Citrus Juicer - Kenwood kMix FPX930 Series Instruction Manual

citrus juicer

Use the citrus juicer to squeeze the juice from citrus fruits
(eg oranges, lemons, limes and grapefruits).
cone
sieve
to use the citrus juicer
1 Fit the drive shaft and bowl onto the power unit.
2 Fit the sieve into the bowl - ensuring the sieve handle is
locked into position directly over the bowl handle
3 Place the cone over the drive shaft turning until it drops all
the way down .
4 Cut the fruit in half. Then switch on and press the fruit onto
the cone.
l
The citrus juicer will not operate if the sieve is
not locked correctly.
l
For best results store and juice the fruit at room temperature
and hand roll on a worktop before juicing.
l
To help with juice extraction move the fruit from side to side
when juicing.
l
When juicing large quantities, empty the strainer regularly to
prevent the build up of pulp and seeds.
mini processor bowl
Use the mini processor bowl to chop herbs and process
small quantities of ingredients e.g. meat, onion, nuts,
mayonnaise, vegetables, purées, sauces and baby food.
mini processor knife blade
mini processor bowl
to use the mini processor bowl
1 Fit the drive shaft and bowl onto the power unit.
2 Fit the mini processor bowl - ensuring the ribs on the inside
of the mini bowl chimney align with the slots in the main
bowl chimney .
3 Place the knife blade over the drive shaft
4 Add the ingredients to be processed.
5 Fit the lid and switch on.
important
l
Do not process spices – they may damage the plastic.
l
Do not process hard food such as coffee beans, ice cubes
or chocolate – they may damage the blade.
hints
l
Herbs are best chopped when clean and dry.
l
Always add a little liquid when blending cooked ingredients
to make baby food.
l
Cut foods such as meat, bread, vegetables into cubes
approximately 1-2 cm ( 1 ⁄
l
When making mayonnaise add the oil down the feed tube.
.
– 3 ⁄ in) before processing.
2 4
metal centrifugal juicer
Use the centrifugal juicer for making juice from firm fruit
and vegetables.
pusher
centrifugal lid
pulp remover
filter drum
juicer drive shaft
to use the centrifugal juicer
.
1 Fit the juicer drive shaft and bowl onto the power unit.
2 Place the pulp remover
the tabs locate with the slots in the bottom of the drum
3 Fit the filter drum
4 Place the attachment lid
locks . Your juicer will not operate if the bowl or
lid are not fitted correctly into the interlock
5 Place a suitable glass or jug under the juice outlet.
6 Cut the food to fit the feed tube.
7 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube. Process fully before
adding more.
l
After adding the last piece, let the juicer run for a further 30
seconds to extract all the juice from the filter drum.
important
l
f the juicer starts to vibrate, switch off and empty the pulp
I
from the drum. (The juicer vibrates if the pulp becomes
unevenly distributed).
l
Maximum capacity that can be processed at one time is
500g of fruit or vegetables.
l
Some very hard foods may make your juicer slow down or
stop. If this happens switch off and unblock the filter.
l
Switch off and clear the pulp collector regularly during use.
hints
l
Before processing remove stones and pips (eg pepper,
melon, plum) and tough skins (eg melon, pineapple). You
don't need to peel or core apples and pears.
l
Use firm, fresh fruit and vegetables.
l
Citrus fruit - peel and remove the white pith, otherwise the
juice may taste bitter. For best results use the citrus juicer.
7
into the filter drum
.
onto the bowl and turn until it
- ensuring
.
.