Page 1: Installation Guide
H3C SR6604/SR6608 Routers Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: T2-08040D-20110810-C-1.09...
Page 2 SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V G, V G, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners Notice The information in this document is subject to change without notice.
Page 3 Preface The H3C SR6604/SR6608 Routers Installation Guide includes eight chapters, which describe the hardware features of the H3C SR6604/SR6608 Routers and provide examples to help you install the router. This preface includes: Audience • • Conventions About the H3C SR6600 documentation set •...
Page 4 Layer 2 forwarding and other Layer 2 features. Port numbering in examples The port numbers in this document are for illustration only and might be unavailable on your device. About the H3C SR6600 documentation set The H3C SR6600 documentation set includes: Category...
Page 5: Obtaining Documentation
Obtaining documentation You can access the most up-to-date H3C product documentation on the World Wide Web at http://www.h3c.com. Click the links on the top navigation bar to obtain different categories of product documentation: [Technical Support & Documents > Technical Documents] –...
Page 6: Table Of Contents
Contents Product overview·························································································································································· 1 SR6604 physical architecture··········································································································································1 SR6608 physical architecture··········································································································································3 Main processing units·······················································································································································5 Flexible interface platform modules ································································································································6 FIP-100 ······································································································································································7 FIP-110 ······································································································································································7 FIP-200 ······································································································································································8 FIP-210 ······································································································································································8 Service aggregation platform modules···························································································································9 SAP-48GBE ·······························································································································································9 SAP-24GBP ···························································································································································· 10 OAP cards ······································································································································································ 10 HIMs and MIMs······························································································································································ 10 Power supplies································································································································································...
Page 7 Installing an RSE-X1 MPU ····································································································································· 28 Installing a FIP module··················································································································································· 29 Installing a SAP/OAP ···················································································································································· 30 Installing a HIM ······························································································································································ 31 Installing a MIM ····························································································································································· 32 Installing a fan tray ························································································································································ 32 Installing a CF card························································································································································ 33 Installing a power supply ·············································································································································· 34 Connecting a power cord ·············································································································································...
Page 8 Replacement procedures ···········································································································································66 Safety recommendations ··············································································································································· 66 Replacing a power supply ············································································································································ 66 Replacing an RPE-X1 MPU ············································································································································ 67 Prerequisites ··························································································································································· 67 Replacing an MPU ················································································································································ 67 Replacing an RSE-X1 MPU ············································································································································ 68 Prerequisites ··························································································································································· 68 Replacing an MPU ················································································································································ 68 Replacing a FIP module ·················································································································································...
