Convenient Functions - Kenwood VRS-7100 Instruction Manual

Convenient functions

You can make further adjustments to the sound while listening to
playback in the surround mode.
÷ The mode using Sound key is defeated when the REC MODE is
ON. ¤
MULTI CONTROL % / fi / @ / #
ENTER
RCV Mode
Dimmer
Listen Mode5/ ∞
Adjusting the sound
1 Press the RCV Mode key on the remote control unit to set
it to the receiver control mode.
2 Press the Sound key
3 Press MULTI CONTROL @ / # (or the Multi@ / # key) to
select the setting item and press ENTER (or the Enter key).
Note that some items are not displayed in certain modes.
1 "SP LEVEL": *1
Adjusting the volume level of each channel
2 "INPUT": (Analog mode only)
Input level adjustment
3 "TONE": *2
Tone level adjustment
4 "EFFECT": (DSP mode only)
DSP effect leve adjustment
5 "DUAL MONO": *3
Selection between Stereo, Main audio, Sub audio and
Main + Sub audio
6 "MIDNIGHT": *4
Midnight mode adjustment
7 "PANORAMA": *5
Panorama mode ON/OFF
8 "DIMENSION": *5
Dimension adjustment
9 "C WIDTH": *5
Center width adjustment
0 "C IMAGE": *6
Center image mode adjustment
*1 The setting in the SOUND mode is temporary. It returns automati-
cally to the original level set in "Speaker settings" when the
receiver is turned OFF/ON.
*2 PCM stereo and analog stereo mode only.
*3 DOLBY DIGITAL mode only
*4 DOLBY DIGITAL, DTS mode only
*5 Only when the input signal is a 2-channel signal in the DOLBY PRO
LOGIC IIx MUSIC or DOLBY PRO LOGIC II MUSIC mode.
*6 Only when the input signal is a 2-channel signal in the DTS
NEO:6 MUSIC mode.
4 Use the MULTI CONTROL % / fi (or the Multi % / fi) to
adjust the setting as desired.
÷ The adjustment item is displayed for approximately 20 seconds.
5 Press the Sound key again to return to the input indication.
42 EN
LISTEN MODE
Multi % / fi / @ / #
Enter
Sleep
Sound
Stereo
•
º
e
r
e
e
e
r
Adjusting the volume level of each channel
The volume levels of the center speaker, subwoofer, surround speaker
and surround back speaker channels can be adjusted during playback.
1 Press the RCV Mode key on the remote control unit to set
it to the receiver control mode.
2 Press the Sound key
3 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select "SP LEVEL" on setup displays, and press the
ENTER (or Enter key).
4 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select the speaker.
1 Subwoofer level adjustment ("SW" indicator blinks)
2 Center speaker level adjustment ("C" indicator blinks)
3 Surround speaker level adjustment ("LS", "RS" indicator
blinks)
4 Surround back speaker level adjustment ("LB", "RB" or
"BS" indicator blinks)
5 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to adjust the speaker volume level.
+ 1
÷ The level of each speaker channel can be adjusted in 1 dB
steps between -10 dB and +10 dB.
6 Repeat steps 4 and 5 as required.
7 Press the Sound key again to return to the input indication.
÷ The setting in the SOUND mode is temporary. It returns automati-
cally to the original level set in "Speaker settings" when the
receiver is turned OFF/ON.
Adjusting the DSP effect level
The DSP effect level can be adjusted when the listen mode is a DSP surround
mode "ARENA", "JAZZ CLUB", "THEATER", "STADIUM" or "DISCO".
1 Press the RCV Mode key on the remote control unit to set
it to the receiver control mode.
2 Press the Sound key
3 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select "EFFECT" on setup displays, and press the
ENTER (or Enter key).
4 Use the MULTI CONTROL % / fi (or the Multi % / fi) to
adjust the EFECT LEVEL.
E F
÷ The DSP effect level can be adjusted in the range between 1 and 5.
5 Press the Sound key again to return to the input indication.
) / + 1 ) d
(DSP mode only)
F E C T
B
3