HAKO Scrubmaster B45 Instruction Manual

HAKO Scrubmaster B45 Instruction Manual

Hide thumbs Also See for Scrubmaster B45:
Table of Contents

Advertisement

Instruction Manual
Scrubmaster B45 (7700)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Scrubmaster B45 and is the answer not in the manual?

Questions and answers

Afsar
April 8, 2025

Hi, I have scrubmaster B45 CL, it’s showing errors, can you help me to have to remove the errors pls.

2 comments:
Mr. Anderson
April 9, 2025

To remove errors from the HAKO Scrubmaster B45 CL:

1. Check the four-digit service code shown with flashing dots.
2. Identify the cause using the error code table:
- 1.2.5.2: Let the brush motor cool down.
- 1.2.6.1: Remove foreign bodies blocking the brush.
- 1.2.6.5 or 1.4.2.1: Allow the machine to cool down or contact Hako service.
- 1.2.6.6: Install the brush.
- 3.2.1.1 or 4.6.1.2: Inform Hako service.

If the issue persists, note the code and contact an authorized Hako dealer.

This answer is automatically generated

Timothy
April 16, 2025

@Mr. Anderson hi I have hako H0510 scrubmaster B45 2016 model showing that they is no battery on but I replaced battery put new naw is showing error 2.002,3.2.1.1,0776

Summary of Contents for HAKO Scrubmaster B45

  • Page 1 Instruction Manual Scrubmaster B45 (7700)
  • Page 2: Introduction

    • 7700.10 to safety. Please observe the safety The Scrubmaster B45 may only be op- • 7700.12 provisions (see chapter "Safety Infor- erated, serviced and repaired by per- • 7700.26 mation”).
  • Page 3: Information On The Warranty

    Maintenance not represent a source of risks to chil- work must be completed by an author- dren. ized Hako service center and confirmed Dispose of the machine in accordance in the “maintenance logbook”; this with the applicable local regulations.
  • Page 4: Table Of Contents

    Maintenance and Service . 36 5.7.3 Changing the sealing strip . . 50 Before Putting into Operation 13 Hako system maintenance. . 36 Switching the machine on . . 14 Maintenance Document ..37 Operation ....15 Maintenance Schedule.
  • Page 5 Table of Content Squeegee ....51 5.8.1 Cleaning the squeegee ..51 5.8.2 Changing the sealing strips . 51 5.8.3 Adjusting the sealing strips. . 52 Circular brush head .
  • Page 6: Safety Information

    cribed aSafety information Safety informa- cribed a tion Safety and Warning Symbols All paragraphs in this manual referring to your personal safety, the safety of your machine and the environment pro- tection are attributed one of the follow- ing warning symbols: Symbol Hazardous for...
  • Page 7: General Provisions

    • Persons being trained by qualified Hako technicians only are autho- rised to operate, service and repair the machine. • You are advised to thoroughly study the safety instructions since precise...
  • Page 8: Operating Information

    • Start driving immediately after er. Hako assumes no liability for switching on the brush head drive damage to the battery caused by a otherwise imprints of the brush could fault when the battery is charged for be produced on the floor.
  • Page 9: Maintenance Information

    • Always disconnect the battery termi- mediately and clear the fault. your nearest Hako service center. nal before starting any work on the • Work on the electrical equipment • The maintenance work and mainte- electrical installation.
  • Page 10: Information For Protection Of Environment

    DIN VDE 0620-1. gravity, only batteries approved by gents, see Water Management Act.  • Pay attention that no water or fluids Hako may be installed at the intend- •  can get on to live machine parts. If ed position.
  • Page 11: Labels On The Machine

    cribed aSafety information Labels on the machine The following safety and warning labels are attached to the machine where eas- ily legible. Missing or illegible labels must be replaced immediately. Company logo (Fig. 1/1) Rating plate (Fig. 1/2) Explosive gases (Fig. 1/3) Yellow point (maintenance parts) (Fig.
  • Page 12 cribed aSafety information Waste water draining hose (Fig. 2/1) A = Read and observe the operating manual (Fig. 2/2) B = Maximum permissible gradient 2% (Fig. 2/2) C = Do not clean the machine with a pressure washer (Fig. 2/2) Only maintenance-free batteries...
  • Page 13: First Operation

    First Operation First Operation Before Putting into Operation Complete the following inspections be- Instruction fore taking the machine into operation: Instruction is required before first oper- 1. Check the area around the machine ation. First instruction into handling of for signs of leakage. Hoses, lines the machine must be held by a qualified and tanks must be free from any person sent by your local PowerBoss...
  • Page 14: Switching The Machine On

