Sony XDS-PD1000 Operation Manual page 43

P3 AUDIO page
Item Setting
F1: A5 VOL Sets the volume of audio channel 5.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F2: A6 VOL Sets the volume of audio channel 6.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F3: A7 VOL Sets the volume of audio channel 7.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F4: A8 VOL Sets the volume of audio channel 8.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F5: – (Unassigned function button)
F6: – (Unassigned function button)
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
• Set the VARIABLE switch of the front panel to "REC" or "PB".
• Set setup menu item 131 AUDIO VOLUME to "each".
P4 TC page
Item Setting
F1: TCG Selects the timecode signal to which the
internal timecode generator synchronizes.
INT: Follow the initial value set from the
front panel or remotely from the
device connected to a REMOTE (9P)
connector.
EXT: Synchronize to external timecode
signal input to the TIME CODE IN
connector.
SYS: Synchronize to standard reference
timecode signal of a broadcasting
station input to the SYSTEM TC
INPUT connector.
SDI: Synchronize to timecode embedded
into HD-SDI or SD-SDI signal input to
the HD/SD-SDI INPUT connector.
Note
If you select "EXT" or "SDI" when a DVB-
ASI TS signal is input, the internal
timecode generator synchronizes to
timecode data contained in the TS signal.
Item
F2: PRST/RGN Selects the following for the internal
a)
a)
F3: RUN
MODE
a)
F4: DF/NDF
a)
F5: PDPSET
F6: TCR
P5 OTHER page
Item
F1: INDEX
Setting
timecode generator.
PRESET: Presets an initial value for the
timecode generated by the internal
timecode generator, as specified from
the front panel or remotely from the
device connected to a REMOTE (9P)
connector.
TC: Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC: Generate timecode synchronized to
VITC read by the internal timecode
reader.
Selects the timecode run mode.
FREE RUN: Timecode advances as long
as the unit is powered on, regardless
of the unit's operating state.
REC RUN: Timecode advances only
during recording. When you select this
item, also set F1: TCG on this page to
"INT" and set F2: PRST/RGN to
"PRESET".
Selects the frame count mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF: Drop-frame mode
NDF: Non-drop-frame mode
When the system frequency is set to 1080/
59.94i, 1080/29.97P, or 720/59.94P,
presets the timecode of the A frame of the
pulldown sequence.
24F TC: Reference timecode for A frame
30F TC: Timecode after pulldown
conversion from 24-frame timecode
Selects the type of timecode to display in
the time data display area.
TC: Display TC.
VITC: Display VITC.
Setting
Sets the index picture (thumbnail) of a clip
being played back. (see page 65)
Basic Operations of the Function Menu
43