Xerox 5915 Service Manual page 24

STATUS
NAME
CODE
C1-2 TRAY 1 MIS FEED JAM
C9-3 MSI MISFEED JAM
E1-1 FUSER EXIT SWITCH ON CHECK JAM
E1-2 REGI-GATE SENSOR OFF CHECK JAM
E1-6 REGI-GATE SENSOR STATIC JAM
E3-3 FUSER EXIT SWITCH OFF CHECK JAM
E3-6 FUSER EXIT SWITCH STATIC JAM
E5-1 FRONT INTLK OPEN FAIL
E6-1 R/H UPPER INTLK OPEN FAIL
J1-1 TONER EMPTY FAIL
J1-2 TONER LIFE END
J3-1 DRUM UNIT SET FAIL
J3-2 Toner Cartridge SET FAIL
J3-3 Counter SET FAIL
J6-1 DRUM UNIT ID FAIL
J6-2 Toner Cartridge ID FAIL
J6-3 Counter ID FAIL
J7-1 DRUM UNIT LIFE END
J8-1 DRUM UNIT TYPE NO. FAIL
J8-2 Toner Cartridge TYPE NO. FAIL
J8-3 Counter TYPE NO. FAIL
J9-1 DRUM UNIT ID No. FAIL
J9-2 TONER UNIT ID No. FAIL
J9-3 TOTAL COUNTER ID No. FAIL
2-15
PROBLEM
Regi-gate Sensor isn't turned on within 2.7sec. after paper starts to be fed.
Regi-gate Sensor isn't turned on within 2.3 sec. after paper starts to be fed.
Fuser Exit Switch isn't turned on within 3.7 sec. After Regi-Gate is open.
Regi-Gate Sensor isn't turned off (remains ON) a preset period of time (which varies with paper
sizes) after Regi-Gate is open.
Regi-Sensor is on during Power On or Stand-by. (Paper remains)
Fuser Exit isn't turned off (remains ON) a preset period of time (which varies with paper sizes) after
Fuser Exit Switch is turned on.
Fuser Exit Switch is on during Power On or Stand-by. (Paper remains)
Front Cover is open, or Front Interlock Switch is defective.
R/H Upper Cover is open, or R/H Upper Interlock Switch is defective.
Number of copies reaches 100 after toner empty sensor sensed toner end condition.
The counter value of toner unit reaches the default value 7700.
Drum unit is not set, or is set incorrectly to the machine.
Toner unit is not set, or is set incorrectly to the machine.
Total counter is corrected improperly.
Drum unit Read/Write is in error.
Toner unit Read/Write is in error.
Total Counter Read/Write is in error.
Copy Value has become 50K (sheets of paper)
Type No. stored in ID of Drum Unit is not the same as that stored in NVM of the Main PWB.
Type No. stored in ID of Toner Unit does not match with that saved in NVM on main PWB.
Type No. stored in ID of Total Counter does not match with that saved in NVM on main PWB.
Identification No. of Drum Unit is not of Xerox origin.
Identification No. of Toner Unit is not of Xerox origin.
Identification No. of Total Copy Count is not of Xerox origin.
CORRECTIVE ACTION
• Refer to the MISFEED JAM.
• Refer to the MISFEED JAM
• Refer to BSD Sheet 5
• Refer to BSD Sheet 5
• Remove the paper
• Check the Regi-Gate sensor circuit.
• Refer to BSD Sheet 5
• Remove the paper
• Check the Fuser Exit Switch circuit.
• Close Front Cover.
• Check the Front Interlock Switch circuit.
• Check R/H Upper Cover.
• Check the R/H Upper Interlock switch circuit.
• Supply toner.
• Check the Toner Empty Sensor circuit.
• Replace the Toner Cartridge.
• Ensure to install the Drum Unit to the machine
properly
• Ensure to install the Toner Unit to the machine
properly
• Ensure to install the Total Copy Count Unit to
the machine
• Replace the Drum Unit.
• Replace the Toner Unit.
• Replace the Total Copy Count Unit.
• Replace the Drum Unit.
• Replace with correct type Drum Unit
• Replace with correct type Toner Unit
• Replace with correct type Total Copy Count
Unit
• Replace with Xerox Drum Unit
• Replace with Xerox Toner Unit
• Replace with Xerox Total Copy Count Unit
2.3 Level 1 Troubleshooting
Section 2 Troubleshooting
REF.
BSD
4
4
5
5
4
5
5
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5