POSIFLEX XP-2000 Series User Manual

POSIFLEX XP-2000 Series User Manual

Fan free touch terminal

Advertisement

XP-2000 Series
Fan Free Touch Terminal
User's Manual
Rev.: Original
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause interference to radio communications.
It has been tested and found to comply with limits for a Class A digital device pursuant to subpart
J of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be
required to take whatever measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized technicians opens
the machine. The user should consult his/her dealer for the problem happened. Warranty voids if
the user does not follow the instructions in application of this merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex
Technology, Inc. will assume no liability for any technical inaccuracies or editorial or other errors
or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise
damages, including without limitation loss of data or profits, resulting from the furnishing,
performance, or use of this material.
This information is provided "as is" and Posiflex Technology, Inc. expressly disclaims any
warranties, expressed, implied or statutory, including without limitation implied warranties of
merchantability or fitness for particular purpose, good title and against infringement.
The information in this manual contains only essential hardware concerns for general user and is
subject to change without notice. Posiflex Technology, Inc. reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide applicative
notices and arrangement for special options utilizing this product. The user may find the most up
to date information of the hardware from: http://www.posiflex.com or http://www.posiflex.com.tw
or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage peripheral.
Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this
or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
or otherwise, without prior express written consent from Posiflex Technology, Inc. the publisher of
this documentation.
© Copyright Posiflex Technology, Inc. 2009
All brand and product names and trademarks are the property of their respective holders.
P/N: 1 5 4 6 0 9 0 0 0 1 0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XP-2000 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for POSIFLEX XP-2000 Series

  • Page 1 All data should be backed-up prior to the installation of any drive unit or storage peripheral. Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this or any other Posiflex product.
  • Page 2: About This Product

    You may apply ammonia-based glass cleaner only on the screen surface. ABOUT THIS PRODUCT Posiflex XP-2000 series presents a whole new generation POS terminal, which is a combination of touch screen, printer, MSR, and the most reliable FanFree structure. This integrated solution of XP-2000 series not only less cable connection, but also carrying a brilliant performance to user in order to face the busiest situation.
  • Page 3: Product Pictures

    INTRODUCTION PRODUCT PICTURES Front Views Side Views Rear & Bottom Views Page 2...
  • Page 4: Parts Identification

    PARTS IDENTIFICATION LCD display with or without touch panel Printed paper exit LED indicator for power and printer status Paper feed button Power switch Magnetic Stripe Reader(Option) Base Stand LCD adjustable Holder Lock/Release button for tilt angle adjust 10. Printer cover 11.
  • Page 5 TOUCH SENSOR 5 Wire Touch Pad Storage device DOM (Optional SSD HDD or SATA HDD) Power switch On the front bezel Power saving Suspension mode Power supply power adaptor, 60W Indicator LED and Power ON/ standby, Printer Error /Paper Out (RED), Control panel switch paper feed and power ON switch.
  • Page 6 INSTALLATION GUIDES Hardware Power Switch and printer paper feed The power switch located in the front bezel of main unit. It is a pushbutton switch and controls the power on/off of the system. Also, next to the power switch is the paper feed button for integrated printer.
  • Page 7: Display Issues

    Posiflex USB Touch Manager A program named “Posiflex USB Touch Manager” and a right-click sticky button tool in the program group “Posiflex USB Touch Tools” is installed in the preloaded Windows system with a USB interface touch panel controller. This program can also be obtained by download from the POSIFLEX web site.
  • Page 8: Printer Operation

    Printer Operation In the left side of XP-2000 series’ main unit, there is a 2” printer integrated. For XP-2007/2008, it built-in printer with manual cutter and could be option an auto- cutter.
  • Page 9 Self Test For XP-2000 series printer’s test mode, please turn off the terminal first. After the system power off, please press and hold down the feed button while turning on the system power switch.
  • Page 10 Printer setup There are two difference way to setup XP-2000’s printer. Firstly, one is the DIP Switch inside of terminal for setup the function such as baud rate, Full-cut mode and others. Another switch is setup trough software to adjust not only the hardware switch function but also add printer density and others.
  • Page 11 The MSR in XP-2000 series reads the ISO or JIS-II magnetic stripe card without driver. Yet, there is a “Posiflex USB MSR Manager” program provided to control some parameter configuration for ISO MSR.
  • Page 12 I/O plate. It can supply a +5 V DC through pin 9 of serial port and +12V DC through VGA port after jumper setting. However, except Posiflex peripheral device, do not connect any other device to this port before the power in this port is disabled.
  • Page 13: Preparing The Main Unit

    Please consult your dealer for technical support on setup of these jumpers. Please notice that only those qualified technicians may adjust in the service window with information from Posiflex and the contents in the service window may change without notice as time develops.
  • Page 14 Rear Mount Upgrade Kit There are plenty of upgrade kits of XP-2000 series for choice. To install these upgrade kits, please refer the installation guide of each kit. For some interface such as serial ports and VGA ports, please remember to enable the power supply of the main unit for the upgrade kit if the serial or VGA interface model is used.
  • Page 15: System Recovery

    System Recovery For XP systems preloaded with Windows WEPOS / POS Ready / Windows CE / Linux on DOM, HDD or Solid State Drive, Posiflex provides recovery DVD delivered with the terminal for the preloaded operating system. The System Integrator shall take care of software restoration after OS recovered.
  • Page 16: Operating System Installation

    “\drivers” in OS recovered HDD and the latest versions of these required drivers will be available on our web: http://www.posiflex.com. Then follow instructions from your system integrator for software recovery.
  • Page 17: Power Supply

    This device can be replaced with an option SSD HDD or 2.5” SATA HDD. TECHNICAL MANEUVERS Some technical maneuver in XP-2000 series such as serial COM port +5V power supply settings is supported in system jumper setting. However, such support is limited to the application of specific Posiflex peripherals and must be disabled when the Posiflex peripherals are disconnected.
  • Page 18 Manual from Posiflex or consultation from Posiflex authorized dealers and should be handled only by a qualified technician. T31454 警 告 使 用 者 警 告 使 用 者 警 告 使 用 者 警 告 使 用 者 這 是 甲 類 的 資 訊 產 品 , 在 居 住 的 環...

Table of Contents