Sony Digital8 DCR-TRV410 Service Manual page 137

3-1-2. Precautions on Adjusting
1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VTR or
PLAYER" or set the "Forced VTR Power ON mode" using the
adjustment remote commander (Note 1).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note 2).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note 3)
2) The front panel block (MA-356 board, focus ring, microphone
unit) need not be connected except during "Battery end
adjustment" and "IR transmitter adjustment". To remove,
disconnect the following connectors.
VC-213 board CN903 (22P 0.5mm)
3) By setting the "Forced VTR Power ON mode" or "Forced
Camera Power ON mode", the video section can be operate
even if even if the cabinet (R) block ( Camera function switch
(CF-64 board), LCD block, viewfinder. power switch) has been
removed. But removing the cabinet (R) block (removing the
VC-213 board CN911) means removing the lithium 3V power
supply (CF-64 board BH001) , data such as date, time, user-set
menus will be lost. After completing adjustments, reset these
data. If the cabinet (R) block has been removed, the self-
diagnosis data, data on history of use (total drum rotation time
etc. ) will be lost. Before removing, note down the self-diagnosis
data and data on history use (data of page: 2, address: A2 to
AA). (Refer to "SELF-DIAGNOSIS FUNCTION" for the self-
diagnosis data, and to "5-4. Service Mode" for the data on the
history use.) To remove the cabinet (R), disconnect the
following connectors.
1. VC-213 board CN911 (50P, 0.5mm)
2. DD-117 board CN933 (10P, 1.0mm)
4) The lens block (CD-212/213 board) and the intelligent
accessory shoe need not be connected except during "Battery
end adjustment". To remove, disconnect the following
connectors.
1. VC-213 board CN501 (16P, 0.5mm)
2. VC-213 board CN551 (24P, 0.5mm)
3. Intelligent accessory shoe (8P, 0.5mm)
Note 1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned
on with the front panel block removed.
After completing adjustments, be sure to exit the "Forced VTR
Power ON mode".
Note 2: Setting the "Forced Camera Power ON" mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the front panel block removed.
After completing adjustments, be sure to exit the "Forced
Camera Power ON mode".
Note 3: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
Note 4: 720H model:DCR-TRV410/TRV510
960H model:DCR-TRV410E/TRV510E
720H model
960H model
5-42
CD board
CD-212
CD-213