Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Matrix Versa Single-Station Strength
Summary of Contents for Matrix Versa Single-Station Strength
- Page 1 OWNERS MANUAL Versa Single-Station Strength VS-S23 Converging Shoulder Press...
-
Page 2: Table Of Contents
Table Of Contents Safety, General Care & Maintenence ..........3 Getting Started (Product Specifications) ..........5 Assembly Information ................6 Markings ....................7 Parts List ....................8 Installation & Assembly: Value Line Part 1 Weight Stack to User Frame Assembly ......10 Part 2 Arm Assembly ..............12 Part 3 Cable Assembly .............. -
Page 3: Safety, General Care & Maintenence
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or supervis- ing personnel on proper usage of the equipment. It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use. - Page 4 IMPORTANT SAFETY INSTRUCTIONS WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID INJURY! Never allow children on strength training equipment. Teenagers must be supervised at all times while using this equipment.
-
Page 5: Getting Started (Product Specifications)
GETTING STARTED EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST EXERCISE PLACARD PRODUCT SPECIFICATIONS TECH SPECS Overall dimensions 61”L X 57”W X 66”H Light Stack = 538 lbs (245 kg), Heavy Stack = 608 lbs (276 Weight Shipping weight 402 lbs (182 kg) WARRANTY (Valid in USA only) Frame (not coatings) 10 years... -
Page 6: Assembly Information
UNPACKING Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Ma- trix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the machine. -
Page 7: Markings
MARKINGS WARNING LABEL LOCATIONS... -
Page 8: Parts List
Parts List DESCRIPTION Weight Stack M10 Flat Washer M10 X 20L Socket Head Cap Screw Lower Connecting Tube M10 Nylock Nut User Frame Wide Cupped Flange M10 X 125L Socket Head Cap Screw Upper Connecting Tube Right Arm Assembly Left Arm Assembly M12 Large Flat Washer (Ø40 mm) Belleville Washer M10 X 30L Socket Head Cap Screw... - Page 9 Parts List DESCRIPTION Back Pad M10 X 75L Socket Head Cap Screw Bottom Pad M10 X 20L Hex Bolt Front Shroud Rear Shroud M8 X 25L SHC M8 Flat Washer (Ø20 mm) Top Cap Top Cap Cover PREMIUM KIT COMPONENTS Wing Rep Counter Towel Hook...
-
Page 10: Installation & Assembly: Value Line Part 1 Weight Stack To User Frame Assembly
ASSEMBLY PART 1: USER FRAME ASSEMBLY STEP 1 | USER FRAME INSTRUCTIONS & NOTES DESCRIPTION QUANTITY Weight Stack M10 Flat Washer M10 X 20L SHC Lower Connecting Tube M10 Nylock Nut User Frame Wide Cupped Flange M10 X 125L SHC Install the user frame hardware as shown, but DO NOT FULLY TIGHTEN . - Page 11 ASSEMBLY PART 1: USER FRAME ASSEMBLY STEP 2 | USER FRAME ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M10 Flat Washer M10 X 20L SHC M10 Nylock Nut Wide Cupped Flange M10 X 125L SHC Upper Connecting Tube Install the user frame hardware as shown. Torque all M10 hardware from pages 10 &...
-
Page 12: Part 2 Arm Assembly
ASSEMBLY PART 2: ARM ASSEMBLY STEP 1 | RIGHT & LEFT ARM ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY Right Arm Assembly Left Arm Assembly 40mm Diameter Flat Washer Belleville (Spring) Washer M10 X 30L SHC 20 mm Diameter Shaft Counter Weight M8 Flat Washer M8 X 20L SHC Attach the arms to the frame using the hardware shown, but DO NOT FULLY TIGHTEN... - Page 13 ASSEMBLY PART 2: ARM ASSEMBLY STEP 2 | RIGHT & LEFT ARM ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M12 Flat Washer M12 X 25L SHC 19 20 19 20 Install the pivot cap screw as shown. Torque all arm hardware to: • M10 from step 1 to 77 N-m/57 ft-lbs.
-
Page 14: Part 3 Cable Assembly
ASSEMBLY PART 3: CABLE ASSEMBLY STEP 1 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M10 Flat Washer M10 Nylock Nut Pulley M10 X 50L SHC Floating Pulley Plate View A Cable tension is adjusted by raising or lowering pulley as shown in View A. Note: Nuts for adjustable pulley must be on inside towards weight plates. - Page 15 ASSEMBLY PART 3: CABLE ASSEMBLY STEP 2 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M8 Flat Washer M8 X 45L SHC M8 Nylock Nut Cable Tie Rod End Fully thread cable bolt into tie-rod, then attach to frame. Torque M8 hardware to: 39 N-m/29 ft-lbs.
- Page 16 ASSEMBLY PART 3: CABLE ASSEMBLY STEP 3 | USER FRAME CABLE ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M10 Flat Washer M10 Nylock Nut Pulley M10 X 50L SHC User Frame Cable Install the secondary cable pulleys as shown. Torque hardware to: 77 N-m/57 ft-lbs.
