Kubota D1503-M-DI Workshop Manual page 32

03-M-DI Series, WSM
ENGINE BODY (Continued)
Balancer Shaft Journal 2 to Balancer Shaft
Bearing 2 (Balancer Model Only)
Balancer Shaft Journal 2
Balancer Shaft Bearing 2
Balancer Shaft Journal 3 to Balancer Shaft
Bearing 3 (Balancer Model Only)
Balancer Shaft Journal 3
Balancer Shaft Bearing 3
Piston Pin Bore
Top Ring to Ring Groove
Second Ring to Ring
Groove
Oil Ring to Ring Groove
Top Ring
Second Ring
Item
Clearance
O.D.
I.D.
Clearance
O.D.
I.D.
I.D.
D1703-M-DI Clearance
D1803-M-DI
V2203-M-DI
V2403-M-DI
D1503-M-DI Clearance
D1503-M-DI-T
D1703-M-DI
D1803-M-DI
V2203-M-DI
V2403-M-DI
D1503-M-DI Clearance
D1503-M-DI-T
D1703-M-DI
D1803-M-DI
V2203-M-DI
V2403-M-DI
Ring Gap
D1503-M-DI Ring Gap
D1503-M-DI-T
D1703-M-DI
D1803-M-DI
V2203-M-DI
V2403-M-DI
Factory Specification
0.030 to 0.111 mm
0.00118 to 0.00437 in.
41.934 to 41.950 mm
1.65094 to 1.65157 in.
41.980 to 42.045 mm
1.65275 to 1.65531 in.
0.020 to 0.094 mm
0.00079 to 0.00370 in.
21.947 to 21.960 mm
0.86405 to 0.86456 in.
21.980 to 22.041 mm
0.86535 to 0.86775 in.
25.000 to 25.013 mm
0.98425 to 0.98476 in.
0.050 to 0.090 mm
0.0020 to 0.0035 in.
0.093 to 0.128 mm
0.0037 to 0.0050 in.
0.050 to 0.090 mm
0.0020 to 0.0035 in.
0.020 to 0.060 mm
0.0008 to 0.0021 in.
0.030 to 0.070 mm
0.0012 to 0.0028 in.
0.20to 0.35 mm
0.0079 to 0.0138 in.
0.30 to 0.45 mm
0.0118 to 0.0177 in.
0.40 to 0.55 mm
0.0157 to 0.0217 in.
0.35 to 0.50 mm
0.0138 to 0.0197 in.
S-11
DIESEL ENGINE
Allowable Limit
0.2 mm
0.0079 in.
–
–
0.2 mm
0.0079 in.
–
–
25.05 mm
0.9862 in.
0.2 mm
0.0079 in.
0.2 mm
0.0079 in.
0.2 mm
0.0079 in.
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
1.25 mm
0.0492 in.
1.25 mm
0.0492 in.
1.25 mm
0.0492 in.
1.25 mm
0.0492 in.
W1013874
KiSC issued 10, 2009 A