Related Manuals for Sonance DSP 8-130 MKII SONAMP
Summary of Contents for Sonance DSP 8-130 MKII SONAMP
- Page 1 DSP 8-130 MKII SONAMP MULTI-CHANNEL POWER AMPLIFIER ® WITH I N S T R U C T I O N M A N UA L 06.14.17...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety Introduction/Box Contents Front Panel/Rear Panel Amplifier Power Requirement Chart Connections and Volume Level Controls Protection Circuitry and LEDs Rack Ear Installation and Shelf Mounting Software V2 Network Connection Instructions Homepage Basic Setup Page Advanced Setup Page General Settings Tab In/Out Settings Tab EQ Settings Tab... -
Page 3: Safety
DSP 8-130 MKII ® SONAMP MULTI-CHANNEL POWER AMPLIFIER WITH I N S T R U C T I O N M A N U A L Important Safety Information • The amplifier has been exposed to rain. • The amplifier does not appear to operate normally or exhibits You should always follow these basic safety precautions when using a marked change in performance. - Page 4 I N S T R U C T I O N S I M P O R TA N T E S C O N C E R N A N T L A S É C U R I T É Lisez soigneusement ces instructions.
-
Page 5: Introduction/Box Contents
Introduction Unpacking Thank you for purchasing the Sonance Sonamp DSP 8-130 MKII Save the carton and polystyrene inserts for future safe transport in amplifier. When properly installed, this amplifier will give you many case the amplifier is moved or requires shipping for repair. -
Page 6: Front Panel/Rear Panel
The DSP 8-130 MKII amplifier has four pair of LINE INPUTS and four pair of Loop OUTPUTS. When the Sonance logo on the power switch is lit bright white, the amplifier has power and is turned ON and ready to operate. -
Page 7: Amplifier Power Requirement Chart
Powering the Amplifier CAUTION 2-100 LEVEL IMPORTANT: DO NOT PLUG THE POWER CORD INTO THE WALL RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS OUTLET UNTIL ALL SYSTEM CONNECTIONS HAVE BEEN MADE The Sonamp DSP 8-130 MKII features RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR AND VERIFIED. -
Page 8: Connections And Volume Level Controls
Source Connections DSP 8-130 MKII Protection Circuitry and LEDs On the left side of the rear panel are the left and right audio inputs The Sonamp amplifiers have a multi-stage protection system to for all eight channels. In addition to the audio inputs there are also prevent damage to your amplifier and speakers. -
Page 9: Network Connection Instructions
Free Type Field Assign Preset Click on the individual channels to show the drop down menu of preset options. Once you locate the preset for your Sonance SONARC Homepage speakers click on the name to set the preset. Each Sonance... -
Page 10: Advanced Setup Page
Front panel level controls overwrite these two settings. DHCP ON/OFF is the first option in IP SETUP . All Sonance DSP series amplifiers ship with DHCP (Dynamic Host Connection NOTE: LEFT AND RIGHT CHANNELS ARE LINKED. OUTPUT Protocol) ON. - Page 11 Auto On IP Address The second setting in the IP SETUP section is the IP address. Select the Auto On method you would like to use with the blue When DHCP is ON the current IP address will be displayed. pull down menu.
-
Page 12: In/Out Settings Tab
DSP Preset for 15 minutes, the channel will go to sleep. From the sleep Apply any of the available Sonance DSP presets to each state the channel will take approximately 2-3 seconds channel of the amplifier independently. You can apply any open to reproduce audio again. -
Page 13: Eq Settings Tab
The green IMPORT EXPORT buttons allow you to save all 50 for each channel. EQ Presets provide best possible audio quality for most Sonance speakers. EQ Presets are available presets in one file. This option can be useful when setting at http://www.sonance.com/electronics/amplifiers/dsp. - Page 14 Import Single Preset 1. Import speaker preset to a location on your computer. All Sonance DSP amplifier models feature a 10 band This can be accomplished by saving a DSP preset parametric EQ. Adjustments made to the EQ will be displayed downloaded from Sonance website.
-
Page 15: Tilt Control
Limiter Tilt Control The limiter operates as a brick wall limit on the output of the The tilt controls are very sophisticated bass and treble amplifier. The limiter drop down menu has -3dB, -6dB and control. By selecting a start frequency and level you can -12dB options. -
Page 16: Specifications
17 1/4” x 2 1/8” x 16 13/16” (438mm x 54mm x 427mm) Dimensions w/ Rack Ears w/o Feet (W x H x D) 19” x 1 3/4” x 16 13/16” (482mm x 44mm x 427mm) Shipping Weight 18 lbs (8.2kg) CAD Files available for download at www.sonance.com/electronics/amplifiers/dsp... -
Page 17: Appendix A
APPENDIX A LED Indicator Explanation Dim White Power Button Amplifier is plugged in and in standby mode. Bright White Power Button Amplifier is active. Power Switch Blinking The amp is in ID Amp Mode (see page 9). Green LED Signal is present (>2.5mv) on channel. Blinking Green Signal is going above and below the active level or between songs. -
Page 18: Appendix B
APPENDIX B DSP 8-130 MKII Amplifier - Auto On / Sleep Mode Details AUTO ON SETTING SLEEP MODE OPTIONS TIME TO MUSIC ETHERNET AUDIO Always On Always On AUDIO 15 MIN 6-8 seconds Always On AUDIO 3 HRS 6-8 seconds Always On AUTO ON SETTING SLEEP MODE OPTIONS... -
Page 19: Warranty
Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated below. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.
Need help?
Do you have a question about the DSP 8-130 MKII SONAMP and is the answer not in the manual?
Questions and answers