Regency PTO30CFT Owners & Installation Manual

Regency plateau series outdoor decorative gas appliances
Hide thumbs Also See for PTO30CFT:

Advertisement

Quick Links

Regency Plateau
Outdoor Decorative Gas Appliances
www.regency-fire.com
WARninG:
if the information in these instructions
are not followed exactly, a fire
or explosion may result causing
property damage, personal injury or
loss of life.
WARninG:
improper installation, adjustment,
alteration, service or maintenance
can cause injury or property damage.
Read the installation, operating and
maintenance instructions thoroughly
before installing or servicing this
equipment.
installation and service must be
performed by a qualified installer,
service agency or the gas supplier
Tested by:
fpi fiREpLACE pRoduCts intERnAtionAL Ltd. 6988 Venture st., delta, BC Canada, V4G 1H4
919-013
WARninG - foR YouR sAfEtY
What to do if you smell gas:
•shut off gas to the appliance.
•do not try to light any appliance.
•Extinguish any open flame.
•if odor continues, keep away from the appliance and im-
mediately call your gas supplier or fire department.
•do not touch any electrical switch: do not use any phone
in your building.
•immediately call your gas supplier from a neighbour's
phone.
•follow the gas supplier's instructions.
•if you cannot reach your gas supplier, call the fire
department.
WARninG:
do not store or use gasoline or other flammable vapours
and liquids in the vicinity of this or any other appliance.
A Lp-cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
Installer: please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: please keep these instructions for future reference.
Series
WARninG: FOR OutDOOR uSe Only
owners &
installation Manual
MODELS: PTO30CFT
PTO30IST
PTO30CKT
07/21 /11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PTO30CFT and is the answer not in the manual?

Questions and answers

Summary of Contents for Regency PTO30CFT

  • Page 1 & installation Manual Regency Plateau Series ™ MODELS: PTO30CFT Outdoor Decorative Gas Appliances PTO30IST PTO30CKT WARninG: FOR OutDOOR uSe Only www.regency-fire.com WARninG: WARninG - foR YouR sAfEtY if the information in these instructions What to do if you smell gas: are not followed exactly, a fire •shut off gas to the appliance.
  • Page 2 Congratulations! You are the owner of a state-of-the-art Outdoor Decorative Gas Appliance by REGEnCY . The ® Plateau™ Series Outdoor Decorative Gas Appliance has been designed to provide you with all the warmth and charm of a fire at the flick of a switch. The Plateau™ Series Outdoor Decorative Gas Appliance has been approved by Warnock Hersey/Intertek for both safety and efficiency.
  • Page 3: Table Of Contents

    Aeration Adjustment ............ 11 Wiring Diagram ............12 Caster installation ............13 Gas Connection ............14 Conversion from Ng to Lp..........15 LP Tank installation - Pto30cft only ......17 LP Tank Installation ............18 PTO30IST/PTO30CKT ONly ........18 LP Tank removal ............18 Switch connection............19 Battery Install ...............19 Table top Installation - coffee table unit .......20...
  • Page 4: Safety Label

    Commonwealth of Massachusetts. For the State of Massachusetts, flexible connec- tors shall not exceed 36 inches in length. For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 5: Unit Dimensions - Coffee Table

    - CoffEE tABLE 43”(1092mm) TOP VIEW 38”(965mm) 3-5/8”(91mm) 2-9/16”(64mm) 11LB TANK 11LB TANK FLOOR LEVEL 16-11/16”(423mm) 2-1/16”(52mm) 40-5/8”(1030mm) Floor to bottom END VIEW SIDE VIEW of LP tank nOTE: Optional glass surround shown Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 6: Unit Dimensions - Island Table

    6-3/16” (156mm) 28-7/8” (733mm) 1” 20lb tank 20lb tank (25mm) 40-3/8” 20-11/16” Floor level (1031mm) 3-1/8” (525mm) (79mm) Floor to bottom of LP tank nOte: For optional glass surround dimensions - see previous page. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 7: Unit Dimensions - Cocktail Table

