Basic Settings - GRAUPNER mx-24s Programming Manual

Basic settings

Basic transmitter settings
GENERAL BASIC SETTINGS
Owners name <
Pre-set stick mode
Pre-set modulation
Pre-set min. pitch
Display light
Power-on beep
Battery warning
Own phase name 1 <
Own phase name 2 <
Own phase name 3 <
Own phase name 4 <
5 <
Own phase name
Own phase name 6 <
Own phase name 7 <
8 <
Own phase name
Own phase name 9 <
Own phase name 10 <
L
M
In this menu you can adjust and enter the basic gene-
ral settings which refer to the transmitter overall, e. g.
the owner's name, but also pre-sets for newly set-up
model memories.
Select the relevant line with the rotary control pressed
in, then press the rotary control briefl y.
The presets ...
• "Stick mode",
• "Modulation",
• "Collective pitch min."
... which you set in this menu are automatically ad-
opted in any "free" model memory when you initiali-
se it, i. e. use it for the fi rst time. However, these set-
tings can be changed subsequently using the follo-
wing menus: »Base setup model« and »Helicopter
type«. Changes to the "presets" in this menu there-
fore only affect model memories which you initialise in
the future.
154 154 Program description: Global functions
Note:
The settings you enter in this menu are only entered
>
once, and apply to the whole of the transmitter. When
1
a model memory is initialised, the current settings in
SPCM20
this menu are adopted in that memory.
forwrd
unlim.
Owner's name
yes
At this point you can enter a name with a maximum
9.3V
of 15 characters. Hold the rotary control pressed in to
>
switch to the next screen page ( ) ...
>
>
! " # $ % & ´ ( ) * + , - . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ?
>
@ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
>
` a b c d e f g h i j k l m n
>
ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÿÖÜ
>
Owners name
>
>
>
... where you can enter the owner's name by selec-
ting letters from the character list. Use the rotary con-
trol to select the character or symbol, and press the
rotary control briefl y (or press and turn it) to accept
the chosen character and move on to the next positi-
on. You can move to each character within the name
by holding the rotary control pressed in; (the screen
shows a double arrow "<-->" at the appropriate posi-
tion). Pressing
that point.
Preset stick mode
Basically there are four possible ways of arranging
the principal control functions on the two dual-axis
sticks: the primary functions are aileron, elevator, rud-
der and throttle (or airbrakes) for a fi xed-wing model,
and roll, pitch-axis, tail rotor and throttle / collective
pitch on a model helicopter. Which of these possible
options you select depends on your individual prefe-
rences and fl ying style.
At the bottom edge of the screen you will see SEL.
Press the rotary control briefl y, then select one of the
options 1 to 4. Pressing
c
n o p q r s t u v w x y z { } ~
N
<H-J Sandbru n
n
–
CLEAR inserts a space character at
CLEAR resets the function to
stick mode "1".
Note:
In the fi xed-wing program the direction of effect of the
C1 stick can be changed individually in the »Model
type« menu.
Fixed-wing stick modes
»MODE 1« »MODE 2«
(Throttle right) (Throttle left)
Down-elevator Full-throttle
Up-elevator Motor idle
>
»MODE 3« »MODE 4«
(Throttle right) (Throttle left)
Down-elevator Full-throttle
Up-elevator Motor idle
Helicopter stick modes
»MODE 1« »MODE 2«
(Pitch right) (Pitch left)
Pitch-axis min. Pitch
Pitch-axis max. Pitch
Full-throttle Down-elevator
Motor idle Up-elevator
Full-throttle Down-elevator
Motor idle Up-elevator
min. Pitch Pitch-axis
max. Pitch Pitch-axis