Advertisement

Quick Links

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
OWNER'S MANUAL
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
WHAT TO DO IF YOU SMELL GAS
• Open windows/extinguish any open
flame.
• Do not try to light any appliance.
• Do not touch any electrical switch
or use any phone in your building.
• Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
• If you cannot reach your gas
supplier, call the fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapours and liquids in the
vicinity of this or any other appliance.
WARNING:
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life. Installation and
service must be performed by a qualified installer, service agency or the gas supplier.
Massachusetts installations (Warning): This product must be installed by a licensed
plumber or gas fitter when installed within the Commonwealth of Massachusetts.
Other Massachusetts code requirements: Flexible connector must not be longer than
36in., a shut off valve must be installed; only direct vent sealed combustion products
are approved for bedrooms/bathrooms. A carbon monoxide detector is required in all
rooms containing gas fired direct vent appliances.
Sonnet
B Y : S H E R W O O D I N D U S T R I E S L T D
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
50-1472

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sonner and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Enviro Sonner

  • Page 1 SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE Sonnet B Y : S H E R W O O D I N D U S T R I E S L T D OWNER’S MANUAL INSTALLER: Leave this manual with the appliance.
  • Page 2: Safety Precautions

    Safety Precautions FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION: • To prevent injury, if the pilot or pilot and • All ENVIRO gas-fired appliances must be installed in accordance with their instructions. Carefully read all burners have gone out on their own, open the the instructions in this manual first.
  • Page 3: Table Of Contents

    Table of Contents Safety Precautions......................2 Table of Contents......................3 Codes And Approvals....................4 Specifications.......................5 Rating Label Location..................5 Dimensions.......................5 Operating Instructions....................7 Lighting and Turning Off Instructions..............7 Remote Handset Controls...................8 Control Panel....................9 Blower Speed....................10 Normal Sounds During Operation..............10 Adjusting Venturi Air Settings................10 Maintenance And Service....................11 Cleaning The Glass..................11 Cleaning The Firebox..................11 Replacing The Glass..................11...
  • Page 4: Codes And Approvals

    After the unit has gone through the first burn, turn the unit off, let the unit get cold then remove the glass door and clean it with a good gas fireplace glass cleaner, available at your local ENVIRO dealer. See “D ”...
  • Page 5: Specifications

    Specifications ATING ABEL OCATION The rating label is located under the control panel and is attached to a rectangular metal sheet that is chained to the fireplace. IMENSIONS " (355mm) " " Sonnet Top without (336mm) (278mm) a Trim Installed "...
  • Page 6 Specifications ” (809mm) to 403⁄4” (1035mm) 311⁄4” (794mm) ” (555mm) to 26 ” (669mm) ” (528mm) ” (569mm) 23” (583mm) Figure 2: Sonnet Adjustable Surround, Classic, and Base Shelf with Riser. Table 1: Sonnet Options Dimensions. Colonial - 3 Sided Colonial - 4 Sided Classic - 3 Sided Classic - 4 Sided...
  • Page 7: Operating Instructions

    Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. IGHTING AND URNING NSTRUCTIONS Hot while operating.
  • Page 8: Remote Handset Controls

    Operating Instructions The Sonnet is designed to gradually lower or raise the flame as is needed in application. It normally does not just turn on and off. This is very dependant on the size of the room the unit is located in. During the first several operational cycles the electronics go through a learning process that establishes how the system will react to the environment it is in.
  • Page 9: Control Panel

    Operating Instructions TIMER MODE – (appliance must be in standby mode; pilot ignited): The Timer setting allows you to set two (2) burner times and two (2) burner times every 24 hours. to operate as a thermostat, TEMP must be set at 40°F (4.5°C) or higher. If the setting is decreased to --, the motor will turn the valve to the standby position in the moon times and await the next burner...
  • Page 10: Blower Speed

    Operating Instructions LOWER PEED The blower will come on only when the fireplace is up to temperature (approximately 20 minutes). Pressing the fan’s three (3) position rocker switch on the unit’s control panel will change the speed of the fan; it is Low/Off/High (refer to Figure 4). The fan can not be controlled with the handset. ORMAL OUNDS URING...
  • Page 11: Maintenance And Service

    Do not operate with the glass front removed, cracked or broken. Removal and replacement of the glass from the door must be done by a licensed or qualified service person. The glass must be purchased from an ENVIRO dealer. No substitute materials are allowed.
  • Page 12: Glass Door Removal

    Maintenance And Service LASS EMOVAL Remove the glass door by placing the hooked end of the door release tool in the hole on the door latch mechanism (see Figure 9) and pulling the latch out then up over the lip on the door. When the two (2) latches have been released, tilt the door forward and then lift up to unhook the bottom door tabs...
  • Page 13: Changing Remote Handset Code