- Page 17 ASSEMBLY PART 3: CABLE ASSEMBLY STEP 4 | USER FRAME CABLE ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M8 Flat Washer M8 Nylock Nut Cable Tie Rod End M8 X 50L SHC *Note: Image shows left arm assembly only, though quantities reflect both left and right arm assemblies. Fully thread cable bolt into tie-rod, then attach to frame.
-
Page 18: Part 4 Seat Pad Assembly
ASSEMBLY PART 4: SEAT PAD ASSEMBLY STEP 1 | BACK PAD AND HEAD PAD ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M10 Flat Washer Head Pad Back Pad M10 X 75L SHC Install the head & back pads as shown. Tighten to 57 N-m/41 ft-lbs. - Page 19 ASSEMBLY PART 4: SEAT PAD ASSEMBLY STEP 2 | BOTTOM PAD ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY Bottom Pad M10 X 20L Hex Bolt Install the seat pads as shown. Torque to 57 N-m/41 ft-lbs.
-
Page 20: Part 5 Plastics Assembly
ASSEMBLY PART 5: PLASTICS ASSEMBLY STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY Front Shroud Rear Shroud (Not shown) Position hangers in their lowest position Install the weight stack shrouds as shown. - Page 21 ASSEMBLY PART 5: PLASTICS ASSEMBLY STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M8 X 25L SHC M8 Flat Washer (20 mm diameter) Top Cap Install the top cap onto the weight stack as shown. Torque to 17 N-m/147 in-lbs.
- Page 22 ASSEMBLY PART 5: PLASTICS ASSEMBLY STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES DESCRIPTION QUANTITY Top Cap Cover Install the top cap covers.
-
Page 23: Part 6 Premium Kit Assembly
ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY Wing Rep Counter Towel Hook ASG Push Grip Premium Pullpin Seat Assist Gas Shock M10 Nylock Nut I M PO RTA NT NOTI CE PLEASE NOTE: Be sure to remove the insulating sheet when installing the Rep Counter. - Page 24 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Rep Counter - Magnet 1. Remove the (2) top cap covers using a flat blade screw driver. 2. Remove the (4) M8 bolts and 20 mm diameter washers that hold the top cap to the weight stack frame.
- Page 25 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 2 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Rep Counter - Sensors 1. Assemble Rep Counter sensor base using (4) screws included with the kit. 2. Assemble (3) sensors located per machine chart shown below. Thread zip ties through holes to secure cables Route wires in groove...
- Page 26 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Rep Counter 1. Remove and discard hole caps using caution not to scratch the paint. 2. Attach plug to Rep Counter. 3. Assemble Towel Hook (3P) and Rep Counter (2P) using the M8 X 35L SHC bolts provided.
- Page 27 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 4 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Wing Assemble the wing (1P) as shown using the M8 hardware provided with the kit. Tighten to 39N-m (29 ft-lbs.).
- Page 28 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES ASG Grips 18 Degrees Remove the end caps using a 3 mm Allen wrench. 2. Cut off and discard the grips. 3. Remove inner collars with a 3 mm allen wrench. 4.
- Page 29 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 6 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Pull Pin Remove the pull pin using an adjustable wrench, and replace with the Premium pull pin (5P).
- Page 30 ASSEMBLY PART 6: PREMIUM KIT ASSEMBLY STEP 7 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Gas Shock Raise the seat to the highest position before adding gas shock (6P) Disassembly and assembly for both Shock must be positioned as shown with gas cylinder ends of shock (Only one end is shown) above piston rod...
-
Page 31: Part 7 Short User Kit
ASSEMBLY PART 7: SHORT USER KIT ASSEMBLY SHORT USER KIT ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANTITY M10 X 18L SHC M10 Flat Washer Coupler Plate M10 X 18L Hex Bolt Foot Rest... - Page 32 ASSEMBLY PART 7: SHORT USER KIT ASSEMBLY STEP 1 | SHORT USER KIT ASSEMBLY INSTRUCTIONS & NOTES Remove end cap by pressing in tabs. 2. Remove and discard hole caps using caution not to scratch the paint. 3. Assemble Coupler Plates. 4.
- Page 36 Matrix Fitness 1600 Landmark Drive Cottage Grove WI 53527 matrixfitness.com Toll-free 866.693.4863 Facsimilie 608.839.8687 Versa Converging Shoulder Press Owners Guide Rev.1.2 Copyright © 2013 Matrix Fitness...
Need help?
Do you have a question about the Versa Single-Station Strength and is the answer not in the manual?
Questions and answers
Is there a starting resistance to this machine?
The starting resistance for the Matrix Versa Single-Station Strength machine is determined by the weight stack. It offers two options: a Light Stack with a starting weight of 538 lbs (245 kg) and a Heavy Stack with a starting weight of 608 lbs (276 kg).
This answer is automatically generated