Page 9 Appendix A Technical specifications························································································································91 Dimensions and weight ················································································································································· 91 System power ································································································································································· 91 AC power supply ··························································································································································· 92 DC power supply ··························································································································································· 92 Fan tray ··········································································································································································· 92 MPU················································································································································································· 93 RPE-X1····································································································································································· 93 RSE-X1 ···································································································································································· 93 Components ··························································································································································· 94 FIP-100 ············································································································································································ 96 Technical specifications ········································································································································...
Page 10 Introduction ··························································································································································123 Ethernet twisted pair cable ·································································································································127 Optical fiber ·································································································································································127 E1 interface cable ························································································································································128 T1 interface cable ························································································································································129 CE3/CT3 interface cable············································································································································130 Serial port cable···························································································································································131 Appendix F AC power cables used in different countries or regions ································································· 134 10A AC power cables used in different countries or regions·················································································134 16A AC power cables used in different countries or regions·················································································137 Index ········································································································································································...
Page 11: Product Overview
Product overview This chapter describes the H3C SR6604 and SR6608 routers and includes these sections: SR6604 physical architecture • SR6608 physical architecture • Main processing units • • Flexible interface platform modules Service aggregation platform modules • OAP cards •...
Page 12 Figure 2 Front view (an RSE-X1 MPU installed) (1) MPU slot (slot 1) (2) MPU/service module slot (slot 2) (3) Service module slot (slot 3) (4) Power supply slots (5) PoE module slot (reserved) (6) Fan tray NOTE: • In this figure, one RSE-X1 MPU is installed. You can install one more RSE-X1 MPU or install one service module in the MPU/service module slot.
Page 13: Sr6608 Physical Architecture
SR6608 physical architecture Figure 4 Front view (an RPE-X1 carrier installed) (1) MPU slot (slot 0 and slot 1) (2) Service module slots (slot 2 through slot 5) (3) Fan tray (4) Power supply slots (5) PoE module slot (reserved) NOTE: In this figure, an RPE-X1 carrier that holds one RPE-X1 MPU is installed.
Page 14 Figure 5 Front view (an RSE-X1 MPU installed) (1) MPU slot (slot 1) (2) MPU/service module slot (slot 2) (3) Service module slot (slot 3 through slot 5) (4) Power supply slots (5) PoE module slot (reserved) (6) Fan tray NOTE: •...
Page 15: Main Processing Units
(RTC) function. The MPUs available for the SR6604 and SR6608 routers include half-slot wide RPE-X1 and one-slot wide RSE-X1. If you order an RPE-X1 MPU, you must also order an RPE-X1 carrier. For the MPU specifications, “Appendix A Technical...
Page 16: Flexible Interface Platform Modules
FIP to support different network services as needed. This section describes the flexible interface platform (FIP) modules available for the H3C SR6604 and SR6608 routers. When you order or install a FIP, see” Appendix B Hardware compatibility matrices” to check the FIP and...
Page 17 FIP-100 You can plug up to four MIMs into the FIP- 1 00 to provide high-density narrowband aggregation and protect the investment in the MIMs for MSR routers. Figure 9 FIP-100 front panel (1) Combo port 1 (2) Slot 4 (3) Slot 3 (4) OPEN BOOK mark (5) Slot 1...
Page 18 Table 2 References for FIP operations Operation Reference Install and remove the FIP “Installing a FIP module” and “Replacing a FIP module.” Install and remove MIMs “Installing a MIM” and “Replacing a MIM.” Connect network cables “Connect Ethernet cables.” Connect optical fibers “Connect Ethernet cables”...
Page 19: Service Aggregation Platform Modules
Service aggregation platform modules A service aggregation platform (SAP) module provides network ports for receiving packets from the network and sending packets to the network. This section describes the SAPs available for the H3C SR6604 and SR6608 routers. SAP-48GBE The SAP-48GBE has 48 high-performance RJ-45 ports that can be both routed and switched.
Page 20: Sap-24Gbp
Power supplies The H3C SR6604 and SR6608 routers can be DC-powered or AC-powered. You can install two power supplies in your router, and they must be the same model. The H3C SR6604 and SR6608 routers use hot swappable power supplies. You can install one power supply, or for redundancy, two power supplies for your routers.
Page 21: Dc-Input Power Supply
Figure 15 AC-input power supply front view (1) AC-input power receptacle (2) Power switch (3) Handle (4) Power supply status LED DC-input power supply The DC input voltage range is –48 VDC to –60 VDC. Figure 16 DC-input power supply front view (1) DC-input terminal block (2) Power switch (3) Handle...
Page 22: Fan Trays
Fan trays Figure 17 SR6604 fan tray (1) Fan tray status LED (RUN) (2) Alarm LED (ALM) (3) Fans (4) Handle Figure 18 SR6608 fan tray (1) Fan tray status LED (RUN) (2) Alarm LED (ALM) (3) Handle (4) Fans...
Page 23: Preparing For Installation