    First Operation Switching the machine on • Switch the machine on by actuating the switch (Fig. 4/1) from position (0) Before switching the machine to position (1). on, please read the safety in- formation in Chapter 1. Carry out the following preliminary work so that the machine is ready to operate: •...
  • Page 15: Operation

    First Operation Operation Scrubmaster B45 CL 1. Switch the machine on using the key Scrubmaster B45 switch. All the units are in Standby 1. Switch the machine on at the main 2. Lower the squeegee using the switch. The suction turbine is squeegee lever.
  • Page 16: Useful Tips

    Hako cleaning agent and the The floor should be treated twice in the optimum dosage to suit your needs.
  • Page 17: Error Code Table

    In addition to the Service indicator (wrench), a four-digit service code ap- pears in the indicator field. The dots in the service code flash. Clear the fault or note down the service code and inform your authorized Hako dealer. Error Cause Remedy 1.2.5.2.
  • Page 18: Stopping And Switching Off The Machine

    4. Switch off the machine with the main 5. Check the sealing strips and suction switch. hose. 6. Check the electrical equipment, Scrubmaster B45 CL functions and settings. 1. Release the safety switch: 7. Clean the machine. - The traction drive, brush drive and 8.
  • Page 19: Transportation And Lashing Points

    Lash the machine down securely. To do this, it must be secured at the front (on both sides) and rear at the hold points (Fig. 5/1). Fig.5 Scrubmaster B45...
  • Page 20: Operation

    Operation Operation Method of operation General information The Scrubmaster B45 is a scrubber dry- er for the wet cleaning of hard floors. 3.1.1 Brush head The brush in the brush head (Fig. 6/1) is driven by an electric motor. The brush head is lowered by means of the brush pedal.
  • Page 21: Squeegee

    3.1.5 Power flow / traction drive The hand-guided Scrubmaster B45 is optimally supported by the power flow of the brush drive. The Scrubmaster B45 CL is provided with a continuously adjustable traction drive.
  • Page 22: Batteries And Charger

    Operation 3.1.6 Batteries and charger The machine is equipped with mainte- nance-free batteries (Fig. 8/1), a fully automatic battery charger (Fig. 8/2) and a total discharge signal transducer (TSG) to protect it against total dis- charge. Pay attention here to the safety information.
  • Page 23: Options

    • Mop holder and tool net (7725) • Covering disk brush stainless steel (7798.20) Scrubmaster B45 only: • Onboard dosing system (7678) Scrubmaster B45 CL only: • Onboard dosing system (7678.05) Scrubmaster B45 CL/CLH only: • Tool connection (7724) • Suction hose (7766) •...
  • Page 24: Operating And Indicator Ele- Ments

    Operation Operating and indicator ele- ments 3.2.1 Operating panel Scrubmaster B45 1 Indicator field for: - operating hour counter, - service indicator, and - charge status indicator 2 Charge mode indicator 3 Main switch 4 Bail system switch 5 Brush ejector Fig.9...
  • Page 25 2 icons: charge level 40%-20% Clear the fault or note down the service cates all operating states. 1 icon: charge level less than 20% code and inform your authorized Hako Operating hour counter dealer. Battery icon flashes = three minutes un- After switching on, the software version, OFF.
  • Page 26 Flashing of the bottommost LED is indicative of a fault. See charger manual. Main switch (Fig. 9/3) Hako chargers are designed to The main switch is used to switch the work continuously, i.e., at the electrical system on and off.
  • Page 27 Operation Scrubmaster B45 CL 1 Indicator field for: - operating hour counter, - service indicator, and - charge status indicator 2 Charge mode indicator 3 Key switch 4 Bail system switch 5 Direction switch 6 Driving speed control 7 Symbol for silence kit...
  • Page 28 1 icon: charge level less than 20% Clear the fault or note down the service Operating hour counter code and inform your authorized Hako Battery icon flashes = three minutes un- dealer. After switching on, the software version, OFF.
  • Page 29 Flashing of the bottommost LED is indicative of a fault. See charger manual. Key switch (Fig. 10/3) Hako chargers are designed to The key switch is used to switch the work continuously, i.e., at the electrical system on and off. The indica- Charge mode indicator (Fig.
  • Page 30 Operation Direction switch (Fig. 10/5) Symbol for silence kit (Fig. 10/7) Silence kit button (Fig. 10/9) The direction switch is used to preselect The LED lights up when the silence kit The silence kit button is used to switch the driving direction for the machine. function is switched on.
  • Page 31 Operation Attach brush: Switch the machine on again using the main switch. Position the brush cen- Solution dosage button (Fig. 10/11) Brush ejection button (Fig. 10/13) tered under the raised brush head. The solution quantity can be adjusted The brush can be removed for mainte- Lower the brush head.
  • Page 32: Operating Elements On The Machine

