Your 1 Year Guarantee Your appliance carries a 1 year parts and labour warranty. To fulfil the conditions of your guarantee, the appliance must be correctly installed, operated in accordance with the instructions and only be used for normal domestic purposes. Please note that the guarantee and service availability only apply to the United Kingdom mainland.
At time of delivery • Check the packaging and dishwasher immediately for signs of transport damage. If the appliance is damaged, do not put it into use but contact your supplier or customer service department. • Check you have received all the components required for the installation of this appliance: 2 x sealed 2 x plastic...
Safety Information During installation Site the dishwasher and connect it up in accordance with the installation instructions. The dishwasher must not be connected to the electricity supply whilst installation is being carried out. Ensure that the domestic wiring is properly earthed. The mains electricity supply must conform to the details shown on the dishwasher rating plate.
Consult the section entitled “Troubleshooting” at the back of the manual. If you cannot solve the problem, contact a service centre. Only specialised engineers are authorised to make repairs. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Installation Positioning the appliance Position the appliance in the desired location. The rear of the appliance should rest against the wall behind it and the sides, along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can be positioned to the left or the right to facilitate installation.
Adjustable screw Cold water connection If the water pipes are new or have not been used for some time, let the water run to make sure that the pipe is clear and free from impurities. Failing to do so may result in the water inlet becoming blocked and the appliance may be damaged as a result.
attached to the water supply tap as shown in fig 2. No other type of connection is acceptable. The water supply hose must not, under any circumstances, be cut as it contains electrical parts which are live. If the hose length is not adequate to make a proper connection, the hose must be replaced with one which is long enough.
Electrical Connection (UK ONLY) For your safety, please read the following information. Warning: This appliance must be earthed. This appliance must be connected to a 220-240 volts, 50Hz cycle AC supply by means of a three pin socket, suitably earthed and should be protected by a 13 amp fuse. This appliance is supplied with a rewireable 13 amp, 3-pin plug fitted with a 13-amp fuse.
The maximum dimensions and weight for the décor door are as follows: Height: 725mm Width: 598mm Thickness: 20mm Weight: The following steps should be taken to fit the décor door: Measure the width of the décor door Align the top of the template (supplied) with the top of the rear side of the décor door.
Sealed plug location Fig 12a The dishwasher should be secured to the underside of the worktop via the two fixing holes in the top trim. For non-wooden worktops (e.g.; marble) two solid worktop fixing brackets are provided to allow the appliance to be secured to the sides of the adjacent cabinets. These should be secured to the appliance using the two screws at the top of the chassis (see fig 1B), adjusted to the correct width and then screwed to the adjacent side panels using suitable screws.
Installing the plinth Position the dishwasher in the cut out in the kitchen cabinet. Install the continuous plinth according to the manufacturer’s instructions. Slowly open the dishwasher door to see if it interferes with the plinth. If so, rest the bottom edge of the décor door panel against the plinth and mark the area to be cut.
Getting to know your dishwasher Upper Rack Washing Filter Lower Rack Detergent and Rinse Aid Dispenser Top Spray Arm Water Inlet Hose with Aquastop Silverware Basket Drain Hose Bottom Spray Arm Power Supply Cord Salt Container Cap...
The default setting of the water softening system is “ - “. If using multi-functional tablets, fill the salt dispenser and set the adjuster to “ - “. If the hardness of the water is greater than 60° fH , set it to “ + “.
End of programme • Six beeps will indicate that the wash cycle has finished and all the programme indicators will illuminate. Switching the dishwasher off Several minutes after the programme has ended: • Open the door • Press the on / off button to switch the appliance off •...
Half load function The half load button “C” makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and energy consumption. To select ½...
Appliance365 End User Warranty Conditions The conditions below outline the prerequisites and scope of the warranty offered by Appliance 365 Limited (“we / us”) to consumer end users of appliances supplied by or through us. Please note that these conditions do not affect your statutory rights or the obligations of your retailer and your contract with them.
be complete. A purchase receipt with date of purchase or delivery must be presented prior to commencement of any repair or replacement. Replaced parts pass into our ownership. Service may not be available in all of the islands around the UK and Ireland. Please check with your retailer or contact our customer service department.
Note: Consistent with our continuing product development policy, improvements may have been made which render the contents of this package slightly different to that shown. Model No. UDW603 November 2009 Appliance 365 Limited Cranage House 730 Mandarin Court Centre Park...