If there are two power inputs, disconnect the two power inputs to power off the router. • • Do not work alone when the router has power. Always check that the power has been disconnected. • Safety with laser The H3C SR6604 and SR6608 routers are a line of class 1 laser products.
Page 24: Safety With Router Moving
Examining the installation site The H3C SR6604 and SR6608 routers can only be used indoors. To ensure that the router works properly and to prolong its service lifetime, the installation site must meet the following requirements: Temperature and humidity •...
Page 25: Altitude
The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion and premature aging of components, as shown in Table Table 9 Harmful gas limits in an equipment room Max. (mg/m 0.006 0.05 0.01 Cooling system The H3C SR6604 and SR6608 routers adopt left to right airflow for heat dissipation.
Page 26: Esd Prevention
Figure 19 SR6604/SR6608 airflow Make sure there is enough space (greater than 10 cm (3.94 in)) around the air intake and outlet • vents on the router for good ventilation. Make sure the installation site has a good cooling system.
Page 27: Emi
Figure 20 Use an ESD-preventive wrist strap (1) ESD-preventive wrist strap (2) Lock (3) Alligator clip CAUTION: Check the resistance of the ESD-preventive wrist strap for safety. The resistance reading should be in the range of 1 to 10 megohm (Mohm) between human body and the ground. All electromagnetic interference (EMI) sources, from outside or inside of the router and application system, adversely affect the router in a conduction pattern of capacitance coupling, inductance coupling, electromagnetic wave radiation, or common impedance (including grounding system) coupling.
Page 28: Rack-Mounting
Make sure the grounding terminal of the AC power receptacle is well grounded. • • Install a lightning arrester at the input end of the power supply to enhance the lightning protection capability of the power supply. Install a special lightning arrester at the input end of outdoor signal lines (for example, E1/T1 line) •...
Page 29: Checklist Before Installation
Checklist before installation Table 10 Checklist before installation Item Requirements Result • There is a minimum clearance of 10 cm (3.9 in) around the inlet and exhaust vents for heat dissipation of the router chassis. Installation site Ventilation • A ventilation system is available at the installation site.
Page 30 Item Requirements Result • Install the router in an open rack if possible. If you install the router in a closed cabinet, make sure that the cabinet is equipped with a good ventilation system. Rack-mounting • The rack is sturdy enough to support the weight of requirements the router and installation accessories.
Page 31: Installing The Router
Installing the router This chapter includes these sections: Installation flow • Check before installation • Installing the router in a 19-inch rack • • Grounding the router Installing an MPU • Installing a FIP module • Installing a SAP/OAP • Installing a HIM •...
Page 32: Installation Flow
Installation flow Figure 21 H3C SR6604/SR6608 router installation flow Check before installation Follow these steps to prepare for installing an H3C SR6604 or SR6608 router: Make sure that you have read the chapter“Preparing for Installation” carefully and the installation •...
Page 33: Installing The Router In A 19-Inch Rack
Installing the router in a 19-inch rack The following uses a SR6604 as an example. Installing cage nuts to the rack Follow these steps to install cage nuts to the rack: Determine where to install the router in the rack, and then install a rack shelf to the rack.
Page 34: Installing The Cable Management Brackets
Installing the cable management brackets As shown in Figure 24, before installing a mounting bracket to the router, install the cable management bracket to the left mounting bracket with screws. Figure 24 Install the cable management bracket (1) Left mounting bracket (2) Cable management bracket Installing the mounting brackets to the router Before installing the router to a rack, install the front mounting brackets to the two sides of the router.
Page 35: Installing The Router To The Rack
Installing the router to the rack Follow these steps to install the router to the rack: Put the router on the rack shelf, and slide the router, making sure that there is enough clearance between Step1 the router and rack posts for installing the mounting brackets. Fix the router horizontally by fastening the mounting brackets to the rack with appropriate pan head Step2 screws.
Page 36: Installing An Mpu
Figure 27 Connect the grounding cable to the grounding hole of router NOTE: • The resistance reading should be smaller than 5 ohms between router chassis and the ground. To guarantee the grounding effect, use the grounding cable provided with the router to connect to the •...
Page 37 Figure 28 Internal structure of the RPE-X1 carrier Figure 29 Install the RPE-X1 carrier Gently push the RPE-X1 carrier (with the components facing up) into slot 1 along the slide rails until the Step4 positioning pins on the backplane are seated in the positioning holes at the bottom of the RPE-X1 carrier. Then push the ejector levers inward to lock the RPE-X1 carrier in position and fasten the captive screws on the ejector levers.
Page 38: Installing An Rse-X1 Mpu
Use even pressure to gently push the RPE-X1 into slot 1 along the slide rails, and then push the ejector Step5 levers inward to lock the board in position. Fasten the captive screws with a Philips screwdriver. Step6 If the router is powered off, power it on. Step7 The RUN LED (green) flashes fast (at 8 Hz).
Page 39: Installing A Fip Module
NOTE: number The RSE-X1 MPU is hot swappable and you must perform the remove slot command to stop the • module before you remove it. When two RSE-X1 MPUs are installed on the router, the ACT LED (green) is steady on. •...
Page 40: Installing A Sap/Oap
NOTE: number FIP modules are hot swappable and you must perform the remove slot command to stop the • module before you remove it. If you encounter a resistance when pushing a FIP module into slot, remove the filler panels at both sides •...
Page 41: Installing A Him
Power on the router. Step5 After the SAP module is powered on, the RUN LED (green) flashes once and then flashes fast (at 8 Hz). It flashes slowly (at 1 Hz) after the application is loaded. This means that the SAP module runs properly. NOTE: number SAPs are hot swappable and you must perform the remove slot...
Page 42: Installing A Mim
Installing a MIM Follow these steps to install a MIM: Locate the slot to install the MIM on the FIP module. The MIM should be installed in the lower slot on the Step1 FIP module. For more information see “Appendix D Arranging slots and numbering interfaces.”...
Page 43: Installing A Cf Card
Figure 36 Push the fan tray into the slot Caution Use a Phillips screwdriver to fasten the captive screws on the fan tray. Step3 Power on the router and check the status LED on the front panel. On means the fan tray is operating Step4 properly.
Page 44: Installing A Power Supply
Installing a power supply The procedures for installing an AC power supply and DC power supply are the same. The following uses an AC power supply as an example. Locate the slot to install the power supply. Use even pressure to gently push the power supply slowly Step1 along the slide rails into the slot.
Page 45: Connecting A Dc Power Cord
