DSC PC5015 Installation Manual page 19

K E Y P
A Fire zone trouble will be generated and displayed in the armed state. A Fire zone trouble will
also restart the trouble beeps from all keypads.
6 Zone Tamper: A zone configured for Double End Of Line resistor supervision has a tamper condition,
or the tamper switch is open on a wireless device. When a tamper condition occurs, the keypad(s) will start
to beep (if the system is armed, an alarm will occur). Press [6] while in the Trouble mode to view the
affected zones. If a zone is tampered or faulted, it must be fully restored to clear the trouble.
7 Device Low Battery: A wireless device has a low battery condition. Press [7] one, two, or three times
to view which devices are experiencing battery failure. An LED keypad will indicate battery failure
using zone lights 1 to 8. The following will occur:
Press [7]
Press [7] again
Press [7] again
8 Loss of System Time: When the panel is powered up, the internal clock needs to be set to the correct
time. This trouble is cleared when an attempt is made to reset the clock.
[ ] [3] Alarm Memory
The 'Memory' light will be on if any alarm occurred during the last armed period or if an alarm occurred
while the panel was disarmed (24 hour zones). Instructions on viewing alarms in memory are located in
the PC5015 Instruction Manual ("Disarming the System").
[ ] [4] Door Chime On/Off
If enabled the keypad will beep 5 times rapidly when a zone is tripped and restored. The panel will only
do this for zones with the Door Chime attribute enabled and if the door chime feature is enabled (See
Section 5.2 "Zone Attributes") . The door chime feature is explained in greater detail in the PC5015
Instruction Manual ("Door Chime Feature").
[ ] [5] Programming Access Codes
All 37 access codes are programmed in this section. For instructions on programming access codes, see
the PC5015 Instruction Manual ("Programming Access Codes").
[ ] [6] User Functions
To program user functions, perform the following:
1. Press [ ] [6] [Master Code]. The keypad will flash the 'Program' light.
2. Press the number [1] to [5] for the item to be programmed.
• • • • • [1] - Time and Date [1] - Time and Date [1] - Time and Date
[1] - Time and Date [1] - Time and Date
See the PC5015 Instruction Manual for instructions on setting the time and date ("Setting the Time and Date").
• • • • • [2] - Auto-Arm Enable/Disable [2] - Auto-Arm Enable/Disable [2] - Auto-Arm Enable/Disable [2] - Auto-Arm Enable/Disable [2] - Auto-Arm Enable/Disable
Enter [ ] [6] [2] to enable (three keypad beeps) or disable (one long beep) the auto-arm feature.
• • • • • [3] - Auto-Arm Schedule [3] - Auto-Arm Schedule [3] - Auto-Arm Schedule [3] - Auto-Arm Schedule [3] - Auto-Arm Schedule
Enter [ ][6][3] to change the auto-arm time for each day of the week.
Scroll to the day of the week you want to change, or enter the number of the day (1-7 for Sunday to
Saturday). On an LED keypad zone lights 1-7 will represent Sunday to Saturday.
When you have selected a day, enter the auto-arm time in 24-hour format (i.e. enter a 4-digit number in
[hhmm] format).
The system will return you to the day selection menu. Scroll to the next day you want to program, or to
exit auto-arm programming, press [#].
Only LCD5500 v2.0 or greater keypads support the [ ][6][3] menu option.
• • • • • [4] - System Test [4] - System Test [4] - System Test [4] - System Test [4] - System Test
When [4] is pressed the panel will perform the following. For step-by-step instructions on performing a
system test, see the PC5015 Instruction Manual ("Full System Test"):
- sound the alarm output for two seconds
- light all lights on the keypad
- sound the keypad buzzer for two seconds
- test the main panel / PC5204 battery
- send a System Test Reporting code, if programmed (See Section 5.7 "Communicator - Reporting Codes") .
• • • • • [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading)
When [5] is pressed the panel will turn on the downloading option for 6 hours. During this time the panel
will answer incoming downloading calls (See Section 5.8 "Downloading") .
A D C
# of Keypad displays
beeps
1 Zones with low batteries (LED keypad - zone lights 1 to 8)
2 Handheld keypads with low batteries (LED keypad - zone lights 1 to 4)
3 Wireless keys with low batteries (LED keypad - zone lights 1 to 8). To view the
battery conditions of wireless keys 9 through 16, you must use an LCD keypad.
16
O M M A N D S