Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HAKO Scrubmaster E10
Summary of Contents for HAKO Scrubmaster E10
- Page 1 Instruction manual Scrubmaster E10 (7739.03)
-
Page 2: Preface
We explicitly point out that no legal Intended use claims may be asserted based on the Dear Customer, The Scrubmaster E10 is a scrubber dry- information contained in this manual. We are certain that the excellent quali- er for the wet cleaning of hard floors. -
Page 3: Introduction
Notes on warranty be agreed on with Hako's authorized authorized contractual partner together dealers in accordance with § 6 and § 8 The terms defined in the purchase with the consignment note. -
Page 4: Table Of Contents
Contents Description Preface..........2 Controls..........11 Introduction Control Panel ........11 Proper Use......... 3 Detergent Infeed ......11 Notes on Warranty ......3 Squeegee Governor ....... 12 Acceptance of the Machine ....3 Mount/Dismount Brushes ....13 Squeegee ........14 Squeegee (Initial Fitting).... -
Page 5: Operation
General Safety Instructions General Safety Instructions Machines with known defects must not Turn the motors off, fold the be used. It will be of essence to make support roller and the operating handle down and protect the yourself familiar with all accessories Apart from the information contained and controls, as well as their func- machine against unintended move-... -
Page 6: Transport
General Safety Instructions Make sure to connect the Transport Hakomatic to a socket equipped with earthed pro- tective wire and to mains of Using the machine on public roads adequate voltage and fre- and places is not admitted. quency. Qualified personnel only are admitted to perform maintenance and repair Never collect explosive fluids, work. -
Page 7: Park Position
General Safety Instructions Handling Mains Cables Park Position Make sure that the mains cables are not damaged by passing over them, by pinching pulling or other impacts. If not operated, the Hakomatic has to Check the mains cables for aging and be stored in its park position. -
Page 8: Operation
Operation Hakomatic E 10 This cleaning agent acts on the floor Working Principle according to the specifications of the Wet cleaning of hard floorings requires manufacturer for about 5 to 10 min- equipment with squeegee and brushes utes, then scrub the floor again with suitable for the type of floor to be the squeegee being lowered. -
Page 9: First Operation
First Operation Assembly 1. Upon delivery, the Hakomatic has been secured by insulation blocks at The Hakomatic is delivered in a card- the bottom and the top to preclude board box. The bottom is a wooden unwanted movement of the machine. pallet to which the machine is fas- After taking the machine from the pal- tened by plastic straps. - Page 10 First Operation 3. Open the lateral brush head cover Make sure that all covers and flaps have been fitted by loosening the slotted screw using a before starting operation. coin. Then insert the enclosed brushes into the housing. The Hakomatic has been equipped with a slotted screw to facilitate removal and fastening of the A damaged mains cable has...
