & CLEANING (20) Note: All maintenance must be carried out with the machine switched off and disconnected from the power supply. • Check that all safety features and guards are operating correctly on a regular basis. Only use this machine if all guards/safety features are fully operational. -
Page 21: Declaration Of Conformity
EC DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: UK: Evolution Power Tools Ltd. Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. FR: Evolution Power Tools SAS. 61 Avenue Lafontaine, 33560, Carbon-Blanc, Bordeaux, France. - Page 22 www.evolutionpowertools.com Notes...
- Page 23 www.evolutionpowertools.com Notes...
- Page 24 Total Tools (Importing) Pty Ltd Evolution Power Tools SAS 20 Thackray Road 61 Avenue Lafontaine Port Melbourne 33560, Carbon-Blanc Vic 3207 Bordeaux T: 03 9261 1900 T: +33 (0)5 57 30 61 89 Evolution Power Tools Ltd Evolution Power Tools LLC...
Need help?
Do you have a question about the R185CCSL and is the answer not in the manual?
Questions and answers