Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ROBBE JetForce
Summary of Contents for ROBBE JetForce
- Page 1 ARTR-Version Nr.: 1205 Instructions and User Manual www.robbe.com V1_03/2019...
-
Page 2: General Information
Robbe Service or have it replaced. Hidden faults can occur due to In particular, all applicable legal requirements must be observed, which can be found in the roof associations or wetness or a crash, which lead to a functional failure after a short operating time. -
Page 3: Warranty
Modellbau Lindinger GmbH hereby declares that this device complies with the essen- tial requirements and other relevant regulations of the corresponding CE directives. The original declaration of conformity can be found on the Internet at www.robbe. com, in the detailed product view of the respective device description or on request. -
Page 4: The Main Function
Congratulations on your purchase of the new JetForce! Product introduction The Robbe JetForce is a river jet boat with which the originals in America race breathtakingly on rivers. The en- SI-2EE is a versatile 2-in-1 2.4GHz electronic control kit for vehicle gines used are large-volume, turbocharged V8 engines or turbine drives. -
Page 5: Low Voltage Protection
Instructions and User Manual R E C E I V E R Parameter setting • type of battery: Lithium battery (LiPo) • Operating mode: two-way without brake (F/R) • Notes: F=Forward, R=Reverse Receiver LED indicator status determination After the remote control is powered on, the LED light is always on, indicating that the transmitter and receiver are connected properly and can work normally. - Page 6 Instructions and User Manual Summary: The SI-2EE brushless electronic control kit is a high-performance, multi-function vehicle-ship A N T E N N A T U B E I N S TA L L AT I O N model electronic control system. Due to its built-in receiver and electronic governor functions, it is a highly integrated and complex function.
- Page 7 Instructions and User Manual G E T T I N G S TA R T E D W H E N YO U A R E F I N I S H E D Remove the canopy from the hull. Power off the receiver by pressing the power Install the receiver antenna in the antenna tube.
- Page 8 Instructions and User Manual Center out the steering nozzle and tighten the set screw using a 1.5mm hex driver. Unlike rudder steerable boats, jet boats must have power applied to the motors in order for the boat to turn. With the trim servo powered and centered, install the servo arm perpendicular to the servo. When making turns, decrease the throttle to reduce the probability of flipping the boat over.
-
Page 9: Wat E R C O O L I N G S Y S T E M
Instructions and User Manual NOTICE: Use Marine Grease to apply 3–5 pumps of grease directly into the brass stuffing tube. Before installing the drive shaft into the brass tube, place a paper towel between the motor coupler and the brass stuffing tube to Applying too much force prevents the drive shaft catch excess grease. -
Page 10: Low Voltage Cutoff (Lvc)
Instructions and User Manual G E N E R A L I N F O R M AT I O N B I N D I N G LO W V O LTA G E C U T O F F ( LV C ) IMPORTANT: Binding is the process of programming the The ESC must be in LiPo mode to safely operate the boat under LiPo power. -
Page 11: Troubleshooting Guide
Servo failed Contact Robbe Product Support Dry out the boat and ensure the hatch is fully The boat hull is not completely Boat tends to dive in closed on the hull before returning the boat... - Page 12 4565 Inzersdorf im Kremstal Austria Phone: +43(0)7582/81313-0 Mail: info@robbe.com UID No.: ATU69266037 „robbe Modellsport“ is a registered Trademark by Modellbau Lindinger GmbH Errors, misprints and technical changes reserved. Copyright 2019 Modellbau Lindinger 2019 Copy and reprint only with our permission.
Need help?
Do you have a question about the JetForce and is the answer not in the manual?
Questions and answers