Function Keys - DSC PC5015 Installation Manual

K E Y
• • • • • [6] – User Initiated Call-Up [6] – User Initiated Call-Up [6] – User Initiated Call-Up [6] – User Initiated Call-Up [6] – User Initiated Call-Up
When [6] is pressed, the panel will initiate a call to the downloading computer.
LCD Keypad User Functions
Additional features are available using on the LCD keypad. These features do not have numbers
assigned. Use the arrow keys (< >) to scroll through the [ ] [6] menu and press the [ ] key to select the
following commands.
• View Event Buffer View Event Buffer View Event Buffer: The 128 Event Buffer can be viewed through any LCD keypad (See Section 5.16.1 View Event Buffer
View Event Buffer
"Viewing the Event Buffer Through the LCD Keypad") .
• Brightness Control Brightness Control: When this option is selected the keypad will allow you to scroll through 10 different Brightness Control Brightness Control Brightness Control
backlight level options. Use the arrow keys (<>) to scroll to the desired backlight level and press the
[#] key to exit.
• Contrast Control Contrast Control Contrast Control: When this option is selected the keypad will allow you to scroll through 10 different Contrast Control
Contrast Control
contrast level options. Use the arrow keys (<>) to scroll to the desired contrast level and press the [#]
key to exit.
Keypad Buzzer Control Keypad Buzzer Control
• Keypad Buzzer Control Keypad Buzzer Control: When this option is selected the keypad will allow you to scroll through 21 Keypad Buzzer Control
different keypad sounder tone options. Use the arrow keys (<>) to scroll to the desired keypad beeper
level and press the [#] key to exit. This function can be achieved on LED keypads by holding the [ ] key.
[ ] [7] Command Output Functions
There are four output functions available to the user. Entering [ ] [7] [1-4] [Access Code, if required] will
activate any output programmed for options [19]-[22] (respectively). Each function can be performed
when the system is either armed or disarmed.
For more information regarding these output types, see Section 5.10 "PGM Output Options."
[ ] [8] Installer Programming
Enter [ ][8] followed by the Installer Code to enter Installer Programming (See Section 4.0 "How to Program").
[ ] [9] Arming Without Entry Delay
When a Partition is armed with the [ ][9] command the panel will remove the entry delay from the
partition. After the exit delay, Delay 1 and Delay 2 type zones will be instant and Stay/ Away zones will
remain bypassed. (See Section 5.1 "Zone Definitions").
For more information regarding this feature, see the PC5015 Instruction Manual ("Alternate Arming
Methods – Arming Without Entry Delay").
The entry delay can be activated/deactivated at any time while the system is armed by pressing [ ][9].
[ ] [0] Quick Arm
If the Quick Arm Enable option is enabled the panel can be armed by entering [ ][0]. This is a useful
method of arming a Partition when someone without a access code will be required to arm a Partition.
The Quick Arm feature must be enabled in order for the Stay/Away function keys to operate as
intended. If the feature is not enabled, the user will be required to enter their access code after
pressing the Stay or Away function key in order to arm the system in the stay or away mode.
[ ] [0] Quick Exit
Quick Exit will allow someone to leave an armed premise through a Delay type zone without having to
disarm and rearm the system.
When [ ][0] is entered, if the Quick Exit Enabled option is enabled, the panel will provide a two minute
window to exit. During this time the panel will ignore the first activation of a Delay type zone. When the
Delay zone is secured the panel will end the two minute time period.
If a second Delay zone is tripped, or if the zone is not restored after two minutes, the panel will start entry delay.
If Quick Exit is used on a partitioned system, Keypad Blanking and Access Code Required to Remove
Blanking should be enabled.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Quick Arm Enable ................................................... Section [015], Option [4]
Quick Exit Enable ................................................... Section [015], Option [3]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3.5

Function Keys

There are five function keys on the PC5015 keypads labelled Stay, Away, Chime, Reset and Exit. The operation
of these keys is described below. The function is activated by pressing and holding the key for 2 seconds.
"Stay" - Stay Arm
Arms the partition to which the keypad is assigned. All Stay/Away type zones will be automatically
bypassed. Delay type zones will provide entry and exit delay. The Quick Arm feature must be enabled for
this key to function (Section [015], Option [4]) . If Quick Arming is not enabled, the user must enter their
access code after pressing the function key in order to arm the system in the Stay mode.
"Away" - Away Arm
P A D C O M M
17
A N D S