    - CoCktAiL tABLE 2 " 16 " 1461mm 783mm TOP VIEW 16 " 16 " 963mm 325mm 8 " 4 " 1248mm 742mm SIDE VIEW END VIEW nOTE: Optional glass surround shown Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 8: Important Message

    State of 4) Inspect the burner before each use of the OtheR enclOSeD AReA. California to cause cancer, birth defects or appliance for blockage and any signs of other reproductive harm. deterioration. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 9: Installation Checklist

    At least 30% of the remaining wall area is open and unrestricted age is not the responsibility of the manufacturer. 30% or more in total of the remaining wall area is open and unrestricted. Open side at least 25% of total wall area Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 10: Minimum Clearances To Combustibles

    When using supplied leveling legs or optional casters. 1"(25mm) Unit Base to Floor : floor E: Alcove Width 84"(2134mm) Wall to Wall (Minimum) f: Alcove depth 60" (1524mm) Front to Back Wall (Maximum) notes: 0" no Hearth Required Alcove Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 11: High Elevation

    6) When finished reading manometer, turn off the controls is not covered under warranty. gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" flat screwdriver. Note: Screw should be snug, but do not over tighten. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 12: Wiring Diagram

    The AA batteries in the battery pack operate the burner switch. If the batteries become weak they will need to be replaced with quality alka- line batteries. This unit will not operate without AA batteries. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 13: Caster Installation

    1) Line up caster with existing nutsert on frame Allen key 3) After installation, lock out all 4 casters before assembling Nutsert Bottom of unit frame unit. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 14: Gas Connection

    If soap bubbles, this would indicate a gas leak. 5) Reverse steps 1 & 2. 2) Remove long side panel (left panel if you are facing end with ON/OFF switch) to access the 3/8" fitting to the gas control. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 15: Conversion From Ng To Lp

    3) Slide the burner to the left, away from the pilot assembly and lift out. 6) Re-install pilot cap. 7) Reinstall burner assembly. 8) Adjust aeration accordingly.- see aeration adjustment section manual for details. Burner orifi ce Pilot Cap Regency Plateau™ Series Outdoor Gas Fireplace 919-039 06/15/11...
  • Page 16 HI/LO pressure regulator 12) Attach the label “This unit has been converted to LPG” near or on top of the serial # decal. 13) Replace yellow “NG” label with red “LPG” label. Regency Plateau™ Series Outdoor Gas Fireplace 919-039 06/15/11...
  • Page 17: Lp Tank Installation - Pto30Cft Only

    Lp tAnk instALLAtion - pto30Cft onLY nOte: Max tank size 11lb. 1) Remove end panel (opposite end of switch panel),. 2) Remove long side panel (left panel if facing On/OFF switch end), to ac- cess the 3/8" fitting to the gas control.
  • Page 18: Lp Tank Installation

    Gas connection @ tank WARNING! When using a LP tank - a minimum 1”(25mm) gap must be maintained at all times, between the floor and base of unit. (Refer to owners manual) 919-031 Butterfly bolt Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 19: Switch Connection

    1) Remove left side (with switch assembly) end panel from unit. 2) Pull down battery compartment - located below the DFC panel. Battery compartment 2) Connect 2 wires to the switch. 3) Install 4 - AA batteries and reverse steps. 3) Replace panel. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 20: Table Top Installation - Coffee Table Unit

    These instructions apply to both the stainless steel and sunset 3) To remove - reverse steps. bronze table tops. 1) Place table top over completed unit. Final Install 2) Place end caps over pilot and opposite end to complete installation. End Caps Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 21: Table Top Installation

    4) Place the 8 fi ller brackets on the table top as shown - before installing tiles. NOTE: Filler brackets are used to fi ll the gaps between each tile. Filler Brackets 919-042 06/16/11 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 22: Glass Crystal Installation

    For Units HZI390E, HZI390EB only Glass Crystals shown on Burner Optional Ceramic Spa Stones shown on burner. For units P33S, P33SE, L676S, U32S, U32SE, E33S only For units P33S,P33SE L676S, U32S, U32SE, E33S only 918-753g 06/23/11 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 23: Optional Volcanic Stone Installation

