Function Keys - DSC Power632 PC1565 Installation Manual

time, the panel will answer incoming downloading calls
(see section 5.10 "Downloading" on page 20).
• [6] – User Initiated Call-Up
When [6] is pressed, the panel will initiate a call to the
downloading computer.
Additional Features Available from the LCD Keypad
Additional features, including access to the event buffer, are
available using the LCD keypad. Use the arrow keys (< >) to
scroll through the [*][6] menu and press the [*] key to select
the following commands:
Viewing the Event Buffer from an LCD Keypad
Select "View Event Buffer" from the [*][6] menu. The keypad
will display the event, event number, time and date along with
the zone number and access code, if applicable. Press [*] to
toggle between this information and the event itself. Use the
arrow keys (<>) to scroll through the events in the buffer.
When you have finished viewing the event buffer, press [#] to
exit.
Brightness Control
You can select from 10 different backlighting levels. Use the
arrow keys (< >) to scroll to the desired backlighting level.
Press [#] to exit.
Contrast Control
You can select from 10 different display contrast levels. Use
the arrow keys (< >) to scroll to the desired contrast level.
Press [#] to exit.
Keypad Sounder Control
You can select from 21 different keypad tones. Use the arrow
keys (< >) to scroll to the desired keypad sound level and
press [#] to exit. This feature can be accessed on LED key-
pads by pressing and holding the [*] key.
[*][7] Command Output Functions
The user can activate programmable output functions using
the [*][7][1-2] commands. The outputs may be activated when
the system is either armed or disarmed.
[*] [7] [1] – Command Output Option #1:
Press [*] [7] [1] [Access Code, if required] to activate outputs
programmed as PGM output option [19]. This output can be
used for operating devices such a garage door opener, light-
ing or door strikes.
[*][7][2] – Command Output Option #2:
Press [*][7][2][Access Code, if required] to activate all outputs
programmed as one of PGM output options [03] or [20].
Special Note: Traditionally, [*][7][2] has been reserved for
resetting smoke detectors. Smoke detectors should now be
programmed as output [03] "Sensor Reset". If using output
option [03], do not program [20] Command Output Option #2.
Please see section 5.11 "PGM Output Options" on page 21 for
more information.
[*][8] Installer's Programming
Enter [*][8] followed by the Installer's Code to access
Installer's Programming. See sections 4 and 5 for more infor-
mation.
[*][9] Arming Without Entry Delay
When the system is armed with the [*][9] command, the panel
will cancel the entry delay. Delay 1 and Delay 2 type zones will
be instant and Stay/Away zones will be bypassed as soon as
the exit delay has ended (see section 5.2 "Zone Program-
ming" on page 15). The user must enter a valid access code
after pressing [*][9].
K e y p a d C o m m a n d s :
[*][0] Quick Arm
If the Quick Arm option is enabled, enter [*][0] to arm the
panel without an access code (See section 5.17 "Arming/Dis-
arming Options" on page 24).
NOTE: Quick Arm cannot be used to cancel auto arm.
[*][0] Quick Exit
The Quick Exit function, if enabled, will allow someone to
leave an armed premises through a Delay type zone without
having to disarm and re-arm the system (See section 5.17
"Arming/Disarming Options" on page 24).
When [*][0] is entered, the panel will provide a two minute win-
dow for the user to exit the premises. During this time, the
panel will ignore only one activation of a Delay zone. When the
Delay zone is secured, the panel will end the two minute quick
exit delay.
If a second Delay zone is tripped, or if the zone is not restored
after two minutes, the panel will begin the entry delay.
NOTE: If the Exit Delay is in progress, performing a Quick Exit
will not extend the Exit Delay.
3.6

Function Keys

There are five function keys on each keypad labelled Stay, Away,
Chime, Reset and Exit. Each key is programmed by default to
perform one of the functions described below. Press and hold
the appropriate key for two seconds to activate a function.
NOTE: On the PC1555RKZ keypad, use number keys 1 - 5 for
the function keys.
"Stay" – (03) Stay Arm
The system will arm in the Stay mode (see section 3.2 "Auto
Bypass – Stay Arming" on page 8). Enable the Quick Arm fea-
ture (programming section [015], option [4]) to have this key
function without the need to enter an access code. If Quick
Arm is not enabled, the user will have to enter an access code
before the system will stay arm.
"Away" – (04) Away Arm
The system will arm in the Away mode (see section 3.2 "Auto
Bypass – Stay Arming" on page 8). Enable the Quick Arm fea-
ture (programming section [015], option [4]) to have this key
function without the need to enter an access code. If Quick
Arm is not enabled, the user will have to enter an access code
before the system will away arm.
"Chime" – (06) Door Chime On / Off
The Door Chime feature will turn ON or OFF (see "[*][4] Door
Chime On/Off" on page 10).
"Reset" – (14) Sensor Reset or [*][7][2]
The panel will activate all PGM outputs programmed as option
[03] Sensor Reset or [20] Command Output Option #2. (See
"[*][7] Command Output Functions" on page 11).
"Exit" – (16) Activate Quick Exit
The panel will activate the Quick Exit feature (See section 3.5
"[*] Commands" on page 8).
Additional Function Key Options
The programming of any function key on any keypad may be
changed to one of the options listed below. (See section 2.5
"Keypad Assignment" on page 4 for instructions on changing
function key programming.) Each option is listed according to
the programming code, followed by the corresponding [*] key
command. For more information regarding each function,
please refer to the appropriate part of section 3.5 "[*] Com-
mands" on page 8.
3 . 6 F u n c t i o n K e y s
11