    Maintenance And Service HANGING EMOTE ANDSET A code is preset for the remote handset and receiver, but can be changed if required. If one or more Sonnets are to be installed, confirm that the remote control signal codes are different for each unit.To change the code, complete the following: 1.
  • Page 14: Fuel Conversion

    Maintenance And Service ONVERSION TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY Please read and understand these instructions before installing. Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
  • Page 15 Maintenance And Service b) Push the slider, with your finger or flat head screwdriver, to the left if it is to be set for natural gas or to the right for propane (see to Figure 24). c) Turn the pilot head a 1⁄4 turn clockwise;...
  • Page 16: Initial Installation

    Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. LEARANCES TO OMBUSTIBLES Maintain sufficient clearances for operation, service and maintenance. • A clearance of 71⁄2” (191 mm) minimum is required from the side of the unit to the sidewalls. •...
  • Page 17: B-Vent Model

    Initial Installation ODEL WARNING: This appliance has been designed to operate by drawing combustion air and dilution air from the room. It is also designed to draw room air for proper heat circulation from the sides of the unit. Blocking or modifying these openings in any way can create hazardous situations, either through poor venting or by overheating.
  • Page 18: Converting A Direct Vent Fireplace To A B-Vent Fireplace

    Initial Installation QUALIFIED INSTALLERS ONLY 3. Remove log and ember set and all wrapping material from the stove. Remove wrapping material from log and embers and check for any damage. If damage is observed, do not use unit and contact your local dealer.
  • Page 19 Initial Installation QUALIFIED INSTALLERS ONLY b) Cut the tie strap from around the wires for the spill switch. c) Feed the connector end of both wires through the hole in the bottom left corner of the back panel (see Figure 31). d) Using needle nose pliers remove the jumper wire on the thermocouple (see Figure 32).
  • Page 20: Venting Fireplace Inserts

    IREPLACE NSERTS The ENVIRO Sonnet may be installed and vented into any solid fuel fireplace that has been installed in accordance with the National, Provincial/State and local building codes and has been constructed of non-combustible materials. Before starting, refer to I...
  • Page 21: Direct Vent Vertical Vent Termination

    Initial Installation QUALIFIED INSTALLERS ONLY Install sealed throat connector or flashing to prevent leakage of room air up through chimney. DV Only: Before installing vent liners, mark each liner on both ends to designate which is the intake and the exhaust. Measure the height of the chimney beforehand and purchase the appropriate kit.
  • Page 22 Initial Installation QUALIFIED INSTALLERS ONLY 3. Install the flex pipe assembly up through the chimney, ensure that the pipe slides through far enough to connect onto the Vertical Vent Cap. Note: For any chimney over 15’ (4.6m), install the Sonnet 15’ 2” & 3” Flex Vent (part #50-1512) and the Sonnet 2”...
  • Page 23: Remote Handset Wall Bracket Installation

    Initial Installation QUALIFIED INSTALLERS ONLY The height for the vent must be between 10ft (3.05m) and 35ft (10.67m). Install sealed Vertical Vent Cap to prevent leakage of room air up through chimney. The intake is 2" (51mm) and the exhaust is 3" (76mm). Measure the height of the chimney beforehand and purchase the appropriate kit.
  • Page 24: Electrical Requirements

    Initial Installation QUALIFIED INSTALLERS ONLY LECTRICAL EQUIREMENTS The fan will not operate if the appliance is cold. A few minutes after the appliance is lit and the fan is set to low or high, the fan will automatically turn on. The fan will automatically turn off after the appliance has cooled down.
  • Page 25 Initial Installation QUALIFIED INSTALLERS ONLY Kit Contents: Quantity Description Quantity Description Fan Assembly Power Cord - 6ft (1.8m) Wiring Harness Star Washer Temperature Sensor #8-32 X 3⁄4” T-20 Screw Fan Control; 3 Position Switch Please ensure that all components are supplied with this kit. If components are missing or have been damaged, contact your dealer, distributor or courier company before starting this installation.
  • Page 26: Gas Line Connection

    Initial Installation QUALIFIED INSTALLERS ONLY 8. Pull the control panel straight out (see Figure 52). There are two (2) tabs on the bottom of the control panel that fit in two (2) slots in the Sonnet cabinet bottom. 9. Slide the temperature sensor into the holding tabs below the left end of the burner behind the control panel.
  • Page 27 Initial Installation QUALIFIED INSTALLERS ONLY Main Valve Knob Pressure Tap In Pressure Tap Out Line Out Pilot Line Gas Line In Thermocouple Line Figure 55: Opening Inlet Pressure Tap on Figure 54: Labeled Gas Valve. Valve. TO TEST VALVE PRESSURES: The pressure taps are located on the front side of the valve (see Figure 54 &...
  • Page 28: Secondary Installation