    1 Solution tank filling neck 2 Squeegee lift lever 3 Solution filter 4 Solution draining hose 5 Power supply line to charger 6 Brush head lift foot pedal 7 Waste water draining hose 8 Hand valve for water dosage  (Scrubmaster B45 only) Fig.11...
  • Page 33 Solution hand valve (Fig. 11/8) The solution tank draining hose is used to drain the solution. Scrubmaster B45 features a hand valve for adjusting the amount of water sup- plied to the brush head. The solution quantity can be regulated between 0 l/...
  • Page 34: Technical Data

    Technical Data Technical Data B45 TB* B45 CL TB** B45 CLH TB** B45 CL WB** Machine length 127/135 127/135/137 Machine height at operating bar Machine width w/o squeegee 50/56 50/56/67 56/86 60/86 Machine width w/ squeegee 76/86 76/86/95 56/86 60/86 Working width 43/51 43/51/65...
  • Page 35 Technical Data Noise emission value B 45t B 45 CL/CLH Sound power level (L wAd ) measured according to DIN EN 60335-2-72 dB (A) under maximum working conditions: The sound pressure level (L pA ) (at the ear of the operator) measured according dB (A) to DIN IEC 60335-2-72 under normal working conditions: Measurement inaccuracy (K pA ):...
  • Page 36: Maintenance And Service

    Hako system maintenance I: vice The Hako system maintenance: (every 125 operating hours) • ensures that the Hako vehicle is al- Completed by technical experts from an General information ways ready for operation (preventive authorized Hako service center in ac-...
  • Page 37: Maintenance Document

    Maintenance and Service Maintenance Document Handing over Hako-System-Maintenance I Hako-System-Maintenance II Hako-System-Maintenance I 125 operating hours 250 operating hours 375 operating hours Upgrade Workshop stamp Workshop stamp Workshop stamp Test drive Handing over to the customer Instruction carried out on:...
  • Page 38: Maintenance Schedule

    Maintenance and Service Maintenance Schedule The daily and weekly maintenance in- Hako-System Maintenance Cus- tervals are to be performed by the cus- tomer tomer/operator. Interval To be performed daily weekly Fill clear water tank and proceed to chemical agent dosage...
  • Page 39 Maintenance and Service Hako-System Maintenance I The following maintenance woks are to be performed by an authorised Hako Service workshop. Interval To be performed every 125 hours of operation Check battery charger Check tank lid sealing of the soiled water tank and replace if required...
  • Page 40 Service workshop. Interval To be performed every 250 hours of operation Perform maintenance works according to Hako-System Maintenance I Inspect steering rollers for tread damages and bearing slackness and replace if required Check function of water pump and replace if required...
  • Page 41 1000 operating hours) Check brake of the travel drive motor (Scrubmaster B45 CL only) Clean travel drive motor (Scrubmaster B45 CL only) from carbon dust and check carbon brushes for smooth operation and wearing and replace carbon brushes if required...
  • Page 42: Battery System

    Maintenance and Service Battery system  1 Indicator field w/ charge status indi- cator 2 Charge mode indicator 3 On-board charger 4 Charger power plug 5 Power plug receptacle and vehicle immobilizer 6 Battery terminals 7 Batteries 8 Waste water tank 9 Circuit diagram 10 Connecting line Fig.12...
  • Page 43: Charging Batteries

    (TSG) in the chine will not be ready to oper- first time. Hako assumes no li- machine control unit. Four segments on ate until the power plug has ability for damage to the bat-...
  • Page 44: Total Discharge Signal Trans- Ducer (Tsg)

    The total discharge signal transducer may only be adjust- We recommend our licensed ed by a licensed Hako work- Hako Customer Service. shop! 5.4.4 Servicing the driving batteries Never keep discharged batteries but re- charge them immediately!
  • Page 45: Solution Tank

    Maintenance and Service Solution tank 1 Solution tank 2 Marking 3 Fill level hose 4 Solution filter 5 Tank cap Fig.13 Scrubmaster B45...
  • Page 46: Filling The Solution Tank

    Maintenance and Service 5.5.1 Filling the solution tank 5.5.3 Cleaning the fresh water filter Fill the solution tank (Fig. 13/1) before Check the solution filter (Fig. 13/4) starting work or as necessary. Park the weekly and clean or replace it as neces- vehicle on a level floor area.
  • Page 47: Soiled Water Tank

