Sony BRC-Z330 Operating Instructions Manual page 26

• An unsupported optional interface card is
inserted in the card slot of the BRU-SF10.
Remove the card after turning off the power,
and then restart the unit.
Off: The unit is in normal operation.
E SD indicator
This indicator lights when a BRBK-SA1 optional
interface card is installed, or when a BRBK-HSD2
is installed and its rear switch is set to SD.
F Camera ID indicators
The number for the current camera address lights
orange.
For details on setting the camera address, see
"Q VISCA FUNCTION switches" on page 26.
G Status indicators
The current communication format, baud rate, and
video format settings light green.
For details on configuring these settings, see
"Q VISCA FUNCTION switches" on page 26.
H DATA MIX switch
When the SD indicator is lit, set this switch to ON
to overlap the menu display with the SD image
signals from any installed BRBK-SA1 and
BRBK-HSD2 interface cards on which the rear
switch is set to SD.
Set this switch to OFF to hide the menu display.
Rear
9 0 qa
IN OUT
EXT SYNC
CAMERA
I CAMERA connector
Connect to the optical connector of the BRBK-SF1
HD Optical Multiplex Card installed in the
BRC-Z330 camera using the CCFC-S200 Optical
Fiber Cable.
A dustproof cap is attached at the factory.
Do not remove this cap if you do not intend to
connect an optical fiber cable. Dustproof caps are
also attached to the BRBK-SF1 and CCFC-S200.
Do not remove these caps when the connectors are
not in use.
J EXT SYNC IN connector
Accepts external video sync signals.
26
Location and Function of Parts
qs qd qf qg qh
IN OUT
1 2 3 4 5 6 7 8 9
RGB/COMPONENT VISCA RS232C
VISCA RS422
AUDIO OUT
L
FUNCTION
1
R
10
DC 12V
ql qk qj
K EXT SYNC OUT connector
Supplies external video sync signals input from the
EXT SYNC IN connector.
When a cable is connected to this connector, the
75-ohm termination for inputs is automatically
opened, and signals input to the EXT SYNC IN
connector are output from this connector.
L
RGB/COMPONENT connector
Supplies the images from the camera as YPbPr or
RGB signal.
M VISCA RS-232C IN connector
Connect to the RM-BR300 Remote Control Unit
(not supplied). When you connect multiple
cameras, connect it to the VISCA RS-232C OUT
connector of the previous camera in the daisy chain
connection.
N VISCA RS-232C OUT connector
When you connect multiple cameras, connect it to
the VISCA RS-232C IN connector of the next
camera in the daisy chain connection.
CAUTION
When you connect the RS-232C connecting cable
of the unit to peripheral device, use the supplied
cable to prevent malfunction due to radiation noise.
O VISCA RS-422 connector
Connect to the VISCA RS-422 connector of the
camera or another BRC-Z330 HD Optical
Multiplex Unit.
For the connection to the VISCA RS-422
connector, see "Using the VISCA RS-422
Connector Plug" on page 89.
P AUDIO OUT L/R jacks
Loop through output of the audio line signal input
from the AUDIO IN jacks on the BRBK-SF1 HD
Optical Multiplex Card inserted into the camera via
the Optical Fiber Cable.
Q VISCA FUNCTION switches
These switches are used for the VISCA
communication settings.
Switch 1 (RS-232C/RS-422 selector)
Set to ON for RS-422, or OFF for RS-232C.
Switch 2 (Communication baud rate
selector)
Set to ON for 38400 bps, or OFF for 9600 bps.
Switches 3 to 5 (Camera address selectors)
Set the address of the camera.