Connecting a DC power cord DC power cord Figure 40 DC power cord Connecting a DC power cord Follow these steps to connect a DC power cord: Make sure the power is OFF. Step1 Remove the protection cover of the DC power supply. Step2 Connect the end marked with “–...
Page 46: Connect Ethernet Cables
Connect Ethernet cables Connecting a copper Ethernet cable Follow these steps to connect the router to a network through a 10/100/1000Base-T port: Plug one end of an Ethernet twisted pair cable into the copper Ethernet port (RJ-45 port) to be connected Step1 on the router and the other end of the cable into the Ethernet port of the peer device.
Page 47 Figure 42 Remove the dust plug Install the transceiver module, as shown in Figure Step2 Figure 43 Install the transceiver module Remove the dust cover on the transceiver module and the protective caps on the LC connectors. Step3 Plug the LC connectors on one end of the fiber cable into the Rx and Tx ports, and plug the LC connectors Step4 on the other end to the Tx and Rx ports on the peer device, as shown in Figure...
Page 48 Figure 44 Connect the fiber connectors After power on the router,check whether the LEDs of the optical interfaces are normal. Step5...
Page 49: Installing Optional Components
Installing optional components NOTE: Optional components are not provided with the router. Purchase them as needed. This chapter includes these sections: Installing an air filter • Installing a fiber management tray • Installing a port lightning arrestor • • Installing a power lightning arrester (lightning protection busbar) Installing a signal lightning arrester •...
Page 50: Installing A Fiber Management Tray
Figure 46 Insert the air filter Fasten the captive screws with a Philips screwdriver. Step6 Figure 47 Fasten the captive screws Installing a fiber management tray Preparations Confirm the following prerequisites: The rack is fixed. • • The router is installed. The installation involves the following materials: •...
Page 51: Installing A Port Lightning Arrestor
Before connecting an outdoor Ethernet cable to an Ethernet port, install a port lightning arrester to protect the router against lightning strokes. The following port lightning arrester can be installed on the SR6604 or SR6608. The specifications for the port lightning arrester are as follows: Port protective unit: Single port •...
Page 52 Cut short the grounding cable of the port lightning arrester according to its distance to the grounding Step2 screw. Then, fix the grounding cable onto the grounding screw of the router. Use a multimeter to check the connection between the grounding cable of the port lightning arrester and Step3 the grounding screw of the router.
Page 53: Installing A Power Lightning Arrester (Lightning Protection Busbar)
Installing a power lightning arrester (lightning protection busbar) Before connecting an outdoor AC power supply to the router, install a lightning protection busbar at the AC power input end and then connect the AC power cord to a lightning protection busbar to protect the router against lightning strokes.
Page 54: Installing A Signal Lightning Arrester
Before installing a signal lightning arrester, consider such performance indexes of the lightning arrester as lightning protection, bandwidth, transmission loss, and port type. The SR6604/SR6608 supports the following types of signal lightning arresters: • Voltage-limiting protection – signal lightning arrester – maximum discharge current 2.5KA/protection voltage 25V--SMB-75J/ SMB-75J- 1 W- 1 0Mbps...
Page 55 Figure 51 Install a port lightning arrester Precautions The performance of the signal lightning arrester may be affected in the following cases: • The IN and OUT ends of the signal lightning arrester are connected incorrectly. The IN end should be connected to the external cable, and the OUT end to the Ethernet port of the router.
Page 56: Logging In To The Router And Configuring Basic Settings
Plug the DB-9 female connector to the serial port of the configuration terminal. Step2 Connect the RJ-45 connector to the console port of the router. Step3 The console cable connection procedures are the same for the SR6604 and SR6608. The following uses an SR6608 as an example.
Page 57: Setting Terminal Parameters
Figure 52 Connect the console cable CAUTION: When you disconnect a PC from a powered-on router, disconnect the DB-9 connector of the console cable from the PC after disconnecting the RJ-45 connector from the router. Setting terminal parameters To configure and manage the router, you must run a terminal emulator program on the configuration terminal, for example, a PC.
Page 58 Figure 53 Connection description of the HyperTerminal Type the name of the new connection in the Name text box and click OK. The following dialog box Step2 appears. Select the serial port to be used from the Connect using drop-down list. Figure 54 Set the serial port used by the HyperTerminal connection Click OK after selecting a serial port and the following dialog box appears.
Page 59 Figure 55 Set the serial port parameters Click OK after setting the serial port parameters and the system enters the following interface. Step4 Figure 56 HyperTerminal window Click Properties in the HyperTerminal window to enter the aaa Properties dialog box. Click the Settings Step5 tab, set the emulation to VT100, and then click OK.
Page 60: Powering On The Router
Figure 57 Set terminal emulation in aaa Properties dialog box Powering on the router Checking before power-on Before powering on the router, verify the following items: The power cord and grounding cable are properly connected. • The power source voltage meets the requirement of the router. •...
Page 61: Displaying Boot Information
Power on the router, and you can see the following information: System start booting... Booting Normal Extend BootWare..**************************************************************************** H3C SR6600 Router BootWare, Version 1.39 **************************************************************************** Copyright (c) 2004-2011 Hangzhou H3C Technologies Co., Ltd. Compiled Date : Jan 13 2011 CPU Type : MPC8548E CPU L1 Cache...
Page 62: Logging In To The Router Through Telnet
Specify an IP address for the PC, make sure that the PC and the interface are in the same network Step3 segment. NOTE: H3C SR6600 Routers For more information about how to log in to the router through Telnet, see the Configuration Guides Logging to the router through the AUX port...
Page 63: Configuring Basic Settings
Configuring basic settings Follow these steps to configure basic settings for the router: To do… Use the command… Remarks Optional Set the current time and date clock datetime time date Available in user view Required Enter system view system-view Available in user view interface interface-type Enter Ethernet interface view —...
Page 64: Hardware Management And Maintenance
Comware Software, Version 5.20, R0600 Copyright (c) 2010 Hangzhou H3C Technologies Co., Ltd. H3C SR6608 uptime is 0 week, 0 day, 0 hour, 6 minutes Slot 0: RPE-X1 uptime is 0 week, 0 day, 0 hour, 6 minutes CPU type: FREESCALE MPC8548 1000MHz...
Page 65: Displaying The Operational Statistics Of The Router
[FIXED PORT] MGE0/0/0 (Hardware)Ver.B, (Driver)1.0, (Cpld)133.0 Slot 5: FIP-210 uptime is 0 week, 0 day, 0 hour, 4 minutes CPU type: RMI XLR732 1000MHz 1024M bytes DDR2 SDRAM Memory 4M bytes Flash Memory 0K bytes NVRAM Version: Ver.A Logic Version: 136.0 Basic BootWare Version: 1.14 Extend BootWare Version: 1.22...
