Regency HZO42-NG Owners & Installation Manual

Hzo42 outdoor gas fireplace

Advertisement

Regency HZO42 Outdoor
www.regency-fi re.com
WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapours and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can cause injury or property
damage. Read the installation, operating and maintenance instructions thoroughly before installing
or servicing this equipment.
918-976a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
Gas Fireplace
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Installation Manual
MODELS: HZO42-NG
LISTINGS AND CODE APPROVALS
These gas appliances have been tested
in accordance with AS4565 / NZS 4558
and have been certifi ed by the IAMPO
Oceana for installation and operation
as described in these Installation and
Operating Instructions.
Your unit should be serviced annually
by an authorised service person.
WARNING: FOR OUTDOOR USE ONLY
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fi re department.
Owners &
HZO42-ULPG
04/09/13

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HZO42-NG and is the answer not in the manual?

Questions and answers

Summary of Contents for Regency HZO42-NG

  • Page 1 Owners & Regency HZO42 Outdoor Installation Manual Gas Fireplace MODELS: HZO42-NG HZO42-ULPG LISTINGS AND CODE APPROVALS These gas appliances have been tested in accordance with AS4565 / NZS 4558 and have been certifi ed by the IAMPO Oceana for installation and operation as described in these Installation and Operating Instructions.
  • Page 2 Congratulations! ® You are the owner of a state-of-the-art Gas Fireplace by REGENCY . The HZO42 Outdoor fi replace has been designed to provide you with all the warmth and charm of a fi re at the fl ick of a switch.
  • Page 3: Table Of Contents

    Glass crystal / garden stone installation .....17 Pebble installation ............18 Volcanic stone installation ...........19 Optional Log Set Installation........20 Heat defl ector installation ..........22 Faceplate installation ...........23 Glass wind shield installation........24 Weather cover installation / removal ......24 Regency HZO42 (Aus) Gas Fireplace...
  • Page 4: Data Badge

    DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IN OPERATION. DO NOT OPERATE WITH PANELS, COVERS OR GUARDS REMOVED FROM THIS APPLIANCE. DO NOT ENCLOSE THIS APPLIANCE. DO NOT MODIFY THIS APPLIANCE. 908-602a Regency HZO42 (Aus) Gas Fireplace...
  • Page 5: Copy Of Data Badge

    DIMENSIONS UNIT DIMENSIONS 37 - 13/16” (960mm) 41 - 11/16” (1059mm) 43 - 11/16” (1110mm) 16 -1/2” (491mm) 43-1/4” (1099mm) 15 - 1/4” (387mm) 13 - 7/16” (341mm) 5/8” (16mm) Regency HZO42 (Aus) Gas Fireplace...
  • Page 6: Installation

    The appliance should be enclosed. LATED SPACE AND SHALL NOT BE USED IN A BUILDING, GARAGE OR ANY 4) Inspect the burner before each use of the appliance for blockage and any signs of OTHER ENCLOSED AREA. deterioration. Regency HZO42 (Aus) Gas Fireplace...
  • Page 7: Installation Checklist

    Open side at least 25% of total wall area In case of balconies, at least 20% of the total wall area shall be and remain open and unrestricted. Regency HZO42 (Aus) Gas Fireplace...
  • Page 8: Locating Your Gas Fireplace

    fi rebox opening. This will create a pressure zone • Only Regency approved media should be used in the fi rebox (i.e. at the fi rebox and will prevent the unit from venting stones/glass) •...
  • Page 9: Minimum Clearances To Combustibles

    Top of Fireplace Opening D: Mantel Depth (max.) 12" (304mm) From Wall E: Alcove Width 57"(1148mm) Wall to Wall (Minimum) F: Alcove Depth 36" (914mm) Front to Back Wall (Maximum) Notes: 0" No Hearth Required Alcove Regency HZO42 (Aus) Gas Fireplace...
  • Page 10: Framing Dimensions

    Metal Stud on edge Important Note: Two (2) ventilation grills are highly recommended for all enclosures. This is to alleviate moisture and allow for air to circulate. Minimum recommended size: 20" sq (508 mm²) ea. Regency HZO42 (Aus) Gas Fireplace...
  • Page 11: Mantel Clearances

    (On Edge) 26-1/2”(673mm) 10” (254mm) Non-combustible Facing 18” (457mm) 11” (279mm) Standoff To Unit 23”(584mm) Base Top of Fireplace Opening NON-COMBUSTIBLE REQUIREMENTS 43-11/16” (1110mm) Non-combustible Material 38-1/16” (767mm) Non-combustible Material 2-7/8” 6-9/16” ( 3mm) (167mm) Regency HZO42 (Aus) Gas Fireplace...
  • Page 12: Finishing

    For facing material is over 1” (25mm)thick, use the outer cut out for your faceplate template. (1022mm) 40 1/4” HZO42 For facing material is under 1” (25mm) thick, use the inner cut out to keep construction material out of the fi rebox. 38” Regency HZO42 (Aus) Gas Fireplace...
  • Page 13: Gas Line Installation

