Canon LaserBase MF3220 Series Service Manual page 110

Chapter 5
Error Code
0030
0031
0032
0033
0039
001F
003F
0040
0041
0042
0043
0044
0047
0048
004B
004C
004E
004F
0050
0051
0053
0054
0055
0056
0058
005A
005B
005C
005D
005E
005F
0060
0061
0062
0063
0064
0065
0066
0069
0070
0071
0080
0081
0082
0083
0084
0085
0086
0087
0088
008B
008C
008D
008F
0090
0091
0093
0094
0095
0096
009A
009D
009E
00A0
00A1
5-2
Description
Can't receive any signal within 6 sec. At phase D.
Received incorrect signal at phase D (not EOP, MPS, EOM, DCN, PPS_Q, PPS_Q,etc)
Can't receive carrier within 6 sec after sending MCF or RTP, RTN signal
Received DCN signal at ohase D within pages (not last page).
In non_ECM mode, when machine alredy received the data dosen't receive 13.1 seconds
Can't detect any G3 signal within 35 sec after sending DTC signal
Remote side TSI not define in machine one touch or speed dial directory
Can't receive carrier within 6 sec. after sending CTR.
Can't receive carrier within 6 sec. after sending PPR.
Can't receive correct signal after sending RNR signal
Receive incorrect signal at phase D in ECM mode.
Can't receive carrier/FSK signal within 6 sec. After sending MCF. ln ECM mode.
Can't receive correct signal or DCN received after sending ERR signal.
Can't receive correct signal after receive PPS_PRI_Q
Can't detect correct FSK signal even through detected FSK tone within 6 sec.
Handshake fail during re-train or between page in V34 Rx.
Receive DCN signal after sending DIS in V.34.
Remote side disconnected after sending ANSam in V.8 phase.
Can't receive any correct signal after detected CJ signal in V.8 phase.
Can't receive phase 3 signal after phase 2 within 20 seconds in V.34.
Modem disconnect after phase 4 in V.34.
Remote side disconnect after phase 4 in V.8
Receive incorrect signal after sending DIS signal in V.34
Modem disconnect after sending CFR in V.34
Can't detect image signal within 6 sec after modem enter to primary phase in V.34
Modem cannot detect any correct ECM frame with 3 minutes in phase C.
Modem can't detect control channel with 12 sec in phase C
Detect busy tone within control channel after phase C.
Modem can't detect any correct ECM frame with 12 sec in phase C.
Can't detect control channel signal after received RCP frame within 6 sec
Can't detect silence after sending JM signal for polling TX function.
There are no any bullietin files to be polled in V.34.
Machine cannot detect V.21 or V.8 signal with 35 sec.
Modem disconnect in phase D after our side sending out flags sequence in control channel.
Can't receive any flag sequence in control channel within 25 sec in phase D.
Can't detect any control channel signal in phase D within 60 sec even through energy still on the
line.
Can't detect any control channel signal within 60 sec after detect sillence in phase D.
Can't receive T.30 signal or carrier after sending CFR in V.34.
Capability no match paper size after received is DCS signal.
User press stop key within receiving.
Memory full within receiving.
Can't detect any G3 signal within 35 sec. specified by ITU-T in phase B.
Received DTC signal in transmission phase.
Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B.
Detected FSK signal, but Can't receive any signal within 35 sec.
Detect DCN signal in phase B.
Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC
Detected responds signal other than DTC,DIS,FTT,DCN or CFR after sending DCS.
Training attempt has failed because speed unit can't adjust to low lower speed.
Received DCN signal after sending out DCS signal
Receivers protcol of DIS is received, but it is not compatible with our machine.
Remote side or our side not support capability.
Receivers protocol of DIS is received, but remote side can't receive document temporary, may
because by run out of paper or other reason.
Modem not ready to received V.34 data within 6 sec after received CFR signal.
Called side document not ready for our polling.
Can't receive any commabd after send DCN signal 3 times consecutively
Received DCN signal after sending out DCN signal
Time out during transmit ECM frame or RCP command.
Wrong ID number
SUBADDRESS/PASSWORD capability not match in polling Rx mode.
Can't detect any signal after sending CI signal.
Remote side hang up before V.34 modem enter phase 2 state in V.34 polling Rx.
Manual Tx over 15 minutes whin in phase C by non-ECM mode.
User stop or cancel transmission job.
Document JAM within transmission