Page 66: Displaying The Detailed Information About A Module
Displaying the detailed information about a module Use the display device verbose command to display detailed information of modules in each slot. <Sysname>display device verbose System-mode(Current/After Reboot): Normal/Normal Slot No. Board type Status Primary SubSlots --------------------------------------------------------------------- RPE-X1 Normal Master Absent Absent Absent Absent...
Page 67: Displaying The Cpu Usage Of A Module
VENDOR_NAME:H3C Slot 5: DEVICE_NAME:NONE DEVICE_SERIAL_NUMBER:NONE MAC_ADDRESS:NONE MANUFACTURING_DATE:NONE VENDOR_NAME:H3C Use the display device manuinfo slot slot-number command to display the electrical label information of the module in the specified slot. <Sysname> display device manuinfo slot 5 Slot 5: DEVICE_NAME:NONE DEVICE_SERIAL_NUMBER:NONE MAC_ADDRESS:NONE...
Page 68: Displaying The Memory Usage Of A Module
Table 13 Output description Field Description CPU usage of the module in slot 0. If the module in the slot has multiple CPUs, Slot 0 CPU usage shows the Slot 0 CPU usage usage of the main CPU of the module in slot 0, and Slot 0 CPU 1 CPU usage shows the usage of the standby CPU of the module in slot 0.
Page 69: Displaying The Operational Status Of The Fan
Field Description Operational status of the CF card: • Absent—No CF card is present in the slot. Status: • Fault—The CF card fails. • Normal—The CF card is operating properly. Size: Storage capacity of the CF card Displaying the operational status of the fan Use the display fan command to display the operational status of the fan.
Page 70: Port Configuration And Management
To do… Use the command… Remarks Enter system view system-view — Optional Display the temperature display environment information of your router Available in any view Port configuration and management Configuring a combo interface Combo interface overview A combo interface is a logical interface comprising an SFP port of a transceiver module and an RJ-45 Ethernet port.
Page 71: Displaying Transceiver Module Information And Alarming Information
The system outputs alarm information for you to locate and troubleshoot faults of transceiver modules. For the H3C-customized transceiver modules, the system can also monitor the key parameters, such as temperature, voltage, laser bias current, TX power, and RX power. When these parameters are abnormal, you can take corresponding measures to prevent transceiver module faults.
Page 72: Active And Standby Switchover For Mpus
MPU are real-time synchronized (copied) to the standby MPU, so that the active MPU and the standby MPU can have the same configurations. Do not use the H3C SR6602-specific software to upgrade the H3C SR6604/6608 routers. Otherwise, •...
Page 73: Solving System Faults
Solving system faults Solving system faults When the system detects faults (such as system instruction faults, invalid addresses, data overflow, null pointers, and division by zero operations) during the operation of the active MPU or standby MPU, you can solve the problem in one of the following methods: reboot: Rebooting the failed MPU so that the MPU restores to normal operational status.
Page 74: Rebooting A Module Or Router
during the process. The safe saving mode is preferred in environments where a stable power supply is unavailable or remote maintenance is involved. Follow these steps to save the current configuration of the router: To do… Use the command… Remarks Save the current configuration to the specified file, but the save file-url [ all | slot slot-number ]...
Page 75 To do… Use the command… Remarks Enable the scheduled reboot Use either command function and specify a specific schedule reboot at hh:mm [ date ] reboot time and date The scheduled reboot function is disabled by default. Enable the scheduled reboot schedule reboot delay { hh:mm | function and specify a reboot Available in user view...
Page 76: Replacement Procedures
Replacement procedures The H3C SR6604 and SR6608 routers use a modular, all-pluggable design, and support replacing hot swappable modules without interrupting the router operation. This chapter includes these sections: Safety recommendations • • Replacing a power supply Replacing an RPE-X1 MPU •...
Page 77: Replacing An Rpe-X1 Mpu
If the router is configured with two MPUs, make sure both MPUs operate properly before replacing any MPU. To replace the active MPU, H3C recommends that you execute the slave switchover command in • the system view of the active MPU to trigger an active and standby switchover. For more information about the slave switchover command, see the H3C SR6600 Routers High Availability Command Reference.
Page 78: Replacing An Rse-X1 Mpu
MPU. • To replace the active MPU, H3C recommends that you execute the slave switchover command in the system view of the active MPU to trigger active/standby switchover. For more information about the slave switchover command, see the H3C SR6600 Routers High Availability Command Reference.
Page 79: Replacing A Fip Module
Figure 60 Pull the RSE-X1 MPU out of the slot If you do not install a new MPU in the slot, install a blank panel. To install a new MPU, see “Installing an Step4 RSE-X1 MPU.” Replacing a FIP module CAUTION: When the RUN LED of the FIP module is fast flashing, do not unplug the FIP module.
Page 80: Replacing A Sap/Oap Module
Figure 61 Pull the FIP module out of the slot If you do not install a new FIP module in the slot, install a blank panel. To install a new FIP module, see Step4 “Installing a FIP module.” Replacing a SAP/OAP module CAUTION: When the RUN LED of the SAP/OAP module is fast flashing, do not unplug the module.
Page 81: Replacing A Him
Figure 62 Pull the SAP module out of the slot If you do not install a new SAP module in the slot, install a blank panel. To install a new SAP module, see Step4 “Installing a SAP/OAP.” Replacing a HIM Follow these steps to replace a HIM: Determine the HIM to be removed.
Page 82: Replacing A Mim
Replacing a MIM Follow these steps to replace a MIM: Determine the MIM to be removed. Use a flat-blade screwdriver to completely loosen the captive screws Step1 of the MIM to be removed. Holding the handle of the MIM, gently pull the MIM out of slot along the slide rails. Step2 Figure 64 Pull the MIM out of the slot If you do not install a new MIM in the slot, install a blank panel.
Page 83: Replacing A Transceiver Module
As shown in Figure 65, press the CF card eject button of the CF card reader so that the eject button Step2 protects from the panel. Figure 65 Press the eject button Press the eject button again to eject the CF card part-way out of the CF card reader, and then pull the CF Step3 card out of the CF card reader.
Page 84: Replacing A Fan Tray
As shown in Figure 67, holding the handle of the transceiver module, gently pull the transceiver module Step3 out. Insert the plastic plug to the removed transceiver module, and put the transceiver module into its original Step4 shipping materials. If you do not install a new transceiver module in the interface, install a dust-proof plug in the interface. Step5 To install a transceiver module, see “Connect Ethernet...
Page 85: Replacing An Air Filter
Figure 68 Pull out the fan tray Install a new fan tray. For more information, see “Installing a fan tray.” Step3 NOTE: Do not keep the router working without a fan tray formore than two minutes because poor ventilation • may result in damage to the router.