-
Page 11: Description
Description Control Panel Controls B. Suction motor switch ON/OFF Function is ON if switch "B" is in po- sition "1" Function is OFF if switch "B" is in position "0" 1. Brush motor, suction motor and wa- ter pump switches C. -
Page 12: Detergent Infeed
The front or the rear squeegee of the Loosen the slotted screw before dis- Hakomatic is lowered and has contact mounting the brush from the Hako- with the floor. The operator may matic. change squeegee position according Dismount the brush from the Hako- to the direction of travel of the matic after every use. -
Page 13: Mount/Dismount Brushes
Description If the Hakomatic is in its working po- During this movement, the rear Remove slotted screw of the brush sition and pushed forward, the rear cover. squeegee takes in the water. squeegee has contact with the floor Fasten supplied brushes at the drive while the front squeegee is lifted. -
Page 14: Squeegee (Initial Fitting)
Description Dismount Brushes Brush Maintenance Open brush cover in direction 2. Remove brushes Use the support roller located at the Clean brush compartment front side of the Hakomatic to set Insert brushes, close brush cover the machine into its park position. and secure with slotted screw. -
Page 15: Change Sealing Strips
Description Dismount Squeegee Mount Squeegee (Initial Fitting) Lift squeegee and hold it to the Lift brush head of the Hakomatic in squeegee holders (3). order to access the squeegee Mount squeegee (1) to the squee- screws. gee holder by means of fixing clip Remove both screws (2) as repre- (2) as represented- sented. -
Page 16: Clean Nozzle
The rear sealing strip can Make sure that the nozzle slot is as (I) Remove nozzle be turned round if worn at the mounting direction of the bru- Dismount brushes from the Hako- the front edge. shes. matic (see "Dismount/Mount Bru- Upright machine shes"). -
Page 17: Fill Water
Use detergents suitable for automatic machines (low foaming) in order to pre- clude damages at the suc- tion turbine. We recom- mend Hako detergents for Fill Water cleaning and care, which are perfectly adapted to the Fill fresh water and detergent as Hakomatic. -
Page 18: Operation
Operation Operation Make sure that during oper- At the end of cleaning: ation of the machine the Use the button to take the support mains cable always lies Turn machine off and set it to its into working position. behind the operator. park position Turn switch "A"... -
Page 19: Soiled And Fresh Water Tanks
Operation Soiled and Fresh Water Tanks A suction hose delivers the soiled Clean Soiled and Fresh Water Tanks water into the soiled water tank. Fresh water tank Do not take in larger amounts of secondary Filter water (water pools) Floater To avoid settling of residues Slowly tilt the tank as represented to empty and rinse the soiled... -
Page 20: Electric System
Operation Electric System The electric system of the Hakomatic Reset the cut-out by pushing down the E 10 operates at a mains voltage of transparent dome of the fuse box. 230V/50Hz. After tripping, wait for approx. 30 sec- After opening the machines top, the onds before resetting. -
Page 21: Technical Data
Technical Data Dimensions Length Width Height Working width Squeegee Scrubbing Area performance m²/h Theoretical 1400 up to km/h Driving speed... - Page 22 Technical Data Weights (with closed handle) Empty weight, dry Total weight, operable, wet Wheels Rear wheel, diameter Tank capacities Fresh water tank Litre Soiled water tank Litre Throughput, max. Litre/min 0,22 Brush head No. of brushes Qty. Brush diameter Brush speed Brush pressure, max.
- Page 23 Technical Data Elektric system Service voltage AC/Volt 230 ± 10% Mains frequency Protection class, compl. machine EN 60335-2-72 Protection type, compl. machine EN 60335-2-72 IP X3 Nominal rating, total, max. 1340 Fuse for brush motor Fuse for suction motor T 6.3 Fuse for pump...
- Page 24 Technical Data Parts number Brushes Polyamide brushes 7740 Polypropylene brushes 7741 Silicon carbide brushes 7742...
-
Page 25: Maintenance
Maintenance Maintenance Information Turn the machine off and disconnect the mains plug Compliance with our recommenda- before cleaning or maintain- tions concerning maintenance work ing the machine. will give you the certitude of always For safety reasons, secure the lifted having a machine at your disposal tank lid against inadvertently closing or which is ready to work and in good... - Page 26 Maintenance...
- Page 27 Maintenance Disconnect the mains plug before executing mainte- nance or repair work. After these works have finished, proceed to a safety check according to VDE standard 0701.
-
Page 28: Ec-Declaration Of Conformity
EC Declaration of Conformity (corresponds to EC Directive 2006/42/EC) Name of the person authorised for Hako GmbH Reference was made to the following Hako to compile the technical file: standards and/or norms and/or techni- Hamburger Straße 209-239 cal specifications to ensure proper im-... - Page 29 Notes...
- Page 30 Spitzentechnik für eine saubere und schönere Umwelt Advanced Technology for a Cleaner, Better Environment · · Hako GmbH Hamburger Str. 209-239 D-23843 Bad Oldesloe · +49 4531 806-0 Fax +49 4531 806-338...