Settings For External Equipment; Information On Dv Dubbing - FUNAI WL6D-M102 Owner's Manual

Settings for External Equipment

Video Colour System
When you record from external equipment or copy a
videotape to a DVD disc, you can set the format Auto, PAL or
SECAM.
1
In stop mode, press [SETUP]. Select "General
Setting" using [K \ L], then press [ENTER].
2
Select "Recording" using [K \ L], then press
[ENTER].
3
Select "Video Colour System" using [K \ L],
then press [ENTER].
4
Select "Auto", "PAL" or "SECAM" using [K \ L],
then press [ENTER].
General Setting
Playback
Auto Chapter
Display
Recording Audio Select (1H)
Video
Auto Finalise
Recording Video Colour System
Aspect Ratio (Video mode)
Clock
Auto
Dubbing Mode
DivX
PAL
Bilingual Recording Audio
HDMI
SECAM
External Input Audio
Reset All
Video Colour System
Auto: The video colour system will be set
automatically according to the recording
material.
PAL: The video colour system will be set to PAL.
SECAM: The video colour system will be set to
SECAM.
5
Press [SETUP] to exit.
Note
• During recording, when a signal other than PAL or SECAM
is detected, an error message appears on the screen and
recording will be paused. Recording will be resumed when a
PAL or SECAM signal is detected.
Recording from External Equipment
Video VR
DVD-RW DVD-RW DVD-RW DVD-RW DVD-RW DVD-RW
Before recording from external equipment, see page 19 for
connection instructions.
1
Turn on the TV and be sure to select the input to
which the unit is connected.
2
When you want to record to the disc:
Press [DVD].
Press [OPEN\CLOSE EJECT A] to open the
disc tray, then place the disc to record on.
Press [OPEN\CLOSE EJECT A] again to close
the disc tray.
30
EN
VCR VCR
DVD-R DVD-R DVD-R
When you want to record to a videotape:
Press [VCR].
Insert a videotape with a record tab into the
cassette compartment.
3
Select the input terminal to which the external
equipment is connected (AV1 or AV2).
Press [AUX G \ H] repeatedly to select AV1 or AV2.
4
Select a recording speed using [REC SPEED].
Refer to "Recording Speed" on page 21 for DVD or page
62 for VCR.
5
Press [RECORD I] (DVD / VCR) on the unit to
start recording.
6
Press the [PLAY B] button on the external
equipment.
7
For disc:
Press on the unit to stop
[STOP C]
recording.
For videotape:
Press
[STOP\EJECT C A]
recording.
Note
• During recording, recording will be paused when a signal
other than PAL or SECAM is detected. (See "Video Colour
System" on page 30 for details.)
• The signal from the external device will be output automatically
when the TV is connected to AV1 and the external device is
connected to AV2 using a Scart cable with its power on.
(However, it will not be output when this unit's power is turned off.)
If you want to monitor this unit's signal, press [DISPLAY]
or turn the external device off. (The signal from this unit can
only be monitored during playback.)
If you want to monitor the signal from other input, press
[DISPLAY], then select the desired input channel using
[AUX G \ H].

Information on DV Dubbing

This function helps you to dub the contents in the DVC (digital
video camcorder) to DVD or VCR easily. (See page 63 for
DVC to VCR Dubbing.)
You can control basic operations of the DVC from the remote
control of this unit if the DVC is in video mode.
Guide to DV and On-Screen Display
1
Connect your DVC to the DV-IN jack on the front
panel using a DV cable. (Use the DV cable that
has 4-pin input jack and is compliance with the
IEEE 1394 standards.)
2
Press [AUX G \ H] repeatedly to select
DV(AV3).
on the unit to stop