Page 86: Replacing A Memory Module
Figure 69 Loosen the captive screws of the air filter Gently pull the air filter out along the slide rails. Step2 Figure 70 Pull the air filter out along the slide rails Install a new air filter. For more information, see “Installing optional components.”...
Page 87: When To Replace A Memory Module
• An existing memory module is damaged. CAUTION: Use the memory modules provided by H3C only. Otherwise, the router may be unable to operate • properly. • For all the MPUs and service modules, except RPE-X1 MPU, memory modules with the same capacity must be used in pairs, for the specifications of memory modules supported, see “Appendix A Technical...
Page 88: Memory Module Structure
Memory module structure Figure 72 Memory module structure (a ) Front view (b ) Rear view (1) Connector edge (2) Polarization notch (3) Latch notch Memory module slot Figure 73 Memory module slot (1) Release latch (2) Memory module slot Replacing a memory module Follow these steps to replace a memory module: Determine the module (MPU or FIP) for which you will replace a memory module, and put the module on...
Page 89 Figure 74 Remove the memory module CAUTION: Do not touch the surface-mounted components of the memory module directly with your hands to avoid • damaging the memory module. Hold the memory module only at its non-conductive edge. To protect the removed memory module, place it in an antistatic bag. •...
Page 90: Troubleshooting
Troubleshooting This chapter includes these sections: MPU failures • FIP module failures • Power supply failures • • Fan failures HIM/MIM failures • Configuration system problems • Password loss • Cooling system failure • • Interface module, cable, and connection failure Software upgrade failures •...
Page 91: Alm Led Is Steady On Or Flashes
For example, the ALM LED is on when the system is over-temperature. In this case, the system displays the following output: %Jun 25 14:38:45:444 2010 H3C DRVMSG/3/TempCritical: CPU temperature critical in Slot 3, index is 1. To solve the problem, check the output (such as the system temperature and PCB voltage alarms) on the serial terminal and the software management tool.
Page 92: Run Led Fast Flashes
Slot3: The Board is present, state is unknown Contact your local sales agent. Step4 RUN LED fast flashes 20 minutes after the router is powered on or the FIP module is plugged into the router, if the RUN LED of the FIP module still fast flashes at 8 Hz, it indicates that the FIP module application program fails to start or the FIP module is faulty.
Page 93: Alm Led Is Red
5 14:59:03:878 2010 H3C DRVMSG/3/FanPlugIn:Fan 1 Plug In. %Jul 5 14:59:03:879 2010 H3C DRVMSG/3/FanErr:Fan 1 Error. #Jul 5 14:59:03:998 2010 H3C DEV/1/FAN STATE CHANGES TO FAILURE: Trap 1.3.6.1.4.1.2011.2.23.1.12.1.6<fanfailure>: fan ID is 1 %Jul 5 14:59:03:998 2010 H3C DEV/4/FAN FAILED: Fan 1 failed.
Page 94: Configuration System Problems
Configuration system problems If the configuration environment setup is correct, the configuration terminal displays boot information when the router is powered on. If the setup is incorrect, the configuration terminal displays nothing or garbled text. No terminal display If the configuration terminal displays nothing when the router is powered on, follow these steps to troubleshoot the failure: Check the following items.
Page 95: User Password Loss
When the main BootWare menu appears again, and select 0 to reboot the system. Step2 System is rebooting now. System start booting... Booting Normal Extend BootWare..Set a new password in system view after the system reboots. Step3 <H3C> system-view [H3C] user-interface console 0 [H3C-ui-console0] authentication-mode password [H3C-ui-console0] set authentication password simple 123456...
Page 96: Super Password Loss
To save the new password, execute the save command after modifying the user password. • • H3C recommends saving the modification as the default configuration file. Super password loss The super password enables you to switch between four super levels. In the case of super password loss, you cannot perform higher level operations.
Page 97: Cooling System Failure
%May 14 21:37:35:271 2010 H3C DRVMSG/3/Temp2High: Environment temperature too high in Slot 0, index is 2. #May 14 21:37:35:713 2010 H3C DEV/1/BOARD TEMPERATURE UPPER: Trap 1.3.6.1.4.1.2011.2.23.1.12.1.16<hwBoaardTemperatureHigher>: frame Index is 0, slot Index 0.0 %May 14 21:37:35:713 2010 H3C DEV/4/BOARD TEMP TOOHIGH: Board temperature is too high on Frame 0 Slot 0, type is MPU.
Page 98: Interface Module, Cable, And Connection Failure
If the temperature inside the router exceeds 90°C (194°F), power off the router immediately and contact Step4 your local sales agent. NOTE: H3C SR6600 Routers For more information about the display environment command, see the Fundamentals Command Reference Interface module, cable, and connection failure After an HIM/MIM is installed and the router is powered on, the LEDs on the HIM/MIM panel may indicate abnormal operation.
Page 99: Ftp Upgrade Failure
Can't connect to the remote host To solve this problem, configure the network port correctly, and make sure that the network port is up and you can successfully ping the TFTP server from the network port. NOTE: The barcode stuck on the router chassis contains production and servicing information. Before you return a faulty router for serving, provide the barcode information of the router to your local sales agent.
Page 100 Booting App fails! The name of the main, backup, and secure application files vary by user settings. A possible reason for the errors is that the main, backup, and secure application files have been deleted or damaged. To solve this problem, download the application package again or set the file properties in the BootWare file list.
Page 101: Appendix A Technical Specifications
40 × 140 × 354 mm (1.57 × 5.51 ×13.94 in) W × D) Two power supply slots are provided. The power supplies must have the same Power supply slots specifications. Power • SR6604—54 W to 410 W consumption • SR6608—61 W to 780 W range Hot swapping Supported...
Page 102: Ac Power Supply
Dimensions (H × W × D) 40 × 140 × 350 mm (1.57 × 5.51 × 13.78 in) Fan tray Table 24 Fan tray specifications Specification Fan (built-in) SR6604 SR6608 Rated voltage 12 VDC Total fan power 30 W consumption...
Page 103: Mpu
RPE-X1 Table 25 RPE-X1 specifications Item Specification Flash 4 MB DDR2 SDRAM Memory type and size 1 GB (default, one memory module) 2 GB (maximum, two memory modules) NVRAM 128 KB Console port 9600 bps (default) to 115200 bps AUX port 9600 bps (default) to 115200 bps Management Ethernet 1 (10Base-T/100Base-TX/1000Base-T)
Page 104: Components
256 MB 512 MB • 1 GB • CAUTION: Use CF cards provided by H3C only. The router may be incompatible with other CF cards. • • CF cards less than 256 MB are not supported. Console port Introduction The router provides an RS232 asynchronous serial console port that can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.
Page 105 Table 27 Console port specifications Item Specification Connector RJ-45 Standard compliant Asynchronous EIA/TIA-232 Baud rate 9600 bps (default) to 115200 bps Transmission distance ≤ 15 m (49.21 ft) • Provides connection to an ASCII terminal • Provides connection to the serial port of a local PC to run the terminal Services emulation program •...
