Amplifier Power Requirement Chart - Sonance SONAMP DSP 2-150 Instruction Manual

SONAMP DSP 2-150 MULTI-CHANNEL POWER AMPLIFIER INSTRUCTION MANUAL
Powering the Amplifier
2-100
LEVEL
The Sonamp DSP
a removable IEC power
(Figure 6). A 14-gauge EIA standard
VOLTAGE TRIGGER
120-volt grounded
included with the amplifier.
IN OUT
AUTO ON
Each time the amplifier's
cord is initially plugged in and the
3-30 VOLTS
POWER switch is
AC or DC
channel outputs are
for approximately 12 seconds and all
PROTECTION LEDs will illuminate briefly
while the amp boots up.
IMPORTANT: DO NOT PLUG THE POWER CORD INTO THE WALL
OUTLET UNTIL ALL SYSTEM CONNECTIONS HAVE BEEN MADE
AND VERIFIED.
Plug the female end of the power cable into the Power Connector
on the amplifier's rear panel and plug the male end directly into a
grounded 15 amp or 20 amp wall outlet.
IMPORTANT: DO NOT PLUG THE AMPLIFIER'S POWER CORD
INTO A CONVENIENCE OUTLET ON ANY OTHER AUDIO OR
VIDEO COMPONENT.
If the electrical service is subject to frequent sags, spikes, or
brownouts, a power conditioner designed for use with high fidelity
equipment should be employed to protect the amplifier.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE,
REPLACE THE FUSE WITH ONLY THE SAME TYPE AND RATING.
Amplifiers Power Requirements:
Model Input Voltage
DSP 2-150 100-120V AC
Model Input Voltage
DSP 2-150 220-240V AC
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
2-150 features
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
connector
power cable is
T5AL / 250VAC
power
CAUTION
REPLACE FUSE ONLY WITH
SAME TYPE AND RATING
turned ON, ATTENTION all AC 100-120V ~ 60Hz
REMPLACER UNIQUEMENT AVEC LE
AC 220-240V ~ 50Hz
MEME TYPE ET CALIBRE DU FUSIBLE
disconnected
FIGURE 6: IEC POWER
CORD CONNECTION
Output Power (sinewave)
Full Power All Channels @8 ohms
Full Power All Channels @4 ohms
1/8 Power All Channels @8 ohms
1/8 Power All Channels @4 ohms
@ Idle
IP/IR Standby
@ Standby
Output Power (sinewave)
Full Power All Channels @8 ohms
Full Power All Channels @4 ohms
1/8 Power All Channels @8 ohms
1/8 Power All Channels @4 ohms
@ Idle
IP/IR Standby
@ Standby
FIGURE 7: SONAMP DSP 2-150 MULTI-CHANNEL AMPLIFIER POWER REQUIREMENTS
Source Connections/Selection DSP 2-150
There are two options when connecting audio inputs to the
DSP 2-150 amplifier (see Figure 8):
Primary Line Inputs 1-L, 1-R - Use these inputs for primary
audio source.
Secondary Line Inputs 2-L, 2-R - Use these inputs for a secondary
audio source, paging, or a doorbell.
FIGURE 8: SONAMP DSP 2-150 LEFT, RIGHT LINE INPUTS
15 AMP Breaker
Draw Watts Qty of Amplifiers
371 3
392 3
72 20
74 19
31
1.5
0.48
13 AMP Breaker
Draw Watts Qty of Amplifiers
359 4
376 3
69 20
71 20
28
1.1
0.5
6
20 AMP Breaker
Qty of Amplifiers
5
4
26
25
20 AMP Breaker
Qty of Amplifiers
5
5
27
27