Download Print this page
POSIFLEX XT-8315 User Manual

POSIFLEX XT-8315 User Manual

Fanless pos terminal

Advertisement

Quick Links

XT-8315/8315E
Fanless POS Terminal
User Manual
Package Contents
15" P-CAP touch terminal with Gen 7E or Gen 8E base.................(x1)
Power adapter....................................................................(x1)
Power cord......................................................................(x1)
FCC NOTES
This system meets industry & government requirements and applicable standards. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A digital
device pursuant to subpart B of Part 15 of FCC Rules, which are designed to provide
reasonable protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever measures to correct the
interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement résidentiel,
cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise.
The manufacturer is by no means responsible for any damage or hazard caused by improper
application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne autre
que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le problème qui
se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions d'application de
cette marchandise. Le fabricant n'est en aucun cas responsable de tout dommage ou danger
causé par une mauvaise application.
XT-8315/8315E Ver. B0
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the XT-8315 and is the answer not in the manual?

Questions and answers

Summary of Contents for POSIFLEX XT-8315

  • Page 1 L'utilisateur doit consulter son revendeur pour le problème qui se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions d'application de cette marchandise. Le fabricant n'est en aucun cas responsable de tout dommage ou danger causé par une mauvaise application. XT-8315/8315E Ver. B0...
  • Page 2 Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez la batterie usagée conformément aux réglementations locales en matière d'élimination. 警告 本電池如果更換不正確會有爆炸的危險,請依製造商說明書處理用過之電池。 Views of XT-8315/8315E with Gen 7E Base Front View P-CAP Touch Panel Gen 7E Base LED indicator...
  • Page 3 Rear View Neck Cover Cable Cover Cable Exit Side View Power Button Brightness Adjustment Button + Brightness Adjustment Button - Bottom View Rubber Feet with Fixing Screw Cable Exit Cable Holder Rubber Feet with Fixing Screw...
  • Page 4 Views of XT-8315/8315E with Gen 8E Base Front View P-CAP Touch Panel Gen 8E Base LED indicator Rear View Neck Cover Cable Cover Cable Exit Side View Power Button Brightness Adjustment Button + Brightness Adjustment Button -...
  • Page 5 Connector Positioning your POS for a Perfect Viewing Angle The adjustable bases designed for XT-8315/8315E come in two models, Gen 7E/8E, and allow you to determine an ideal position for your terminal by using its unique tilt adjustment mechanism. As the below figures suggest, both bases provide three standard positioning solutions for your terminal: Flat Folded mode, Low Profile mode, and Full Extended mode.
  • Page 6 Low Profile mode Full Extended mode In general, XT-8315/8315E will be set up beforehand in Flat Folded mode and then packaged into the box for shipping. After it is unpacked, you may re- adjust the terminal in either Low Profile mode or Full Extended mode according to your situation.
  • Page 7 Support the screen with one hand holding onto its bottom edge. Then, while pulling the lever backwards, move the display upwards until the lever is snapped into the lower hook to raise the screen as shown in the below figure. Lower hook Lever...
  • Page 8 Return your terminal back to Flat Folded mode from Full Extended mode. Remove the cable cover from the base. 4.2 Remove the two screws from the base. Remove the two screws. 4.3 Tilt your screen in a horizontal position. 4.4 Support the screen with one hand holding onto its bottom edge. While pulling the lever backwards, move the display downwards until the lever is lifted off the hook as shown in the figure.
  • Page 9 XT-8315/8315E with Gen 8E Base Please refer to the following instructions on how to switch among different positioning modes to find an ideal viewing angle for XT-8315/8315E with Gen 8E base. Unpack XT-8315/8315E, which is supposed...
  • Page 10 Position your terminal in Full Extended mode. Support the screen with one hand holding onto its bottom edge. Then, while pulling the lever backwards, move the display upwards until the lever is snapped into the lower hook to raise the screen as shown in the below figure.
  • Page 11 Position the terminal in Low Profile mode. While keeping your terminal steady with your hand holding on to the base, tilt your terminal down. Then, remove the cable cover from the base. Remove the two screws from the base. Remove the two screws. Support the screen with one hand holding onto its bottom edge.
  • Page 12 5.4 Push the cable cover back. 5.5 Tilt the screen up or down to your desired angle. Please do not press on the LCD panel while setting up the tilt angle. Return the terminal back to Flat Folded mode. While steadying your terminal with your hand holding onto the base, tilt your screen up.
  • Page 13 Routing and Arranging Cables Gen 7E/8E bases feature their own cable management to help you well organize the cords whenever you need to connect peripheral devices to XT-8315/8315E. The following provides some useful cable-routing instructions required to manage your cables.
  • Page 14 Tilt the terminal up enough to have the bottom I/O plate towards you. Locate the cable arrangement cover as shown in the figure. Cable Arrangement Cover Remove the cable arrangement cover by pushing it up in the direction shown by the arrow.
  • Page 15 Installing Optional Upgrade Kits and Peripherals XT-8315/8315E is an expandable model which allows you to upgrade its own capacity by additionally installing multiple peripheral devices, such as magnetic stripe reader (MSR), LCD monitor, and cash drawer, according to your preference. The following will give you installation instructions on how to expand on your current POS system with these optional upgrade kits.
  • Page 16 Take the AC power adapter with its rubber feet facing you. Place the bottom side of the power adapter into the bottom of the power adapter compartment first, and then push the top side of the adaptor into the compartment. After pushing the power adapter up to the top, place two brackets separately on the top and bottom sides of the power...
  • Page 17 Neatly thread the cord along the bottom edge of the PoweredUSB compartment (1), and then use the cable tie to hold the extra cable (2) as shown in the figure. Cable tie Place back the PoweredUSB Lay the POS terminal on a compartment bracket into flat surface with its rear place, and then secure it...
  • Page 18 Installing an Operating System You are highly advised not to install an operating system on XT-8315/8315E without professional instructions. Not only might the careless handling during installation cause irreversible damage to your machine, but also the improper...
  • Page 19: Operation Environment

    Operation Environment To prevent XT-8315/8315E from overheating, it is suggested to position your terminal in a well-ventilated working environment. In doing so, please be advised to keep the POS terminal at least 25mm away from other devices to ensure the machine is properly cooled down and functioning normally.
  • Page 20: Specifications

    0°C - 40°C, 20%RH - 90%RH Operating Condition -20°C - 70°C, 10%RH - 90%RH Storage ※ The product information and specifications are subject to change without prior notice. To get the detailed information on the XT-8315/8315E, please check this model from Posiflex Global Website.

This manual is also suitable for:

Xt-8315e