    6) When fi nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" fl at screwdriver. Note: Screw should be snug, but do not over tighten. Regency HZO42 (Aus) Gas Fireplace...
  • Page 14: Unit Assembly Prior To Installation

    Factory Set Depending on the material used for fi nishing, the nailing strips must be set accordingly so that the fi nished material is always at the 1-1/2" (38mm) edge of the fl ange. Unit Regency HZO42 (Aus) Gas Fireplace...
  • Page 15: Wall Switch Installation

    (Two-Wire) When Using Wall Thermostat (CP-2 System) Wire Size Max. Length 14 GA. 15.24m 16 GA. 9.75m 18 GA. 6.09m 20 GA. 3.65m 22 GA. 2.74m CAUTION Do not wire millivolt wall switch wires to 240V wire. Regency HZO42 (Aus) Gas Fireplace...
  • Page 16: Wiring Diagram

    Profl ame SureFire™ Switch 0.886.001 Proflame Valve Standard Main On/Off Switch Standard Wall Switch or Optional Wall Switch Remove the protective coating from the following components before proceeding. Carefully follow stainless handling instructions on following page. Regency HZO42 (Aus) Gas Fireplace...
  • Page 17: Inner Panel Installation

    2) Install a side panel next (not important which side goes in fi rst). Position the panel with the bend in the panel facing towards the outside or wall of the unit. Position side panel and secure with a clip and one screw. Regency HZO42 (Aus) Gas Fireplace...
  • Page 18: Glass Crystal / Garden Stone Installation

    ** Recommended - use only 40 of the 70 ceramic stones on the HZ30E burner. *** Recommended - use only 24 of the 70 ceramic stones on the HZI234E burner. OPTIONAL PEBBLES / GLASS CRYSTAL INSTALLATION Glass Crystals shown on Burner HZO42 (AUS) PTO30, PTO60, Plateau Series only Regency HZO42 (Aus) Gas Fireplace...
  • Page 19: Pebble Installation

    ANT NOTE: Only the supplied and approved pebbles / glass crystals are to be used with these fi replaces. Use of any other type of pe glass crystals or other material can create a danger and will void the warranty. White River Pebbles shown surrounding the Burner Natural River Pebbles shown surrounding the Burner Regency HZO42 (Aus) Gas Fireplace...
  • Page 20: Volcanic Stone Installation

    Volcanic Stones + Glass Crystals Volcanic Stones Ivory /Tan + Glass Crystals For the PTO30, PTO60 For the HZO42 & HZO42AUS & Plateau Series only only Volcanic Stones Slate /Grey + Glass Crystals For the HZO42 & HZO42AUS only Regency HZO42 (Aus) Gas Fireplace...
  • Page 21: Optional Log Set Installation

    Diagram 3 3) Install log E on the right side of the burner as shown below. Orient log E in the same way and in a similar position as depicted in Diagram 4. Diagram 4 Regency HZO42 (Aus) Gas Fireplace...
  • Page 22 5) Install log F on the right side of the burner as shown below. Orient log F in the same way and in a similar position as depicted in Diagram 6. Diagram 6 Final Install Regency HZO42 (Aus) Gas Fireplace...
  • Page 23: Heat Defl Ector Installation

    INSTALLATION HEAT DEFLECTOR INSTALLATION 1) Install the heat defl ector to the top inside of the fi rebox with 4 screws as shown below. Heat Defl ector Heat Defl ector Installed Regency HZO42 (Aus) Gas Fireplace...
  • Page 24: Faceplate Installation

    There are 3 slots on each tab so the faceplate to accommodate different fi nishing materials. Trim Piece To remove - reverse steps. Final Install Install logo onto faceplate. 43.250 1098.55 Faceplate Dimensions Regency HZO42 (Aus) Gas Fireplace...
  • Page 25: Glass Wind Shield Installation

    Starting from one corner - slide the cover over the corner, then stretch the cover until it is fi tted over all four corners. CAUTION: Never start the unit with the cover on. Let the unit cool before installing the cover. Turn off gas supply to unit before installing cover. Weather Cover Installed Regency HZO42 (Aus) Gas Fireplace...
  • Page 26: Regency Hzo42 (Aus) Gas Fireplace

    Vertical Supports - Tall (B) x 8 Vertical Supports - Short (C) x 6 Base (D) x 1 Header (E) x 1 Corner Brace (F) x 2 Vertical support - back (G) x 1 Wafer Screws Regency HZO42 (Aus) Gas Fireplace...
  • Page 27: Regency Hzo42 (Aus) Gas Fireplace

