Related Manuals for Clarke CIWLI300
Summary of Contents for Clarke CIWLI300
- Page 1 CORDLESS IMPACT WRENCH MODEL NO: CIWLI300 PART NO: 6487070 OPERATING & MAINTENANCE INSTRUCTIONS GC0716...
-
Page 2: Environmental Protection
INTRODUCTION Thank you for purchasing this CLARKE Impact Wrench. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Safety Precautions
SAFETY PRECAUTIONS WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Do not wear loose clothing or jewellery. Tie long hair out of the way. 3. Keep children and visitors away - do not let children handle the wrench. 4. -
Page 4: Impact Wrench Safety Instructions
13. NEVER attempt any repairs yourself. If you have a problem with this product contact your local CLARKE dealer. 14. ALWAYS use an approved cable extension suitable for the power rating of the battery charger (see specifications), the conductor size should also be at least the same size or larger than that on the charger. -
Page 5: Safety Symbols
6. Never crush, puncture, short external contacts or dispose of in fire or water. 7. Never attempt recharging the battery by means of an engine generator or a DC power source. 8. Never attempt to disassemble the battery. 9. Never allow a leaking battery to contact your person. If you come into contact with battery liquid take the following immediate action: •... -
Page 6: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. The battery charger for this product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. -
Page 7: Component Inventory
COMPONENT INVENTORY Upon receipt, unpack and lay out the components, checking against the following list. Any damage or deficiency should be reported to your Clarke dealer immediately. 1. 12V Impact Wrench with battery pack 2. Battery-charging unit 3. Spare battery pack 4. -
Page 8: Battery Charging
BATTERY CHARGING The battery will have been shipped in a low charge state and will require charg- ing before use. 1. Squeeze the battery release clips on either side of the battery pack and pull gently down to disengage the battery pack from the wrench as in Fig 1. -
Page 9: Operation
OPERATION CAUTION: MAKE SURE THAT THE WRENCH IS FULLY OFF BEFORE ATTACHING OR REMOVING A SOCKET. ALWAYS TAKE CARE TO USE THE CORRECT SIZE SOCKET FOR BOLTS AND NUTS. AN INCORRECT SOCKET WILL CAUSE DAMAGE TO THE BOLT OR NUT. FITTING A SOCKET 1. -
Page 10: Tightening A Nut
WARNING: ENSURE THAT THE CORRECT SOCKET IS BEING USED FOR THE NUTS ON YOUR PARTICULAR VEHICLE. AN INCORRECT SOCKET SIZE IS LIKELY TO DAMAGE THE HEADS OF THE BOLTS/NUTS. NOTE: As the battery becomes discharged, the power available will drop. 3. -
Page 11: Maintenance
Keep the unit clean by wiping with a dry cloth. DO NOT use solvents as a cleaning agent. Your Clarke impact wrench has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local Clarke dealer. -
Page 12: Component Parts List
COMPONENT PARTS LIST Description No Description Rubber Cap Spring Locking Ring Screw Circlip18 mm Gear Ring Washer Planetary Gear Screw Washer Aluminium Front Housing Screw Steel Bush Shaft Gear Washer Gearbox Cover T-Spindle Motor Washer Moving Pawl Motor Screw LED lamp Magnet/cover/tube &... -
Page 13: Component Parts
COMPONENT PARTS Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Specifications
1.5 m/s Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...