Sony MSW-970 Operation Manual page 49

If you turn the MENU knob clockwise or
counterclockwise, the number changes in the
following sequence: M y 1SEC y 2SEC y
3SEC y 4SEC y 5SEC y 6SEC y 7SEC y
8SEC y 9SEC y 10SEC y 15SEC y 20SEC
y 30SEC y 40SEC y 50SEC y 1MIN y
2MIN y 3MIN y 4MIN y 5MIN y 6MIN y
7MIN y 8MIN y 9MIN y 10MIN y 15MIN
y 20MIN y 30MIN y 40MIN y 50MIN y
1H y 2H y 3H y 4H y 6H y 12H y 24H.
When a trigger interval time other than M is displayed,
the camcorder is in Continuous Trigger mode of
Manual Interval Rec. The TALLY indicator (green)
flashes (1 flash/second).
3
Push the MENU knob.
The ? mark on the left of setting returns to a z mark,
and the z mark on the left of "TRIGGER
INTERVAL" returns to an
4
Turn the MENU knob to move the
LIGHTING.
U03 FUNCTION1
ASSIGN SW <1>
ASSIGN SW <2>
TURBO SW
DF/NDF
END SEARCH
CACHE/INTVAL REC:
NUMBER OF FRAME :
TRIGGER INTERVAL:
PRE-LIGHTING
5
Push the MENU knob.
b
The mark on the left of "PRE-LIGHTING" changes
to a z mark, and the z mark on the left of the setting
changes to a ? mark.
6
Turn the MENU knob clockwise or counterclockwise
until the desired time interval at which to turn on the
light before recording starts appears.
If you turn the MENU knob clockwise or
counterclockwise, the PRE-LIGHTING time changes
in the following sequence: OFF y 2SEC y 5SEC
y 10SEC.
Notes
• To turn on the light automatically before recording
starts by setting the PRE-LIGHTING item to ON, be
sure to set the LIGHT switch to AUTO. Also, set the
switch of the light connected to the LIGHT
connector to ON.
The light automatically turns on and off in
Continuous Trigger mode of Manual Interval Rec.
However, if the duration the light should be off is
less than 5 seconds, the light is on continuously.
b
mark.
b
mark to PRE-
: ATW
: OFF
: TURBO
: DF
: OFF
M.INT
1
1SEC
: OFF
• When the LIGHT switch is set to MANUAL and the
switch of the light is set to ON, the light is always on.
7
Push the MENU knob.
The ? mark on the left of setting returns to a z mark
and the z mark on the left of PRE-LIGHTING returns
b
to an mark.
8
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
The menu disappears from the viewfinder screen and
the message INTERVAL *SEC *FRAME, indicating
Continuous Trigger mode of Manual Interval Rec,
appears along the bottom of the viewfinder.
*SEC indicates the trigger interval preset and
*FRAME indicates the number of frames preset.
The display indicating the current status of the
camcorder appears along the top and bottom of the
viewfinder.
Note
The settings for Continuous Trigger mode of Manual
Interval Rec are maintained until changed. However, if you
switch the camcorder power off, all Manual Interval Rec
mode settings are cleared except for the NUMBER OF
FRAME, TRIGGER INTERVAL, and PRE-LIGHTING
settings. To use Continuous Trigger mode of Manual
Interval Rec again after switching on the power, perform
steps 1 and 2 in "Setting Single Trigger mode of Manual
Interval Rec" on page 47.
Recording in Continuous Trigger mode of
Manual Interval Rec
Follow the procedure below to shoot pictures in
Continuous Trigger mode of Manual Interval Rec.
Note
When you use cassettes on which nothing is recorded, such
as brand new cassettes, be sure to record color bars for
more than 2 seconds at the beginning of a cassette.
1
After performing the basic procedures for shooting
and recording following the instructions in "3-2-1
Basic Procedures" on page 36, secure the camcorder
so that it will not move.
2
Push the VTR START button on the camcorder or the
VTR button on the lens.
The camcorder starts recording in Continuous Trigger
mode of Manual Interval Rec, and the flashing cycle of
the TALLY indicator (green) changes from 1 flash/
second to 4 flashes/second, and the message
49
Recording