Kenmore 29" Installation Instructions Manual page 8

GROUNDING iNSTRUCTiONS
[] For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING-" Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with
the dryer: if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
Explosion Hazard
Use a new CSA International approved gas supply line.
instal[ a shut=off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (330 ram) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Gas type
Natural gas:
This dryer is equipped for use with Natural Gas. It is design-certified by
CSA International for LP (propane or butane) gases with appropriate
conversion.
[]
Your dryer must have the correct burner for the type of gas
in your home. Burner information is located on the rating
plate in the door well of your dryer. If this information does
not agree with the type of gas available, please reference the
"Assistance or Service" section of the "Use and Care Guide".
LP gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the dryer from the gas specified
on the model/serial rating plate for use with a different gas without
consulting the serving gas supplier.
IMPORTANT: The gas installation must conform with local codes, or in the
absence of local codes, with the National Fuel Gas Code, ANSi Z223.1/
NFPA 54 or the Canadian Natural Gas and Propane Installation Code,
CSA B149.1.
Gas supply line
[]
[]
[]
[]
1/2" NPT pipe is recommended.
3/8" approved tubing is acceptable for lengths under 20 ft. (6.1 m) if
local codes and gas supplier permit.
Must include 1/8" NPT minimum plugged tapping accessible for test
gauge connection, immediately upstream of the gas connection to
the dryer (see illustration).
Must include a shutoff valve:
in the U.S.A.:
An individual manual shutoff valve must be installed within
six (6) feet (1.8 m) of the dryer in accordance with the National Fuel
Gas Code, ANSI Z223.1.
in Canada:
An individual manual shutoff valve must be installed in accordance
with the B149.1, Natural Gas and Propane Installation Code. It is
recommended that an individual manual shutoff valve be installed
within six (6) feet (1.8 m)
of the dryer.
The shut off valve location should be easy to reach for opening and
closing.
E
B
A. 3/8" flexible gas connector
B. 3/8" pipe to flare adapter fitting
C. 1/8" NPT minimum plugged tapping
D. 1/2" NPT gas supply line
E. Gas shutoff valve
Gas supply connection requirements
There are many methods by which your gas dryer can be connected to
the gas supply. Listed here are some guidelines
for two different methods of connection.
Option I (Recommended Method)
Flexible stainless steel gas connector:
[]
If local codes permit, use a new flexible stainless steel gas connector
(Design Certified by the American Gas Association or CSA
International) to connect your dryer to the rigid gas supply line. Use
an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the
stainless steel gas connector and the dryer gas pipe, as needed to
prevent kinking.