1. Manuals
  2. Brands
  3. ROBBE Manuals
  4. Toy
  5. Arcus V-Tail EDF ARF
  6. Building and operating instructions

ROBBE Arcus V-Tail EDF ARF Building And Operating Instructions

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Building and Operating Instructions
Arcus V-Tail EDF
ARF
No. 2592

Advertisement

Table of Contents
loading

Related Manuals for ROBBE Arcus V-Tail EDF ARF

Summary of Contents for ROBBE Arcus V-Tail EDF ARF

  • Page 1 Building and Operating Instructions Arcus V-Tail EDF No. 2592...

  • Page 2: Table Of Contents

    Specification: Congratulations on your choice of a factory-assembled mo- Wing loading approx.: 33.3 g/dm2 Specification del aircraft from the robbe Length approx.: 770 mm Essential accessories Modellsport range. Many thanks for placing your trust in us. Total surface area approx.:...

  • Page 3: Radio Control System

    Building and Operating Instructions Arcus V-Tail EDF No. 2592 Note re. radio control system For this model you require a radio control system with at least 4 channels. We particularly recommend 2.4 GHz systems. The receiving system is powered by the speed controller’s integral BEC system.

  • Page 4: Installing The Tail Panels

    Building and Operating Instructions Arcus V-Tail EDF No. 2592 Fig. 1 Fig. 2 Fig. 3 - The illustration shows both V-tail halves with the hard pla- - Using Ropoxi 5-minute epoxy, glue both V-tail halves to the - Place the V-tail unit into the opening in the fuselage. The stic joiner prior to assembly.

  • Page 5: Installing The Wings

    Building and Operating Instructions Arcus V-Tail EDF No. 2592 Fig. 7 Fig. 8 Fig. 9 - The illustration shows the assembled V-tail with linkages. - Cut the aileron servo cover so that they fit into the cut-outs - Once the covers have been fitted, fix these to the wings in the foam servo mounts.

  • Page 6: Installing The Rc System Components

    Insulate each soldered joint with a heat-shrink sleeve. pin configuration. (the orange signal wire corresponds to the white wire used for robbe-Futaba systems). - Place the receiver in the fuselage and route the receiver aerial(s).

  • Page 7: Test-Flying, Flying Notes

    Building and Operating Instructions Arcus V-Tail EDF No. 2592 Checking the functions and setting up the control sur- Test-flying, flying notes faces - Read the sections in the Safety Notes entitled “Routine - Charge the flight battery. pre-flight checks” and “Flying the model” before attempting - Switch the transmitter on, and move the throttle stick to the to fly the model for the first time.

  • Page 8: Specification, 20 A Speed Controller

    Building and Operating Instructions Arcus V-Tail EDF No. 2592 Specification - 20 A speed controller: Programming the speed controller: Continuous current: 20 A (Note: please check that the throttle curve is set to 0%, the throttle stick is at the neutral position, and the Peak current: 25 A, (max.

  • Page 9: Replacement Parts List

    • You must have operated the product in accordance with the operating instructions. • You must have used recommended power sources and genuine robbe accessories exclusively. • There must be no damage present caused by moisture, unauthorised intervention, polarity reversal, overloading and mechanical stress. • Please include a concise, accurate description of the fault...

  • Page 10: Service Centre Addresses

    Modellsport GmbH & Co. KG hereby declares that this device conforms to the fundamental requirements and other relevant regulations of the corresponding EC Directive. You can read the original Conformity Declaration on the Internet at www.robbe.com: click on the "Conformity Declaration" logo button which you will find next to the corresponding device description.

Table of Contents