Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ACME Spider FC
Summary of Contents for ACME Spider FC
- Page 1 LED‐FB8FC User Manual Please read the instruction carefully before use ...
-
Page 2: Table Of Contents
CONTENTS 1. Safety Instructions....................2 2. Technical Specifications ....................3 3. How To Set The Unit ....................4 3.1 Rear Panel......................4 3.2 Main Function ....................5 4. How to Control the Unit ..................10 4.1 Master/Slave Built In Preprogrammed Function ..........11 4.2 Easy Controller....................11 4.3 DMX Controller....................11 5. DMX512 Configuration ...................12 6. DMX Connection ....................16 7. Troubleshooting......................17 8. Fixture Cleaning......................18 ... -
Page 3: Safety Instructions
1. Safety Instructions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING PLEASE keep this User Manual for future consultation. If you sell the fixture to another user, make sure that they also receive this instruction booklet. PLEASE unpack and check carefully there is no transportation damage before using the fixture. It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. PLEASE disconnect main power before servicing and maintenance. Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this. Unit’s surface temperature may reach up to 85℃. DO NOT touch the housing bare‐handed during its operation. ... -
Page 4: Technical Specifications
Caution: There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer. For 230V 50Hz power supply, maximum fixtures that can be connected together from the same mains outlet is 10; For 120V 60Hz power supply, maximum fixtures that can be connected together from the same mains outlet is 6; Installation: The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to ... -
Page 5: How To Set The Unit
Power Voltage: AC 100~240V, 50/60Hz Power Consumption: 66.5 W LED Sources: 8 x 8W Quad‐color(4 in 1) LEDs Weight: 5.5kgs Dimension: ... -
Page 6: Main Function
3. Fuse (T 3.15A): Used to protect the unit from the damage of the over‐current; 4. DMX IN/OUT: For DMX512 links, use 3‐pin XLR plug cable to link the unit together; 5. Only for remote control: Used to connect to the CA‐8 to control the unit for Stand by, Function and Mode function; 6. Microphone: Used to receive music for the sound activation; 7. LED: DMX On DMX input present MASTER On Master Mode SLAVE On Slave Mode SOUND Flashing Sound activation 8. Button: MENU To select the programming functions DOWN ... - Page 7 ...
- Page 8 DMX 512 ADDRESS To select the , press the ENTER button to show the DMX ADDRESS on the display. Use the DOWN/UP button to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. CHANNEL MODE To select the , press the ENTER button to show the DMX CHANNEL MODE on the display. Use the DOWN/UP button to select the 1, 6, 12, 36 channel modes. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. SLAVE MODE To select the , press the ENTER button to show the SLAVE MODE on the display. Use the DOWN/UP button to select the (MASTER), (SLAVE 1), (SLAVE 2) modes. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. SHOW MODE To select the , press the ENTER button to show the SHOW MODE on the display. Use the DOWN/UP button to select the (Random show), ...
- Page 9 SOUND MODE To select the , press the ENTER button to show the SOUND MODE on the display. Use the DOWN/UP button to select the (sound on) or (sound off) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. BLACKOUT MODE To select the , press the ENTER button to show the BALCKOUT MODE on the display. Use the DOWN/UP button to select the (blackout) or (normal) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. LED DISPLAY To select the , press the ENTER button to show the LED DISPLAY on the display. Use the DOWN/UP button to select the (LED on) or (LED off) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. DISPLAY INVERSE To select the ...
- Page 10 DOWN/UP button to select the (tilt 1 inversion) or (normal) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. TILT 2 INVERSE To select the , press the ENTER button to show the TILT 2 INVERSE on the display. Use the DOWN/UP button to select the (tilt 2 inversion) or (normal) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. REV MODE To select the , press the ENTER button to show the REV on the display. Use the DOWN/UP button to select the (the projector lenses will light up right to left) or (normal, the projector lenses will light up right to left) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. AUTO TEST To select the , press the ENTER button to show the TEST on the display and the unit will run ...
-
Page 11: How To Control The Unit
press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. FIXTURE USE HOURS To select the , press the ENTER button to show the FIXTURE USE HOURS on the display and the display will show the number of working hours of the unit . To go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. SOFTWARE VERSION To select the , press the ENTER button to show the SOFTWARE VERSION on the display and the display will show the version of software of the unit . To go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. RESET To select the , press the ENTER button to show the RESET on the display. Press the ENTER button and all channels of the unit will return to their standard position. 4. How to Control the Unit You can operate the unit in three ways: 1. By master/slave built‐in preprogram function 2. By easy controller 3. By DMX controller No need to turn the unit off when you change the DMX address, as new DMX address setting will be affected at once. Each time you turn the unit on, it will show “ ” on the display. After that the unit will be ready to receive DMX signal or run the built in programs. ... -
Page 12: Master/Slave Built In Preprogrammed Function
4.1 Master/Slave Built In Preprogrammed Function By linking the units in master/slave connection, the first unit will control the other units to give an automatic, sound activated, synchronized light show. This function is good when you want an instant show. You have to set the first unit in master mode and select (random show), (show 1) or …or (show 12). Its DMX input jack will have nothing plugged into it, and its master LED will be constantly on and sound LED will flash to the music. The other units will have to select (normal) or (2 light show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave LED lights will be constantly on. 2‐light show In slave mode, means the unit works as the master unit and means 2‐light show. In order to create a great light show, you can set on the second unit to get contrast movement to each other, even if you have two units only. 4.2 Easy Controller The easy remote control is used only in master/slave mode. By connecting to the 1/4” microphone jack of the first unit, you will find that the remote controller on the first unit will control all the other units for Stand by, Function and Mode selection. . Blackout Blackout the unit ... -
Page 13: Dmx512 Configuration
the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press and keep ENTER button pressed up to when the display stops blinking or storing automatically 7 seconds later. To go back to the functions without any change press the MENU button again. Please refer to the following diagram to address your DMX512 channel for the first 4 units. 5. DMX512 Configuration 1/6 Channels Mode: ... - Page 14 12 Channels Mode: ...
- Page 15 36 Channels Mode: ...
- Page 16 ...
-
Page 17: Dmx Connection
6. DMX Connection 1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system 2. The DMX output and input connectors are pass‐through to maintain the DMX circuit when one of the units’ power is disconnected. 3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal errors. Solder a 120‐ohm 1/4W resistor between pin 2(DMX‐) and pin 3(DMX+) into a 3‐pin XLR‐plug and plug it in the DMX‐output of the last fixture. 4. Each lighting fixture needs to have an address set to receive the data sent by the controller. The address number is between 0‐511 (usually 0 & 1 are equal to 1). 5. 3 pin XLR connectors are more popular than 5 pins XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (‐), Pin 3: Positive signal (+) ... -
Page 18: Troubleshooting
7. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. 3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the fixture or the previous one. 4. Try to use another DMX controller. 5. -
Page 19: Fixture Cleaning
8. Fixture Cleaning The cleaning must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: moist, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean the external optics at least every 30 days. Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103‐1: 2009 ; EN55103‐2: 2009; EN62471: 2008; EN61000‐3‐2: 2006 + A1:2009 + A2:2009; EN61000‐3‐3: 2008. & Harmonized Standard EN 60598‐1:2008 + All:2009; EN 60598‐2‐17:1989 + A2:1991; EN 62471:2008; EN 62493: 2010 Safety of household and similar electrical appliances Part 1: General requirements ... - Page 20 Innovation, Quality, Performance ...