Index - Perkins 4.108 Workshop Manual

Index
Aid, Starting - Data
Aid, Starting - To Operate
Air Cleaners N.1
Alternators - Precautions and Maintenance
AC5 Fault Finding
11AC Fault Finding
Testing 15ACR and 17 ACR in Position
Output Test with Regulator Inoperative
Regulator Test
Antifreeze
Approved Service Tools
Atomisers - Data
Atomisers - General and Refitting
Atomisers - Identification
Atomisers - Testing on Engine
Atomisers - Troubles
B.13
C.1
and N.2
0.1
0.1
0.2
0.3
0.4
0.4
C.5
Appendix
B.12
N.10
N.10
N.10
N.10
Batteries C.3
Backlash, Timing Gear - Data B.9
Backlash, Timing Gear Setting and Checking J.2
Bearing, Connecting Rod Data B.6
Bearing, Connecting Rod - To Renew F.1
Bearing, Crankshaft Main - Data B.6
Bearing, Crankshaft Main To Renew H.2
Belt, Fan To Adjust M.1
Belt, Fan - To Remove and Refit M.1
Block, Cylinder - Data B.3
Bush, Connecting Rod Small End - Data B.4
Bush. Connecting Road Small End - To Renew F.2
Camshaft - Data B.7
Camshaft - To Refit J.6
Camshaft - To Remove J.5
Capacity, Lubricating Oil - Data B.9
Capacity, Water (Coolant) - Data B.10
Case, Timing - To Refit Backplate J.4
Case, Timing - To Remove Backplate J.4
Case, Timing - To Remove and Refit Cover J.1
Checkover, Post Delivery C.3
Cooling System Data B.10
Cooling System - General C.4
Crankcase Pressure (Excessive)
Fault Diagnosis 0.1
Crankshaft Data B.6
Crankshaft - To Refit H.3
Crankshaft - To Remove
Crankshaft and Main Bearings
Data, Technical
De-Rating for Altitude
Difficult Starting
Dynamo, C40-1-
Description
Maintenance
Performance Data
Servicing
Description
H.3
H.i
B.1
B.1
0.1
0.4
0.5
0.5
0.5
Engine, Failure to Start - Fault Diagnosis
Engine Number Location
Engine Photographs
Erratic Running - Fault Diagnosis
Engine, Runs only Momentarily-
Fault Diagnosis
0.1
3
A.3 and A.4
D.1
0.1
Fault Diagnosis D.1
Filter, Fuel Oil - Data B.11
Filter, Fuel Oil - To Renew Filter Element N.3
Filter, Lubricating Oil - To Remove Element L.5
Filter, Lubricating Oil - To Remove Head Casting L.5
Filter, Lubriciating Oil - To Renew Filter Element L.6
Flywheel and Flywheel Housing -
To Remove and Refit
Foreword
Fuel Injection Equipment - Data
Fuel Oil Specification
P.1 and P.2
3
B.11
B.11
Gasket, Cylinder Head
E.7
Gear, Camshaft - Data B.9
Gear, Camshaft - To Remove J.2
Gear, Camshaft - To Refit J.2
Gear, Crankshaft - Data B.9
Gear, Fuel Pump - Data B.9
Gear, Fuel Pump - To Remove and Refit J.2 and J.3
Gear, Idler and Hub - Data B.9
Gear, Idler and Hub To Remove and Refit J.1
Gear, Lubricating Oil Pump Drive - Data B.10
Gear, Lubricating Oil Pump Drive To Remove L.3
Gear, Lubricating Oil Pump Drive - To Refit L.4
Glow Plugs - General C.2
Glow Plugs - Checking 0.9
Guide, Valve (Inlet and Exhaust) - Data B.7
Guide, Valve (Inlet and Exhaust)
To Remove and Refit E.4
Hand Grinding (Lapping-in Valves) E.5
Head, Cylinder - Data B.7
Head, Cylinder - To Refit E.7
Head, Cylinder - To Remove E.1
Heater (Starter) Switch C.1
Hub, Fuel Pump Drfve To Remove and Refit J.4
Index to Engine Photographs
Insert, Combustion Chamber - Data
Insert, Combustion Chamber -
To Remove and Refit
Insert; Valve Seat
Insert, Valve Seat To Fit
Knocking, Engine - Fault Diagnosis
A.2
B.7
E.4
E.6
E.6
0.1