    Volcanic Stones Ivory /Tan + Glass Crystals For the PTO30, PTO60 For the HZO42 & HZO42AUS & Plateau Series only only Volcanic Stones Slate /Grey + Glass Crystals For the HZO42 & HZO42AUS only 919-050 06/27/11 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 24: Optional Log Set Installation

    3) Install log E on the burner as shown below. Orient log E across log D in the same way and in a similar position as shown in Diagram 4. Diagram 4 919-009 04/01/11 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 25 6) Install log C on the left side of the burner as shown below. Orient log C in the same way and in a similar position as shown in Diagram 7. Diagram 7 Final Install Regency Plateau™ Series Outdoor Gas Fireplace 919-009 04/01/11...
  • Page 26: Optional Glass Surround Installation

    8) Apply the "caution hot" sticker to the outside of the glass surround. (Recommend the bottom left corner of the long p iece of glass). Repeat for the other side / sticker. 919-037 06/15/11 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 27: Riser Installation

    On the riser, remove panels by grasping bottom and lift backwards, place 4) Remove the 4 adjustable rubber feet form the bottom of the island unit on a soft clean surface. and transfer to the bottom of the riser. Knockouts Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 28 5) Install 12 screws in locations shown below to secure island frame to riser base. 5) Reinstall LP tank and reconnect or reconnect nG gas line. Reinstall panels, table top and glass surround and glass crystals to com- plete installation. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 29: Plateau Table Cover Installations

    Let the unit cool before installing the cover. 1) Place the weather cover over the entire table - when not in use. Turn off gas supply to unit before installing cover. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 30: Operating Instructions

    After approximately 2 seconds turn on ON/ OFF switch. c) Unit will repeat step 2. sHutdoWn pRoCEduRE 1) Turn ON/OFF switch. 2) If service is to be performed - you must discon- nect the battery pack. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 31: Copy Of Lighting Plate Instructions

    Appuyez sur le bouton ON / OFF Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction pour plus de détails. DO NOT REMOVE THIS INSTRUCTION PLATE 918-628b Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 32: Maintenance Instructions

    This is not covered under the terms of the warranty policy. 8) Verify operation after servicing. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 33: Switch Replacement

    1) Remove the end panel (side with switch assembly mounted on it) from unit. 2) Remove 2 wire from the switch. 3) Remove 2 screws from switch cover to release switch. 4) Replace switch and reverse steps. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 34: Valve Assembly Replacement

    4) Remove orange EV1 wire connected to the gas valve. 5) Remove green EV2 wire connected to the gas valve. 6) Remove HI/LO extension knob. Hi/Lo Extension ground Flame sensor 7) Remove 10 screws in locations shown below to remove valve tray. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 35: Digital Fireplace Control Replacement

    1) Remove left side (with switch assembly) end panel from unit. 2) Pull down battery compartment - located below the DFC panel. 3) Remove two screws to swing down DFC box. Battery compartment Battery pack 3) Replace 4 - AA batteries and reverse steps. Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 36: Parts

    Glass connectors 904-655 Orifice #45 - LP 904-952 nylon fastner 376-900 Table top frame 911-012 Ignition Board 376-902 Tile set - Slate 326-930 Log Set 376-903 Tile set - Brown 376-522 Island riser 919-013 Manual Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 37 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 38 Regency Plateau™ Series Outdoor Gas Fireplace...
  • Page 39: Warranty

    Quality Assurance team carefully inspects each unit thoroughly ® before it leaves our facility. fpi fireplace products international Ltd. is pleased to extend this limited warranty to the original purchaser of a Regency product. this warranty ®...
  • Page 40 & Address: ______________________________________________ ___________________________________________________________________ installer: ___________________________________________________________ phone #: ___________________________________________________________ date installed: ______________________________________________________ serial no.: __________________________________________________________ & Regency, Regency Plateau are registered trademarks of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2011, FPI Fireplace Products International Ltd. All rights reserved.

This manual is also suitable for:

Pto30cktPto30ist

Table of Contents