Related Manuals for Telikou MS-500
Summary of Contents for Telikou MS-500
- Page 1 TELIKOU Intercom System MS-500（4+1 channel) Main Station Instruction Manual © TELIKOU Systems All Rights Reserved...
-
Page 2: Table Of Contents
TELIKOU MS-500（4+1Channel）Main Station Contents General Specialty III. Basic operation 1. Front panel 1) Microphone switch (Mic.) 2) Announce switch (ANN.) 3) Call switch (Call) 4) Tone Alert volume control (Tone Alert) 5) Microphone Selection switch (Mic. Select) 6) Panel Microphone plug (Panel) 7) Headset plug (Headset）... -
Page 3: General
Technical Specification General Thank you for choosing TELIKOU intercom product. MS-500 main station can be used for television station, communication center, UB truck, live performance and any other environment need communication. Work with BK-500 belt pack, it can start Tally light function on four channels. -
Page 4: Front Panel
TELIKOU MS-500（4+1Channel）Main Station Front Panel 1) Microphone switch (Mic.) Turn up or down microphone switch handle will send amplified microphone signal through intercom line. When this function is active, the LED above will light. The switch positions are as follow: The selected microphone is activated, the switch is self-locked. - Page 5 TELIKOU MS-500（4+1Channel）Main Station 4) Tone Alert Volume Control When MS-500 receives external call signal, the internal buzzer will sent a hum to panel speaker and earphone. This knob adjusts the hum level. 5) Mic. Select Switch Set the Mic. select switch to select whether the panel microphone or the headset microphone is active.
- Page 6 A call signal been sent to the channel. 15) Program Level Adjust program audio level which goes into MS-500, by clockwise or counterclockwise direction. 16) Feed To LED This LED lights when Program feed to (17) function works.
- Page 7 21) Sidetone zero-adjusting The MS-500 uses full-duplex audio in which the talk and listen audio are sent and received on the same line. Thus, when you talk on a channel, you will also here your own voice back in the speaker or earphone.
-
Page 8: Rear Panel
Switch is turned on. XLR-3F balanced input. The pin out of Program Input connector is as follows: Pin 1 --- Common (Shield) Pin 2 --- + Audio Pin 3 --- - Audio 26) Online It is used to connect TELIKOU working main stations in the system. XLR-3M. The pin out of Online Connector is as follows:... - Page 9 1uF non-polarized capacity on Pin 2 of XLR. 27) Termination Switch The MS-500 has two different termination options. Normally this switch is set as “ON”. In PL intercom system has only one termination point. If there is more than one base station in the system, the termination point should be at main control station.
- Page 10 TELIKOU MS-500（4+1Channel）Main Station Pin 3 --- Audio Pin 4 --- Tally light drive signal output (Green) Pin 5 --- Tally light drive signal output (Red) 30) Tally light external control signal connector (Tally In) The definition of DB9 is as follow:...
- Page 11 TELIKOU MS-500（4+1Channel）Main Station Pin 3 --- Audio Signal Pin 4 --- Tally light drive signal output Pin 5 --- Tally light drive signal output B. A pair of XLR-3 connectors is put on each end of two-core shield cable, one end is XLR-3M and another end is XLR-3F.
- Page 12 TELIKOU MS-500（4+1Channel）Main Station Pin 2--Mic hot Pin 3--earphone common Pin 4--earphone hot Pin 5—Null Panel Mic connector: XLR-3F Pin 1 -- Mic common Pin 2 -- Mic hot Pin 3 – Null Intercom cable connector: XLR-3F Pin 1 --- Common (Shield)
- Page 13 Solution: Turn off microphone when it is not need. Problem: Power LED wink Cause 1: Short circuit Solution 1: Remove all the intercom cables from MS-500. Check all channels one by one, until find the short point. Cause 2: Overload Solution 2: Decrease the numbers of end user stations;...
- Page 14 WARNING: THIS IS A POTENTIALLY DANGEROUS SITUATION. A SHOCK HAZARD MAY EXIST BETWEEN A REMOTE STATION HEADSET AND GROUND. Problem: Can not turn on the Mic function on all the beltpacks Cause 1: The connection among TELIKOU main stations must go via ―Online‖ connector on rear...
- Page 15 Problem: Can not turn off the Mic function on all the beltpacks after pressing RMK button Cause 1: The connection among TELIKOU mains stations must go via ―Online‖ connector. If main stations are connected by Intercom Line connector, RMK function will not work properly.
Need help?
Do you have a question about the MS-500 and is the answer not in the manual?
Questions and answers