    Secondary Installation & R PTIONAL HELF ISER The Sonnet Base Shelf (15⁄8” (41 mm) high) and Base Shelf Riser (21⁄8” (54 mm) high) are black powder coated components that can be combined to create a riser with an overall height of 2 ”...
  • Page 29 Secondary Installation Note: The Adjustable Surround can only be installed onto the Colonial or Classic Surrounds, it is not intended to be installed on its own with the Sonnet unit. ASSEMBLY: 1. Line up the two (2) screw holes in the left hook bracket with the second slot in on the back of the left trim side (refer to Figure 58).
  • Page 30 Secondary Installation Required Width Adjustable Adjustable Surround Corner Surround Corner Required Height Trim (Classic or Colonial) Note: Mounting brackets removed for clarity Figure 61: Marking offsets on Trim, Relates to Table 7. b) Subtract the minimum size of Table 7: Adjustable Surround Example, Relates to Figure 61. the surround (23 ”...
  • Page 31 Secondary Installation 11. Center the keystone over the gap at the top of the trim and slide it into place. Slide the side covers over the bottoms of the sides so the cover will be as low as the trim (see Figure 63).
  • Page 32: Optional Cast Andiron & Grate

    Secondary Installation & G PTIONAL NDIRON RATE A footing (i.e. Base Shelf) may need to be installed before the Cast Andiron is installed so that the Cast Andiron has something to sit on. Hook the Andiron assembly over the two (2) bushings near the bottom of the Sonnet, pointed out in Figure 66, and snap them firmly down into place.
  • Page 33: Log Set And Ember Installation

    Secondary Installation ET AND MBER NSTALLATION NOTE: The logs are fragile and should be handled gently. The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched” and will not burn correctly. The burner and a few of the logs come with locator pins and ledges, which make alignment easier.
  • Page 34 Secondary Installation Figure 73: The center of the right log fits onto the locator pin on the back right log (see Figure 72). The front of the log is to rest on the burner and the back end of the log rests on the back brick panel.
  • Page 35 Secondary Installation Figure 76. Log Set and Ember Installation. Figure 77. Sonnet complete log set-up with embers burning. NOTE: While the glass is still removed, it is recommended that the gas line be purged by lighting the pilot. When lighting the fireplace for the first time since the log set and embers have been installed/replaced, watch for ignition at ALL the burner ports.
  • Page 36: Trouble Shooting

    Trouble Shooting Problem Possible Cause Solution No transmissions; Receiver must learn new • Reset the receiver’s code, refer to M AINTENANCE remote control code. ERVICE HANGING EMOTE ANDSET doesn’t work. One or more of the • Replace the batteries, refer to M AINTENANCE batteries are dead.
  • Page 37 Trouble Shooting Possible Cause Solution Spark will not light Air in the pilot supply line. • Purge the line or start ignition several times. the pilot after No spark at pilot burner • Check spark gap. repeatedly pressing • Check wiring connections to ignitor. the spark ignitor.
  • Page 38: Parts List - Components

    Trouble Shooting Problem Possible Cause Solution 3 short beeps while One or more of the • Replace the batteries, refer to M AINTENANCE motor turns. batteries are low. ERVICE EPLACING ATTERIES : Creating an electrical short between ARNING the batteries/battery box and metal parts of the appliance may render the receiver inoperable.
  • Page 39 Parts List - Components Reference Part Description Part Number Number Large Ember Nuggets Only 50-832 Ceramic Wool Embers Only 50-893 Sonnet Log set 50-1420 Sonnet Conversion Kit LP to NG Maxitrol 50-1445 Sonnet Conversion Kit NG to LP Maxitrol 50-1446 Maxitrol Remote Control 50-1458 Sonnet Owners Manual...
  • Page 40: Parts Diagram - Components

    Parts Diagram - Components...
  • Page 41: Parts List - Options

    Parts List - Options Reference Option Description Part Number Number Sonnet Surround Adjustable 50-1414 Sonnet Surround Trimmable 50-1415 Sonnet Cast Andiron & Grate 50-1417 Sonnet Fan Kit 50-1418 Sonnet Firebox Brick Liner Double Sided 50-1419 Sonnet Colonial Surround Panel 50-1456 Sonnet Classic Surround Panel 50-1457 Sonnet Colonial Surround 4 Sided...
  • Page 42: Warranty

    Sherwood Industries Ltd. The use of such products may nullify the Limited Warranty on this stove. If unsure as to the extent of this Limited Warranty, contact your authorized Enviro dealer before installation.
  • Page 43 21. The Limited Warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Enviro fireplace or stove without the express written permission of Sherwood Industries Ltd. and bearing a Sherwood Industries Ltd.
  • Page 44: Installation Data Sheet

    Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: NAME OF DEALER: _________________________________________ _________________________________________ ADDRESS: ADDRESS: _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ PHONE:___________________________________ MODEL:___________________________________ NAME OF INSTALLER: SERIAL NUMBER:___________________________ _________________________________________ DATE OF PURCHASE: _____________...

This manual is also suitable for:

Sonnet

Table of Contents