    Maintenance and Service Soiled Water tank 1 Soiled Water Tank 2 Drain hose 3 Suction filter 4 Tank lid 5 Drain valve sealing 6 Tank lid sealing Fig.14...
  • Page 48: Empty Soiled Water Tank

    Maintenance and Service 5.6.1 Empty Soiled Water Tank Turn off the cap. Clean soiled water tank (Fig. 14/1) at daily intervals, as required or upon acoustic signal (increased suction tur- bine speed). 1. Take machine to appropriate place for discharge. 2.
  • Page 49: Clean Suction Filter

    Maintenance and Service 5.6.2 Clean Soiled Water Tank 5.6.4 Checking the seal of the drain 5.6.5 Checking the Tank lid seal hose Clean soiled water tank (Fig. 14/1) at Check the functionality of the seal in the daily intervals or as required. Check the functionality of the seal from tank cap (Fig.
  • Page 50: Brush Head

    Maintenance and Service Brush head 1 Brush 2 Brush head 3 Brush head lift lever 4 Brush ejection button 5 Deflector roller 6 Sealing strip Fig.15...
  • Page 51: Changing The Brushes

    Maintenance and Service 5.7.1 Changing the brushes Attach brush: 5.7.2 Changing the deflector roller Check the brushes (Fig. 15/1) in the Check the deflector roller (Fig. 15/5) Switch the machine on again using the brush head (Fig. 15/2) weekly for signs weekly and change it as necessary.
  • Page 52: Squeegee

    Maintenance and Service Squeegee 5.8.1 Cleaning the squeegee 5.8.2 Changing the sealing strips Check the squeegee (Fig. 16/1) daily Check the inner and outer sealing strips 1 Squeegee and clean it as necessary. on the squeegee (Fig. 16/1) weekly for 2 Star-shaped knob To clean the squeegee raise it, discon- signs of wear.
  • Page 53: Adjusting The Sealing Strips

    Maintenance and Service 5.8.3 Adjusting the sealing strips Angle adjustment The angle adjustment is decisive in controlling whether the squeegee's sealing strips lie evenly on the floor. 1. Park the machine on a level surface and lower the squeegee. 2. Loosen the counternut on the adjust- ing bolt (Fig.
  • Page 54 Maintenance and Service Height adjustment The height adjustment is set to 3 mm at the factory. If streaks appear despite an optimum angle adjustment, the dis- tance of the rollers to the floor must be adjusted by changing the number of washers on the holder.
  • Page 55: Circular Brush Head

    Maintenance and Service Circular brush head Cleaning the brushes Changing the brushes Clean the brushes in the brush head Check the brushes (Fig. 15/4) in the 1 Brush head lift lever (Fig. 15/2) daily or as necessary. brush head weekly for signs of wear. In 2 Brush head the case of wear to a brush length of 1.
  • Page 56: Rotary Brush Head

    Maintenance and Service 5.10 Rotary brush head 1 Slotted-head screw 2 Cover 3 Waste container 4 Deflector roller 5 Catch 6 Brushes 7 Sealing strips 8 Spray jets 9 Knurled screws Fig.20...
  • Page 57: Cleaning The Brush Head

    Maintenance and Service 5.10.1 Cleaning the brush head 5.10.2 Changing the brushes 5.10.3 Cleaning the waste container Check the brush head daily and clean it Check the brush head weekly and Check the waste container daily and as necessary. change it as necessary. clean it as necessary.
  • Page 58: Changing The Sealing Strips

    Maintenance and Service 5.10.4 Changing the sealing strips 5.10.5 Checking the spray jets 5.10.6 Change deflector roller Check the sealing strips (Fig. 20/7) Check the spray jets daily and clean Check deflector rollers (Fig. 20/4) at weekly and change them as necessary. them as necessary.
  • Page 59 Maintenance and Service...
  • Page 60 Maintenance and Service...
  • Page 61: Ec-Declaration Of Conformity

    For the relevant implementation of the Name of the person authorised for Hamburger Straße 209-239 safety and health requirements men- Hako to compile the technical file: D-23843 Bad Oldesloe tioned in the Directives, the following standard (s) and / or technical specifica- Ludger Lüttel...
  • Page 62 Advanced Technologie for a Cleaner, Better Environment · · Hako GmbH Hamburger Str. 209-239 D-23843 Bad Oldesloe ·  +49 4531 806-0 Fax +49 4531 806-338...

This manual is also suitable for:

7700

Table of Contents

Save PDF