Download  Print this page

Checking The Codes; Re-Assigning Device Keys; Operating Other Components; Clearing All Of The Settings Registered Or Stored In The Remote Control Unit - Kenwood VRS-7100 Instruction Manual

Audio video surround receiver
Hide thumbs

Advertisement

Basic remote control operations for other components

Checking the codes

The 4-digit setup codes registered in the input selector keys can be
checked as follows.
1
Press the input selector key in which the setup code of the
desired component is registered.
2
Press and hold the Remote Setup key until the LED blinks
twice, then release the Remote Setup key.
÷ Proceed to the next steps in less than 10 seconds after the LED
blinks twice.
3
Press the numeric key to enter "9 9 0".
÷ The LED will blink twice.
4
Press the numeric key "1" once.
The LED blinks for the same number of times as the numeral in the
first digit of the 4-digit code. When the registered setup code is
"1338", for example, the LED will blink once. If a code digit is "0", the
LED will not blink.
5
Repeat step 4 three more times for the remaining digit.
Use "2" for the second digit, "3" for the third digit, and "4"
for the fourth digit.

Re-assigning device keys

The type of component device that can be registered is assigned in
advance in each input selector key, but this assignment can be changed
as desired by the user.
For example, the initial status is set so that a VCR can be registered in the
input selector VID1 key. If you want to register the setup code of a DVD
player in the VID1 key just like in the DVD key, reassign the key (change
the registerable component type assignment for the input selector key)
as described below.
1
Press and hold the Remote Setup key until the LED blinks
twice, then release the Remote Setup key.
÷ Proceed to the next steps in less than 10 seconds after the LED
blinks twice.
2
Press the numeric key to enter "9 9 2".
÷ The LED will blink twice.
3
Press the DVD key once, then press the VID1 key once.
The LED blinks twice, and it is possible to register the setup code
of a DVD player in the VID1 key just like in the DVD key. Now
register the setup code according to the model of the DVD player.
The combination of components assignable to the input selector
keys can be changed by pressing different keys in step 3. For
example, to change the key assignment so that the same compo-
nent as that registered in input selector "B" key can be registered
in input selector "A" key, press the "B" key then the "A" key after
entering "9 9 2" with the numeric keys.
÷ For the originally assigned relationship between the input selector keys
and system component types, see the table on the previous page.
÷ To restore the original component type assignment of an input
selector key, press that input selector key twice after entering "9 9 2".
÷ It is not possible to register a component in the TUNER key.
Examples of key re-assignment and the order of pressing the keys:
Registration of a DVD player in the VID1 key
To change the VID1 key to another DVD:
"9 9 2" \ "DVD" \ "VID1"
Restoration of the original key assignment
To return the VID1 key to the VID1 key:
"9 9 2" \ "VID1" \ "VID1"
Registration of a VCR in the VID2 key
To change the VID2 key to another VCR:
"9 9 2" \ "VID1" \ "VID2"
Restoration of the original key assignment
To return the VID2 key to the VID2 key:
"9 9 2" \ "VID2" \ "VID2"
46
EN

Operating other components

This operation lets you operate the registered components.
Input selector keys
SRC Power
1
Use the Input Selecter keys to select the component you desire.
When the input selector key is pressed, the system component
registered in the pressed key becomes ready to be controlled. The input
selector of the receiver is also switched accordingly. If you want to
control the component registered in the remote's input selector key
without switching the receiver's input selector to that source, press and
hold the input selector key for more than 3 seconds.
÷ To put the remote control unit to the receiver control mode, press
the RCV Mode key.
2
Turn the component ON.
÷ A DVD player, CD player, MD recorder or VCR registered in one of the
remote's input selector keys can be turned ON by pressing the
remote's SRC Power.
÷ A TV registered in one of the remote's input selector keys can be
turned ON by pressing the remote's TV Power key.
3
Press the operation keys you desire.
÷ For the keys that can be used with each system component, see
pages 58 to 59.
Clearing all of the settings registered or
stored in the remote control unit
You can reset the remote control unit to the initial status after purchase,
clearing all of the component registration using setup codes and other
data stored using the learning functions.
1
Press and hold the Remote Setup key until the LED blinks
twice, then release the Remote Setup key.
÷ Proceed to the next steps in less than 10 seconds after the LED
blinks twice.
2
Press the numeric key to enter "9 8 1".
÷ The LED blinks four times, and all of the data you registered
or stored in the remote control unit is cleared.

Advertisement

Table of Contents
loading

  Also See for Kenwood VRS-7100

  Related Manuals for Kenwood VRS-7100