Subscribe to Our Youtube Channel
Related Manuals for Clarke CIR450
Summary of Contents for Clarke CIR450
- Page 1 PROFESSIONAL CORDLESS IMPACT WRENCH Model CIR450 Part No 4500630 OPERATING & MAINTENANCE INSTRUCTIONS GC0309...
-
Page 2: Introduction
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. -
Page 3: Table Of Contents
Accessories ..................14 Declaration of Conformity ..............15 COMPONENT INVENTORY The CIR450 is a professional, cordless impact wrench which is rechargeable using the mains power adaptor. Upon receipt, unpack and lay out the components, checking against the following list. Any damage or deficiency should be reported to your CLARKE dealer immediately. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Dress appropriately - do not wear loose clothing or jewellery. Tie long hair out of the way. 3. Keep children and visitors away - do not let children handle the wrench. 4. - Page 5 20. NEVER attempt to wipe the machine clean with solvents. Wipe plastic parts with a soft cloth, slightly dampened with soapy water. 21. NEVER attempt any repairs yourself. If you have a problem with this product contact your local CLARKE dealer. IMPACT WRENCH SAFETY INSTRUCTIONS ALWAYS use the impact wrench in the manner and for the functions described in these instructions.
-
Page 6: Electrical Connections
3. Should you wish to replace the fuse cover, ensure that the correct replacement is used (as indicated by marking or colour code). 4. Replacement fuse covers can be obtained from your local Clarke dealer or most electrical stockists. FUSE RATING The fuse in the plug must be replaced with one of the same rating and this replacement must be ASTA approved to BS1362. -
Page 7: Safety Symbols
SAFETY SYMBOLS The full technical specification of the battery charger is printed on a label on the charger. The meanings of the markings and symbols are shown below. Class II appliance which does not need an earth connection For indoor use only Read the manual before operating this machine Falls under the Waste Electrical &... -
Page 8: Battery Charging
BATTERY CHARGING 1. The new battery pack will require charging before use. 2. Squeeze the battery release buttons on either side of the battery pack and pull gently down to disengage the battery pack from the machine as in Fig 1. 3. -
Page 9: Initial Battery Charging
Minimum 4°C /Maximum 50°C. Avoid placing batteries in direct strong sunlight or other heat source. NOTE: Ni-Cad batteries as used in Clarke cordless power tools should be given a full charge when first supplied new. Maximum battery performance will be achieved after approximately 5 complete charge/discharge cycles. - Page 10 Note: As the battery becomes discharged, the power available will drop. Operating the machine at low speed will cause a reduction in torque. 6. After use, recharge the battery pack as shown on pages 8-9. Avoid leaving your batteries in a discharged state. LOOSENING A WHEEL NUT 1.
-
Page 11: Recharging
Keep the unit clean by wiping with a dry cloth. DO NOT use solvents as a cleaning agent. Your Clarke Impact Wrench has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local Clarke dealer. -
Page 12: Parts List And Diagram
SPARES & SERVICE CONTACTS For parts & servicing, please contact your nearest dealer, or CLARKE International, on one of the following numbers. PARTS & SERVICE TEL: 020 8988 7400 PARTS & SERVICE FAX: 020 8558 3622 e-mail as follows: PARTS: Parts@clarkeinternational.com... - Page 13 PARTS DIAGRAM...
-
Page 14: Technical Specifications
TECHNICAL SPECIFICATION r t r Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. ACCESSORIES A wide range of accessories is available from your nearest CLARKE dealer, for further information, contact your nearest dealer, or telephone CLARKE International Sales department on 01992 565300. -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY...
Need help?
Do you have a question about the CIR450 and is the answer not in the manual?
Questions and answers