Page 106: Technical Specifications
Item Specification 10 Mbps, half/full-duplex Interface speed and duplex mode 100 Mbps, half/full-duplex 1000 Mbps, full-duplex Category-5 twisted pair with a maximum transmission Interface cable and maximum transmission distance distance of 100 m (328.08 ft) Used for router software upgrade and network Function management NOTE:...
Page 107: Maximum Interface Modules Provided By Fip-100S In Full Configuration
H3C SR6600 Routers information about the combo enable { copper | fiber } command, see the Interface Command Reference Use transceiver modules provided by H3C only. The router may be incompatible with other transceiver • modules and thus displays alarms automatically.
Page 108: Technical Specifications
H3C SR6600 Routers information about the combo enable { copper | fiber } command, see the Interface Command Reference Use transceiver modules provided by H3C only. The router may be incompatible with other transceiver • modules and thus displays alarms automatically.
Page 109: Maximum Interface Modules Provided By Fip-110S In Full Configuration
Maximum interface modules provided by FIP-110s in full configuration Table 33 Maximum interface modules provided by FIP-110s in full configuration Interfa One RPE-X1 Two RPE-X1s One RSE-X1 Two RSE-X1s modul SR6604 SR6608 SR6604 SR6608 SR6604 SR6608 SR6604 SR6608 FIP-110 supporte...
Page 110: Maximum Interface Modules Provided By Fip-200S In Full Configuration
{ copper | fiber } command, see the Interface Command Reference • Use transceiver modules provided by H3C only. The router may be incompatible with other transceiver modules and thus displays alarms automatically. Maximum interface modules provided by FIP-200s in full...
Page 111: Maximum Interface Modules Provided By Fip-210S In Full Configuration
H3C SR6600 Routers information about the combo enable { copper | fiber } command, see the Interface Command Reference Use transceiver modules provided by H3C only. The router may be incompatible with other transceiver • modules and thus displays alarms automatically.
Page 112: Sap-24Gbp
Item Specification DDR2 SDRAM • 2 GB (default, two 1 GB memory modules) Memory type and size • 4 GB (maximum, two 2 GB memory modules) Use two DDR2 SDRAM modules with the same memory size at a time. NVRAM 128 KB Max power consumption 200 W...
Page 113: Port Lightning Arrester
The transceiver modules are optional to be separately ordered if needed. Use transceiver modules provided by H3C only. The router may be incompatible with other transceiver modules and thus displays alarms automatically. When working with SFP transceiver modules, the SAP-24GBP must use an optical fiber with LC-type connectors.
Page 114: Power Lightning Arrester
Before connecting an outdoor AC power to the router, install a lightning protection busbar at the AC power input end and then connect the AC power cord to a lightning protection busbar to protect the router against lightning strikes. In a heavy lightning area, H3C recommends installing a power lightning arrester.
Page 115: Appendix B Hardware Compatibility Matrixes
Appendix B Hardware compatibility matrixes In the compatibility matrixes, “√” means “Supported” and “×” means “Not supported.” FIP and router compatibility matrix Table 40 FIP and router compatibility matrix SR6604 SR6608 FIP-100 √ √ FIP-110 √ √ FIP-200 √ √...
Page 116: Interface Module And Fip Compatibility Matrix
Interface modules SR6604 SR6608 MIM-1ATM-OC3 √ √ MIM-2SAE √ √ MIM-4SAE √ √ MIM-8SAE √ √ MIM-IMA-4E1 √ √ MIM-IMA-8E1 √ √ MIM-IMA-4T1 √ √ HIMs HIM-8FE √ √ HIM-4GBE √ √ HIM-8GBE √ √ HIM-4GBP √ √ HIM-8GBP √...
Page 117: Interface Module And Transceiver Module Compatibility Matrix
Interface module FIP-100 FIP-110 FIP-200 FIP-210 × × √ √ Interface module and transceiver module compatibility matrix Table 44 Interface module and transceiver module compatibility matrix 10/100/ 1000 1000 100/100 Mbps 2.5 Gbps 10 Gbps Mbps Mbps Mbps 0 Mbps fiber-to-c fiber fiber...
Page 118: Sap/Oap And Mpu Compatibility Matrix
10/100/ 1000 1000 100/100 Mbps 2.5 Gbps 10 Gbps Mbps Mbps Mbps 0 Mbps fiber-to-c fiber fiber Interface fiber fiber fiber SFP fiber opper transceiv transceiv modules transceiv transceiv transceiv transceiv conversio n SFP module module module module module module copper module HIM-1EXP...
Page 119: Appendix C Leds
Appendix C LEDs H3C SR6604 and SR6608 routers provide MPU LEDs, FIP LEDs, and power supply LEDs to indicate the operating status of MPUs, FIPs, and power supplies. Table 46 LEDs of the H3C SR6604 and SR6608 routers Remarks Run LED (RUN)
Page 120: Mpu Leds
MPU LEDs Figure 76 LEDs on the RPE-X1 Table 47 RPE-X1 LED description Status Description No power input is available, or the RPE-X1 has failed. Slow flashing (1 The RPE-X1 is operating properly. Run LED (green) The application software is being loaded (in this case, Fast flashing (8 never power off the device or hot-swap the RPE-X1;...
Page 121 Status Description No CF card is present or the CF card is not recognizable. CF card LED A CF card is in position and has been detected. (green) The system is accessing the CF card. In this state, do not Flashing remove the CF card.
Page 122: Fip Leds
Status Description No power input is available, or the RSE-X1 has failed. Slow flashing The RSE-X1 is operating properly. (1 Hz) Run LED (green) The application software is being loaded (in this case, Fast flashing (8 never power off the device or hot-swap the RSE-X1; otherwise the RSE-X1 may be damaged).
Page 123 Figure 80 FIP-200 LEDs Figure 81 FIP-210 LEDs Table 49 FIP LED description Status Description No link is present. Solid green A 1000 Mbps link is present. 10/100/100 Data is being received or transmitted at a rate of Flashing green 0 Mbps copper 1000 Mbps.
Page 124: Sap Leds
Status Description No link is present. Solid green A link is present. 1000 Mbps fiber Ethernet Data is being sent or received at a rate of 1000 Flashing green port LED Mbps. (yellow/green) Solid yellow The transceiver module failed to be detected. SAP LEDs Figure 82 SAP LEDs(SAP-48GBE) Table 50 SAP-48GBE LED description...
Page 125: Him/Mim Leds
Data is being received or transmitted at a rate of 100 Flashing yellow Mbps. HIM/MIM LEDs For description of HIM/MIM LEDs, see the H3C SR6600 Routers Interface Module Guide. Power supply LEDs Figure 84 AC power supply LED Figure 85 DC power supply LED...
Page 126: Fan Tray Leds
Status Description The power supply is working Solid green properly. Power LED Solid red The power supply is faulty. No power is input. Fan tray LEDs Figure 86 Fan tray of the SR6604 Figure 87 Fan tray of the SR6608...
Page 127 Table 53 Fan tray LED description Status Description The system is powered off or the fan tray is faulty. Run LED (green) The fan tray is working properly. The fan tray is working properly. Alarm LED The fan tray is faulty. (red)
Page 128: Appendix D Arranging Slots And Numbering Interfaces
The router provides many types of interfaces, such as console, AUX, GigabitEthernet, serial (synchronous), POS, and E1 ports. This chapter describes how these interfaces are numbered. Figure 88 Slot arrangement on the SR6604 configured with an RPE-X1 Figure 89 Slot arrangement on the SR6604 configured with an RSE-X1...
Page 129 Figure 90 Slot arrangement on the SR6608 configured with an RPE-X1 Figure 91 Slot arrangement on the SR6608 configured with an RSE-X1 NOTE: The numbers in Figure 88 through Figure 91 represent corresponding slot numbers. • • On a router configured with an RSE-X1, slots are numbered from slot 1 instead of slot 0.
