Waldorf RN8110GE Installation And Operation Manual
800 series gas target top range
electric ovens
Hide thumbs
Also See for RN8110GE:
- Installation and operation manual (29 pages) ,
- Installation and operation manual (27 pages) ,
- Installation and operation manual (32 pages)
Related Manuals for Waldorf RN8110GE
Summary of Contents for Waldorf RN8110GE
-
Page 1: Electric Ovens
I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l Gas Target Top Range Electric Ovens RNL8110GE RN8110GE RN8110GEC RNL8110GEC Date Purchased... - Page 2 MANUFACTURED BY Moffat Limited Christchurch New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited E.Mail: vsales@moffat.com.au Main Office: (tel): +61 (03) 9518 3888 (fax): +61 (03 9518 3833 Service: (tel): 1800 622 216 Spares: (tel): 1800 337 963 Customer Service: (tel): 1800 335 315 (fax): 1800 350 281 CANADA Serve Canada...
-
Page 3: Table Of Contents
Contents Waldorf Gas Target Top Range Electric Oven RN(L)8110GE Gas Target Top Range Electric Static Oven. RN(L)8110GEC Gas Target Top Range Electric Convection Oven. Introduction ....................2 Specification ....................3 Model Numbers Covered in this Specification General Gas Supply Requirements... -
Page 4: Introduction
Introduction We are confident that you will be delighted with your WALDORF Gas Target Top Range Electric Ovens and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Waldorf appliance, there are two important things you can do. -
Page 5: Specification
Specifications Model Numbers Covered in this Specification RN[1]8110GE Gas Target Top Range Electric Static Oven - 900mm. RN[1]8110GEC Gas Target Top Range Electric Convection Oven - 900mm. NOTE: [1]: - Back Options; - Standard Models. - Low Back Models. General A commercial heavy duty, gas fired Target Top having a high output, two stage double-ring cast iron burner offering accurate temperature control and infinitely variable heat with heat radiating out from centre of Target Top. -
Page 6: Electrical Supply Requirements
Electrical Supply Requirements 1-Phase Connection 3-Phase Connection MODEL 1P+N+E, 230-240V 3P+N+E, 400-415V L1 - 8.2 Amps 6.5 kW, RN8110GE 6.5 kW L2 - 9.2 Amps 26.6 Amps @ 235 V L3 - 9.2 Amps L1 - 9.5 Amps 6.8 kW, RN8110GEC 6.8 kW... -
Page 7: Dimensions
Dimensions Dimensions RN(L)8110GE / GEC... -
Page 8: Installation
Waldorf Target Top Range Electric Ovens are designed to provide years of satisfactory service, and correct installation is essential to achieve the best performance, efficiency and trouble-free operation. -
Page 9: Clearances
Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. Combustible Surface Non Combustible Surface Left / Right hand side 50mm Rear 50mm * Side clearances can be 50mm when adjacent surface is at least 100mm below cooking surface. Assembly This model is delivered completely assembled. -
Page 10: Gas Connection
Installation Gas Connection NOTE: ALL GAS FITTING MUST ONLY BE CARRIED OUT BY AN AUTHORISED PERSON. It is essential that gas supply is correct for appliance to be installed and that adequate supply pressure and volume are available. The following checks should be made before installation:- a. -
Page 11: Electrical Connection
Installation Manifold Test NOTE: Measure burner operating pressure at manifold test Point point with target top burner (Inner and outer ring) operating at full setting. Turn ‘Off’ mains gas supply and bleed gas out of appliance gas lines. Turn ‘On’ gas supply and appliance. Verify operating pressure remains correct. -
Page 12: Commissioning
Installation NOTE: This appliance must be earthed. Fixed wiring installations must incorporate an all-pole disconnection switch. Correctly locate appliance into its final operating position and using a spirit level, adjust legs so that appliance is level and at correct height. Connect power supply to appliance. -
Page 13: Operation
/ operator. Waldorf appliances have been designed to provide simplicity of operation and 100% safety protection. Improper operation is almost impossible, however bad operation practices can reduce the life of the appliance and produce a poor quality product. -
Page 14: Lighting Pilot Burner (Target Top)
Operation Lighting Pilot Burner (Target Top) Remove centre casting with casting removal tool. Depress control knob and rotate anti-clockwise to ‘PILOT’ position. With control knob depressed, manually light pilot burner located in front of main burner. Hold in control knob for approximately 10 to 15 seconds, then release. Pilot burner should remain alight. -
Page 15: Oven
Operation Oven ! IMPORTANT DO NOT USE aluminium foil or trays directly on cast iron sole plate(s). NEVER block or cover openings on each side of sole plate(s). The oven is fitted with top and bottom elements. The thermostat maintains overall oven temperature. -
Page 16: Cleaning And Maintenance
Cleaning and Maintenance General Caution Always turn ‘Off’ electrical and gas supply before cleaning. This appliance is not water proof. Do not use water jet spray to clean interior or exterior of appliance. Clean Target Top / Range regularly. A clean appliance looks better, will last longer and will perform better. -
Page 17: Periodic Maintenance
Cleaning and Maintenance Target Top a. This should be kept clean of any build up of spillage’s of food. Provided the cast iron work surface is regularly used it will maintain itself in good condition with no special cleaning requirements required. b. -
Page 18: Fault Finding
Fault Finding This section provides an easy reference guide to the more common problems that may occur during operation of your appliance. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this section covers the most common problems reported, you may encounter a problem not covered in this section. -
Page 19: Wiring Schematic
Wiring Schematic RN(L)8110GE... -
Page 20: Rn8110Ge
Wiring Schematic RN(L)8110GEC... -
Page 21: Rn8110Ge
Wiring Schematic Wiring Layout for Static Oven Wiring Layout for Convection Oven... -
Page 22: Gas Conversion And Specifications
Gas Conversion and Specifications Conversion Procedure Caution Ensure Appliance is isolated from gas and electrical supplies before commencing servicing. NOTE: These conversions should only be carried out by qualified persons. All connections must be checked for leaks before re-commissioning appliance. ... -
Page 23: Gas Specifications
Gas Conversion and Specifications NOTE: Ensure pilot burner and thermocouple are Pilot Burner Main Burner correctly located and pilot burner aligns Ignition Port Thermocouple with main burner ignition port. (Refer to 2± 2.0 18± 2.0 figure opposite for correct fitting and alignment dimensions). -
Page 24: Gas Specifications
Gas Conversion and Specifications Gas Type Identification Label On completion of the gas conversion, replace gas type identification label, located:- - At the rear of the unit, above the gas connection. - Beside the Rating Plate. Commissioning Before leaving the converted installation; Check all gas connections for leakages using soapy water or other gas detecting equipment. -
Page 25: Replacement Parts List
Replacement Parts List Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for servicing and repair of this appliance. Instructions supplied with parts should be followed when replacing components. further information servicing instructions, contact your nearest authorized service branch (contact details are as shown on reverse of front cover of this manual). - Page 26 - Australia / New Zealand Only Gas Type to Convert to Model Nat. Gas Butane Town Gas RN8110GE / GEC 231972 231971 231973 N/A (*) NOTE: (*) Town Gas Option is only available with specific ex-factory built Town Gas models, which can also be converted to any other gas.
Need help?
Do you have a question about the RN8110GE and is the answer not in the manual?
Questions and answers