    (B) pieces. Part B positioned fl at side fl ush with A tab. Important: (B) - (tall vertical supports) must be positioned as shown to ensure the correct installation of (C). Regency HZO42 (Aus) Gas Fireplace...
  • Page 28: Regency Hzo42 (Aus) Gas Fireplace

    fl at side of each inner Part B as shown below. Secure each (C) to bottom (A) with 3 wafer screws (one on each side and one at top as shown below. 44-11/16" (C)Screw (B)+ (C) - fl at sides back to back locations Regency HZO42 (Aus) Gas Fireplace...
  • Page 29: Regency Hzo42 (Aus) Gas Fireplace

    16) Install vertical back support to back of assembly with 2 screws at top and bottom in locations shown below. (F) corner brackets positioned in opposite corners Note: Confi rm assembly is level and square before proceeding with further materials. Regency HZO42 (Aus) Gas Fireplace...
  • Page 30: Regency Hzo42 (Aus) Gas Fireplace

    25mm 1” Max. and could be seriously damaged. 2” Min. 50mm WARNING: Inspect all hoses and if there is evidence of excessive damage, it shall be replaced. Diagram 1 Inspect all hoses prior to use. Regency HZO42 (Aus) Gas Fireplace...
  • Page 31: Operating Instructions

    Unit will repeat step 2. SHUTDOWN PROCEDURE 1) Turn ON/OFF switch. 2) If service is to be performed - you must discon- nect both sources of power to the unit, the main power and battery. Regency HZO42 (Aus) Gas Fireplace...
  • Page 32: Copy Of Lighting Plate Instructions

    After approximately 2 seconds turn on ON/OFF switch. a c c o m p a n y i n g THIS INSTRUCTION PLATE c) L'unité répétera l'étape 2. c) Unit will repeat step 2. appliance. 918-892a Regency HZO42 (Aus) Gas Fireplace...
  • Page 33: Maintenance Instructions

    4) The heater is fi nished in a heat resistant paint and should only be ® NOT BE PLACED ON OR NEAR THE APPLIANCE. refi nished with heat resistant paint. Regency uses StoveBright Paint - Metallic Black #6309. 5) Make a periodic check of burner for proper position and condition. Visually ANY PROTECTIVE DEVICE REMOVED FOR SERVICING, SHALL check the fl...
  • Page 34: Valve Assembly Replacement

    7) Remove the screw and panel clip on the left side. Remove the left side panel once the clip has been removed. 8) Remove the back panel once the 2 side panels have been removed. Regency HZO42 (Aus) Gas Fireplace...
  • Page 35: Battery Replacement

    14) Remove the DFBC from the unit - see page 37. 3) Install 4 - AA batteries and reverse steps. 15) Remove 6 screws an lift out valve tray. 16) Replace with new valve tray and reverse steps. Inspect gasket condition, replace if necessary. Regency HZO42 (Aus) Gas Fireplace...
  • Page 36 3) Disconnect the Black sparker wire with black spade connector from CN3. See Diagram 2 below. Diagram 5 Valve wire Diagram 2 Sparker Wire 4) Disconnect the white and green On/Off switch wires. See Diagram 3 below. White Green Diagram 3 ON/OFF wires Regency HZO42 (Aus) Gas Fireplace...
  • Page 37: Main Assembly

    Orifi ce # 29 (NG) 911-976 Digital Fireplace Burner Control 904-434 Orifi ce # 47 (LPG/ULPG) 918-976 Manual 6) 326-574/P Valve Assembly NG 326-576/P Valve Assembly Propane/ULPG 7) 326-007/P Front access panel 8) 326-008 Burner Tray Cover Regency HZO42 (Aus) Gas Fireplace...
  • Page 38: Burner Assembly

    Valve NG SIT 880 326-930 Log Set 911-025 Valve LPG/ULPG SIT 880 11) 326-008 Burner Tray Cover 12) 911-006 Pilot Assembly - NG 911-007 Pilot Assembly - LPG/ULPG 911-037 Flame Sensor 911-038 Igniter 910-432 Pilot Tube Regency HZO42 (Aus) Gas Fireplace...
  • Page 39: Accessories

    Description Refl ective Stainless Steel Inner Panels 326-021 Rear panel staniless 326-022 Left Panel Stainless 326-023 Right Panel Stainless 14) 940-368/P Glass windshield 15) 326-554 Faceplate Brushed Stainless 946-676 Copper Glass Crystals 946-695 Garden Stones Regency HZO42 (Aus) Gas Fireplace...
  • Page 40: Limited Warranty

    NOTES Regency HZO42 (Aus) Gas Fireplace...
  • Page 41 NOTES Regency HZO42 (Aus) Gas Fireplace...
  • Page 42 NOTES Regency HZO42 (Aus) Gas Fireplace...
  • Page 43: Limited Warranty

    Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited warranty to the original purchaser of a Regency ®...
  • Page 44 Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency is a trademark of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2013, FPI Fireplace Products International Ltd. All rights reserved.

This manual is also suitable for:

Hzo42-ulpgHzo42

Table of Contents