Weighing Function - Kenwood FPM810 series Instruction Manual

weighing function

Your food processor is fitted with a built
in weighing function to allow ingredients
to be weighed straight into the bowl or
blender goblet.
l
The Maximum weighing capacity is 3Kg.
This is the total weight of all the
ingredients including the weight of the
bowl or goblet.
to use the weighing
function
1 Always fit the bowl, detachable drive shaft and attachment or
blender goblet onto the power unit before adding ingredients.
2 Plug in – the display screen will remain blank.
3 Press the ON/ZERO button once and
the display screen will light up.
4 Press the (kg/lb) button to select either
grams or ounces. The display will
default to kg/g when first switched on.
l
The unit weighs in 2g increments and teaspoon/tablespoon
measures are recommended for weighing small quantities.
5 Check the display shows 'O', if not, zero by pressing the
ON/ZERO button. Then weigh the required ingredients straight
into the bowl or goblet. After the weight is displayed, press the
ON/ZERO button and the display will return to 'O'. Add the next
ingredients and that weight will be displayed. Repeat until all
ingredients are weighed.
l
If the display is not zeroed and either the ingredients or the
bowl/attachment/lid are removed the display will show [ - - - -] to
represent a minus reading.
To zero press the ON/ZERO button once.
6 Add the lid and select a speed to operate the processor.
l
During operation the display screen will freeze [- - - -] until the
speed control returned to the 'O' off
position.
l
After processing the last weight will
be displayed on the screen when
the speed control is returned to the
'O' off position. Note: The weight of
the lid will be included if the display
is not zeroed before switching on.
l
The weight of any additional
ingredients added down the feed
tube whilst the processor is running
will not be shown on the display screen.
bp
weighing tray
A removable weighing tray is supplied for weighing ingredients
without the bowl or blender.
To use, place the tray on top of the power unit. Then follow
steps 2 to 5 under 'to use the weighing function'.
To remove, just lift the tray off.
auto switch off
l
The display screen will turn off automatically if the same weight
reading is shown after 5 minutes.
l
The display screen can be turned off manually by pressing and
holding down the ON/ZERO button for a few seconds.
important
l
Do not overload by exceeding the maximum weighing capacity
of 3Kg. The display will show [0 – Ld] if the weighing function is
overloaded.
l
Do not subject the power unit to excessive force as this may
damage the weighing sensor.
l
Always place the processor on a dry flat surface prior to
weighing.
l
Do not move the power unit during operation of the weighing
function.
to use your thermoresist blender
bt
1 Fit the sealing ring
located correctly in the grooved area.
l
Leaking will occur if the seal is damaged or
incorrectly fitted.
2 Hold the underside of the blade unit
into the goblet - turn anti-clockwise until it clicks
graphics on the underside of the blade unit as follows:
- unlocked position
- locked position
The blender will not work if incorrectly assembled.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and push down to secure
cap.
5 Place the blender onto the power unit, and turn clockwise
lock.
l
The appliance will not operate if the blender is
incorrectly fitted to the interlock.
6 Select Auto, or a speed (refer to the recommended speed chart)
or use the pulse control.
hints
l
When making mayonnaise, put all the ingredients, except the oil,
into the blender. Remove the filler cap. Then, with the appliance
running, add the oil slowly through the hole in the lid.
l
Thick mixtures, e.g. pâtés and dips, may need scraping down. If
the mixture is difficult to process, add more liquid.
l
Ice crushing - operate the pulse in short bursts until crushed to the
desired consistency.
l
The processing of spices is not recommended as they may
damage the plastic parts.
l
The appliance will not work if the blender is incorrectly fitted.
l
To blend dry ingredients - cut into pieces, remove the filler cap,
then with the appliance running, drop the pieces down one by
one. Keep your hand over the opening. For best results empty
regularly.
l
Don't use the blender as a storage container. Keep it empty
before and after use.
l
Never blend more than 1.6 litres (2 pts 8 fl oz) - less for frothy
liquids like milkshakes.
6
ck
into the blade unit - ensuring the seal is
ck
and insert the blades
4
. Refer to the
5
. Fit the filler
6
to