POSIFLEX XT– 3015 User Manual

POSIFLEX XT– 3015 User Manual

Fanfree lcd touch terminal

Advertisement

XT– 3015
Fanfree LCD Touch Terminal
User's Manual
Rev.: Original
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex Technology, Inc. will assume no liability for any technical inaccuracies or
editorial or other errors or omissions contained herein, nor for direct, indirect,
incidental, consequential or otherwise damages, including without limitation loss of
data or profits, resulting from the furnishing, performance, or use of this material.
This information is provided "as is" and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technology, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technology, Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2013
P/N: 16640900010
All brand and product names and trademarks are the property of their respective holders.
Part 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XT– 3015 and is the answer not in the manual?

Questions and answers

Summary of Contents for POSIFLEX XT– 3015

  • Page 1 About This Manual: Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex Technology, Inc. will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including without limitation loss of data or profits, resulting from the furnishing, performance, or use of this material.
  • Page 2 ALERT TO OUR HONORABLE CUSTOMERS: Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. This product contains inside a Lithium battery. Please always follow local environmental protection laws / regulations for disposal of used batteries and always replace only with battery of same type.
  • Page 3 INTRODUCTION PRODUCT PICTURES FOR Gen 7&8 BASE STAND Gen 7 Base Front View Rear View Gen 8 Base Front View Rear View Side View Inside touch open door Part 3...
  • Page 4: Parts Identification

    Base Stand and Bottom View Gen 7 Base Gen 8 Base PARTS IDENTIFICATION Main Unit LCD touch panel Power indicator Gen 7 ,8 base stand Hinge for LCD terminal HDD cover Power switch Brightness adjust push button “+” Brightness adjust push button “-” 10.
  • Page 5: Product Features

    13. Compression lock for base stand cover 14. Bottom plate 15. Rubber feet with bottom plate fixing screw 16. 2 HDD cover 17. Base cover PRODUCT FEATURES Standard Features: CPU: Intel Pine View D525 1.8G CPU, 1M Cache, Dual core . a ) a ) a ) a ) Fan free structure with Aluminum die-cast main unit casing.
  • Page 6: Opening Cable Cover

    11. One 4 pin connector for optional UPS battery in Gen 8 base only. Dual display support (per OS capability). m ) m ) m ) m ) VGA memory support DVMT 4.0. n ) n ) n ) n ) Support high performance DDR3 SDRAM with maximum memory o ) o ) o ) o ) size 4GB in one SODIMM.
  • Page 7 DISCONNECTING ALL CABLES After removal of the cable cover, the connector area will be accessible then. Please first note orientations of every existing cable connection and then disconnect every cable properly before separating the main unit from the adjustable stand assembly. Please note that the click lock spring has to be pressed down prior to pulling out the connector such as the LAN port or the CR port or the alternate RJ45 form COM3/4 port.
  • Page 8: Base Mount Upgrade Kit

    BASE MOUNT UPGRADE KIT Please follow the instructions on the manual that comes along with the customer display LM-3010/LM-3014/LM-3015, and PD-6307 if installed. For Second LCD Display There are LM-3010/LM-3014/LM-3015 available for 2 LCD display, needed to combine with XT3015 with supporting bracket to tighten.
  • Page 9 The RJ11 connector in I/O area of a XT-3015 system can be used for controlling most of the common cash drawers available on the market. However, it is most recommended to use Posiflex CR-2200 or CR-2210 or CR-3100 or CR-4000 or CR-4100 or CR-6300 for best compliance to operate the opening mechanism and to monitor the drawer open status.
  • Page 10: Connecting Cables

    OS could be a major difficulty for average user or obstacle by possibly unintentional negligence even for PC veterans to accomplish such a task. Therefore, OS installation into a system without preloaded OS is highly discouraged. Posiflex Technology, Inc. shall Part 10...
  • Page 11: Application Environment

    not be responsible for any technical support to questions on this aspect. APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit at ALL times for the installation.
  • Page 12 When using this feature, please make sure that the software application has the ability to power off the machine. In preloaded Windows, “Posiflex Power Switch Manager” in “Posiflex Tools” in the Program Files helps managing these functions.
  • Page 13: Brightness Control

    The VGA port in the XT-3015 system supports either a separately connected LCD monitor or touch monitor. To support the DC power to the Posiflex LCD display, have a qualified technician to set the power supply in XT main unit through the VGA connector according to Posiflex technical information.
  • Page 14: Parallel Port

    Manager is already installed on your system. Nevertheless, you can also download the Manager from our website: Visit us at http://www.posiflex.com, and click Support on the main menu bar. On Support page, click Download on the left to access Download page.

This manual is also suitable for:

Xt-3015

Table of Contents