Advertisement
Table 2. advanced configuraTion: Service MenuS
Some Service Menus may not be available, depending on system type (SM 110).
MENU
FEATURE
100*
Schedule Format
101
Daylight-Saving
Time
110
System Type
120
Fan Control
(heating)
130
Changeover valve
(B/O terminal)
140
Auxiliary Heat
150
Backlight
170
Remote Sensor
180
Heat Pump
Compressor Lockout
190
Heat Pump Auxiliary
Lockout
230
Furnace Filter
Change Reminder
240
Number of Program
Periods
250
Clock format
260
Temperature Format
(°F or °C)
270
Fan Off Delay Heat
280
Fan Off Delay Cool
© COPYRIGHT 2014 PECO ASTRONICS. ALL RIGHTS RESERVED.
OPTIONS
STD. DEFAULT
0-3
1
0,1
0
1-13
1
0,1
0
0,1
0
0,1
0
0,1
0
0-5
0
0-45°F
0
(-18°C - 7°C)
0- 60°F
0
(-18°C - 15°C)
0; 30; 60; 90;
0
120; 365
2; 4 events
4
12 or 24 Hours
12
0,1
1
0-99 Seconds
0
0-99 Seconds
0
DESCRIPTION / COMMENTS
Select the schedule format on the T12000 Series. (Menu not available on non-programmable
thermostats.)
0 =
nonprogrammable
1 =
programmable
2 =
5-1-1 schedule
3 =
5-2 schedule
Select daylight-saving time as it follows standard format in U.S.: It begins second Sunday of
March at 2:00 AM and ends on the first Sunday of November at 2:00 AM.
0 =
Disabled
1 =
Enabled (2007 U.S. Format)
Select the appropriate system configuration (determines available Service Menus).
1 =
1 Heat/1 Cool conventional
2 =
1 Heat/1 Cool heat pump
3 =
Heat only without fan (2-wire systems)
4 =
Heat only with fan
5 =
Cool only
6 =
2 Heat/1 Cool heat pump (with auxiliary heat) and Emergency (Em) heat
7 =
2 Heat/2 Cool multistage conventional
8 =
2 Heat/ 1 Cool multistage conventional
9 =
1 Heat/ 2 Cool multistage conventional
10 = 2 Heat/ 2 Cool heat pump (no auxiliary heat)
11= 3 Heat/ 2 Cool heat pump (with auxiliary heat) and Emergency (Em) heat
12 = 3 Heat/ 1 Cool conventional
13= 3 Heat/ 2 Cool conventional
0 = Fossil Fuel: Gas/Oil/Propane heat (equipment controls heating fan)
1 = Electric Furnace (thermostat controls heating fan)
0 =
B/O terminal controls valve in cooling
1 =
B/O terminal controls valve in heating
0 = Electric backup heat
1 =
Fossil fuel backup heat
0 =
Backlight temporarily on
1 =
Backlight always on (low intensity, 24V only)
Select sensor if used. Contact PECO for information on the T12000 Series Indoor Remote Zone
Sensor.
0 =
No Sensor
1 =
Indoor Sensor
2 =
Outdoor Sensor display only
3 =
Outdoor Sensor display and lockout control
4 =
Indoor, Outdoor Sensor display only
5 =
Indoor, Outdoor Sensor display and lockout control
If an outside sensor is used, the compressor will be locked out when the outside air temp is below
the value selected.
0 = None
15°F( -9°C); 20°F (-7°C); 25°F ( -4°C); 30°F ( -1°C); 35°F (2°C); 40°F (4°C); 45°F (7°C)
If an outside sensor is used, the auxiliary heat will be locked out when the outside air temperature
is above the value selected.
0 = None
40°F (4°C); 45°F (7°C); 50°F (10°C); 55°F (13°C); 60°F (16°C)
Set a filter reminder timer; appears on digital display when timer expires (if programmed).
0 = Off
10 days; 30 days; 60 days; 90 days; 120 days; 365 days
2 =
2 events per day
4 =
4 events per day
12 = 12-hour clock mode
24 = 24-hour clock mode
0 =
Celsius
1 =
Fahrenheit
Select the amount of time (in seconds) that the fan will run after the thermostat heat outputs are
turned off.
Select the amount of time (in seconds) that the fan will run after the thermostat
turned off.
2
cool
outputs are
P/N 70932 3220-2324 REV 00
Advertisement