Page 130: Slot Arrangement For Mpus And Interface Modules
• interface-type: Type of the interface such as GE port and serial port. X: Number of the slot where the FIP/SAP resides, in the range of 2 to 3 on the SR6604 and 2 to 5 • on the SR6608.
Page 131: Examples
Examples Example 1 A FIP- 1 00 is installed in slot 3 and a MIM-2GBE module is installed on the FIP- 1 00. Fixed GigabitEthernet interfaces on the FIP-100 • GigabitEthernet 3/0/0 GigabitEthernet 3/0/1 • NOTE: The sub-slot number Y of fixed GE interfaces on a FIP is 0. GigabitEthernet interfaces on the MIM-2GBE If the MIM-2GBE is installed in slot 1 of the FIP-100, the GigabitEthernet interfaces are: GigabitEthernet 3/1/0...
Page 132: Example 4
GigabitEthernet interfaces on the HIM-4GBE If the HIM-4GBE is installed in slot 1 of the FIP-200, the GigabitEthernet interfaces are: • GigabitEthernet 3/1/0 GigabitEthernet 3/1/1 • GigabitEthernet 3/1/2 • GigabitEthernet 3/1/3 • If the HIM-4GBE is installed in slot 2 of the FIP-200, the GigabitEthernet interfaces are: •...
Page 133: Appendix E Cables
Appendix E Cables The H3C SR6604 and SR6608 support various types of MPUs and interface modules. The port types vary by the MPU and interface module model. Use dedicated cables to connect the ports of different types. Table 55 Cables...
Page 134 Figure 92 RJ-45 connector pinout NOTE: The RJ-45 Ethernet ports of the H3C SR6604 and SR6608 routers use category 5 or higher Ethernet twisted pair cables for connection. EIA/TIA cabling specifications define two standards, 568A and 568B, for cable pinouts.
Page 135 Figure 93 Straight-through cable white/orange orange white/green blue white/blue green white/brown brown Straight-through cable white/orange orange white/green blue white/blue green white/brown brown Figure 94 Crossover cable white/orange orange white/green blue white/blue green white/brown brown Crossover cable white/green green white/orange blue white/blue orange white/brown...
Page 136 Table 57 RJ-45 MDI port pinouts 10Base-T/100Base-TX 1000Base-T Signal Function Signal Function Bi-directional data Sends data BIDA+ cable A+ Bi-directional data Sends data BIDA- cable A- Bi-directional data Receives data BIDB+ cable B+ Bi-directional data Reserved BIDC+ cable C+ Bi-directional data Reserved BIDC- cable C-...
Page 137: Ethernet Twisted Pair Cable
If an RJ-45 Ethernet port is enabled with MDI/MDIX autosensing, it can automatically negotiate pin roles. NOTE: The H3C SR6604 and SR6608 RJ-45 Ethernet ports support MDI/MDIX autosensing. By default, MDI/MDIX autosensing is enabled on an interface. Ethernet twisted pair cable Follow these steps to make an Ethernet twisted pair cable: Cut the cable to a proper length with the crimping pliers.
Page 138: E1 Interface Cable
Before connecting an optical fiber, make sure that the connector and cable type match the hot swappable interface module. NOTE: Some cards of the H3C SR6604/SR6608 router provide shielded covers for the fiber ports (such as SFP • ports). Before using such fiber ports, remove the shielded covers. Keep the shielded covers properly.
Page 139: T1 Interface Cable
Figure 96 4E1 conversion cable Figure 97 8E1 conversion cable DB68 NOTE: The coaxial connector and 75-ohm E1 trunk cable are optional accessories, and must be purchased separately if needed. T1 interface cable You can use a 4T1 interface cable to connect the MIM-IMA-4T1 module, and 8T1 to connect the MIM-8T1/MIM-8T1-F module.
Page 140: Ce3/Ct3 Interface Cable
• insertion, which may damage the interface module or even the host. H3C recommends installing a special lightning arrester at the input end of the 4T1/8T1 cables to protect • them against lightning strikes more efficiently when they are led outdoors.
Page 141: Serial Port Cable
Figure 100 E3/T3 cable CAUTION: H3C recommends installing a special lightning arrester at the input end of the E3/T3 cables to protect them against lightning strikes more efficiently when they are led outdoors. Serial port cable You can use a serial port cable to connect the MIM-2SAE/MIM-4SAE/MIM-8SAE module. Select a serial port cable according to the link type.
Page 142 Figure 103 V.35 DTE cable Figure 104 V.35 DCE cable Figure 105 X.21 DTE cable Figure 106 X.21 DCE cable...
Page 143 Figure 107 RS449 DTE cable Figure 108 RS449 DCE cable Figure 109 RS530 DTE cable Figure 110 RS530 DCE cable...
Page 144: Appendix F Ac Power Cables Used In Different Countries Or Regions
Appendix F AC power cables used in different countries or regions 10A AC power cables used in different countries or regions Table 61 10A AC power cables used in different countries or regions Countries or regions Countries or where the type of power Other countries or Connecto regions seldom...
Page 145 Holland, Denmark, Sweden, Finland, 04041056 (3 Indonesia, Turkey, F type Norway, Germany, India m, i.e., 9.8 ft) Russia, and CIS France, Austria, Belgium, and Italy Connector outline Power cable outline Connector outline Countries or regions Countries or where the type of power Other countries or Connecto regions seldom...
Page 146 Countries or regions Countries or where the type of power Other countries or Connecto regions seldom cables conforms to local regions using this type of Code (Length) r type using this type of safety regulations and power cables power cables can be used legally 04040888 (3 I type...
Page 147: Ac Power Cables Used In Different Countries Or Regions
16A AC power cables used in different countries or regions Table 62 16A AC power cables used in different countries or regions Countries or regions Countries or where the type of power Other countries or Connect regions seldom Code (Length) cables conforms to local regions using this type of or type...
Page 148 Connector outline Power cable outline Connector outline Countries or regions Countries or where the type of power Other countries or Connect regions seldom Code (Length) cables conforms to local regions using this type of or type using this type of safety regulations and power cables power cables...
Page 149: Index
Index A C D E F G H I L M N O P R S T Flexible interface platform modules,6 AC power supply,92 Active and standby switchover for MPUs,62 Grounding the router,25 Application file missing errors,89 HIM/MIM failures,83 CE3/CT3 interface cable,130 HIM/MIM LEDs,1 15...
Page 150 Slot arrangement for MPUs and interface modules,120 Powering on the router,50 Software upgrade failures,88 Solving system faults,63 Rebooting a module or router,64 SR6604 physical architecture,1 Replacing a CF card,72 SR6608 physical architecture,3 Replacing a fan tray,74 System power,91 Replacing a FIP...

This manual is also suitable for:

Sr6608

H3C SR6604 Installation Manual

Product Overview

Preparing for Installation

Installing the Router

Installing Optional Components

Logging in to the Router and Configuring Basic Settings

Hardware Management and Maintenance

Replacement Procedures

Troubleshooting

Appendix A Technical Specifications

Appendix B Hardware Compatibility Matrixes

Appendix C Leds

Appendix D Arranging Slots and Numbering Interfaces

Appendix E Cables

Appendix F AC Power Cables Used in Different Countries or Regions

Index

Quick Links

Installation Guide

Related Manuals for H3C SR6604

Summary of Contents for H3C SR6604

This manual is also suitable for:

Table of Contents