Related Manuals for DeVilbiss Compact Series
Summary of Contents for DeVilbiss Compact Series
- Page 1 SB-E-2-530 ISS.04 Operation Manual HVLP and Trans-Tech Pressure Feed ® Spraygun P 1 - 12...
-
Page 2: Ec Declaration Of Conformity
Important: : These Sprayguns are suitable for use with both waterbased and solvent based coating materials. The design uses EPA compliant (Devilbiss Trans-Tech®) and HVLP atomising technology to reduce overspray and improve coating efficiency. These guns are not designed for use with highly corrosive and/or abrasive materials and if used with such materials it must be expected that the need for cleaning and/or replacement of parts will be increased. -
Page 3: Personal Protective Equipment
SAFETY WARNINGS Always wear eye protection when Fire and explosion spraying or cleaning the spraygun Solvents and coating materials Gloves must worn when can be highly flammable or spraying cleaning combustible when sprayed. ALWAYS equipment refer to the coating material suppliers Training –... -
Page 4: Parts List
Parts List Ref. No Description Part Number Options Air Cap/Retaining ring SP-100-***-K 522, 510, 505,523 COM-522 or COM-510 e.g *** = 522 Nozzle SP-200S-**-K 085,10,11,12,13,14, 16,18,20,22 e.g ** =14 =1.4 mm Separator SP-623-K5 Packing GTI-445-K2 Spreader Valve SP-401-K Stud and Screw GTI-408-K5 Needle Adjusting Screw SP-614-K... -
Page 5: Specification
Patent No 2372465 (GB) Specification Air supply connection - Universal “ BSP and NPS Fluid Supply Connection - Universal “ BSP and NPS Maximum static Air inlet pressure - = 12 bar (175 psi) Maximum static Fluid inlet pressure - = 15 bar (218 psi) Nominal gun Air inlet pressure - 2.5 bar (36 psi) 523 Trans-Tech Air Cap... -
Page 6: Installation
Installation Important: To ensure that this bore. The hose must be conductive equipment reaches you in first class and electrical bond from the condition, protective coatings have spraygun to earth should be been used. Flush equipment checked with an ohmeter. A through with a suitable solvent resistance of less than 10 Ohms is... -
Page 7: Replacement Of Parts
Replacement of Parts Nozzle (2) and Needle (9) – Remove Groove must face outwards. parts in the following order: 7, 8, 9, 1 12. Fit Valve Seat to Gunbody. and 2. Replace any worn or damaged 13. Remove Rear Airvalve Seal from parts and re-assemble in reverse order. - Page 8 © 2003 ITW Finishing Systems and Products...
- Page 9 © 2003 ITW Finishing Systems and Products...
- Page 10 © 2003 ITW Finishing Systems and Products...
- Page 11 Accessories Spanner – order SPN-5 Cleaning Brush – order 4900-5-1-K3 Regulator/Gauge Attachment - order HAV-501-B Pressure gauge Attachment – order GA-515 Gun Mounted Regulator – order DVR-501 Spraygun Lubricant - order GL-1-K10 Roundspray Aircap - COM-500R HVLP Mode - Air Inlet Pressure = 1.0 Bar (14.5 PSI) Tans-tech Mode –...
- Page 12 ITW Finishing Systems and Products Ringwood Road, Bournemouth, BH11 9LH, England. Tel. No. (01202) 571111 Telefax No. (01202) 581940, Website address http://www.itweuropeanfinishing.com ITW Oberflächentechnik GmbH & Co. KG Justus-von-Liebig-Straße 31 63128 Dietzenbach Tel (060 74) 403-1 Telefax: (060 74) 403300 Website address http://www.itw-finishing.de ITW Surfaces Et Finitions 163-171 avenue des Auréats B.P.
Need help?
Do you have a question about the Compact Series and is the answer not in the manual?
Questions and answers