Related Manuals for DeVilbiss COMPACT COM-G430-16
Summary of Contents for DeVilbiss COMPACT COM-G430-16
- Page 1 SB-E-2-534 ISS.06 Operation Manual Advanced - Conventional Gravity Feed Spraygun P 1 – 12...
-
Page 2: Ec Declaration Of Conformity
If there is any doubt regarding the suitability of a specific material contact your local Distributor or ITW Finishing direct. Model Part Number COM-G430-16 Example: Aircap Fluid Nozzle size (14 = 1.4 mm) -
Page 3: Safety Warnings
SAFETY WARNINGS Fire and explosion Solvents and coating materials can be highly flammable or combustible when sprayed. ALWAYS refer to the coating material suppliers instructions and COSHH sheets before using this equipment. Users must comply with all local and national codes of practice and insurance company requirements governing ventilation, fire precautions, operation and house-keeping of working areas. -
Page 4: Parts List
Parts List Ref. Description Part Number Options Air Cap/Retaining ring See Selection Chart Nozzle See Selection Chart Separator SP-626-K5 Packing GTI-445-K2 Spreader Valve SP-403-K Stud and Screw GTI-408-K5 Needle Adjusting Screw SP-614-K Spring SP-622-K5 Needle See Selection Chart Airvalve housing + seal SP-612-K Spindle Trigger... - Page 5 CHART : AIR CAPS / NOZZLES AND NEEDLE COMBINATIONS AIR CAP/ RETAINING RING SP-100-***- K e.g *** = 430 CONVENTIONAL HVLP TRANS -TECH 430,497,443, 510,522,523,513, Nozzle SP-200S-**-K 085,10,12,13,14, 085,10,12,13,14, 085,10,12,13, e.g ** =14 =1.4mm 16,18,20,22 16,18,20,22 14,16,18,20,22 Needle SP-300S-**-K 085,10,12,13,14,16, 085,10,12,13, 085,10,12,13, 05,07,10...
-
Page 6: Specification
Specification Air supply connection - Universal “ BSP and NPS Maximum static Air inlet pressure - = 12 bar (175 psi) Nominal gun Air inlet pressure - 3 bar (44 psi) with gun triggered Maximum Service temperature 40°C Gun Weight - 583 g Materials of Construction Gun body... -
Page 7: Installation
Installation Important: To ensure that this equipment reaches you in first class condition, protective coatings have been used. Flush the equipment through with a suitable solvent before use. 1. Attach air hose to connector (13). Recommended hose size 8 mm bore. The hose must be conductive and electrical bond from the spraygun to earth should be checked with an ohmeter. -
Page 8: Replacement Of Parts
Replacement of Parts Nozzle (2) and Needle (9) – Remove parts in the following order: 7, 8, 9, 1 and 2. Replace any worn or damaged parts and re-assemble in reverse order. Recommended tightening torque for nozzle (2) 9.5-12 Nm (80-100 lbf in). Packing –... - Page 9 © 2003 ITW Finishing Systems and Products...
- Page 10 © 2003 ITW Finishing Systems and Products...
- Page 11 © 2003 ITW Finishing Systems and Products...
- Page 12 Accessories Spanner – order SPN-5 Cleaning Brush – order 4900-5-1-K3 Regulator/Gauge Attachment - order HAV-501-B or DGI-501-BAR Pressure gauge Attachment – order GA-515 Gun Mounted Regulator – order DVR-501 Spraygun Lubricant - order GL-1-K10 ITW Finishing Systems and Products ITW Automotive Finishing UK Ringwood Road, Anchorbrook Industrial Estate Bournemouth,...