Fault Finding Chart; Environmental Information - Flymo Contour PowerPlus Original Instructions Manual

WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS CLATTER-
ING NOISE
LINE SNAPS CONTINU-
OUSLY
WHEEL STOPS TURNING
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
• Awareness of the environment must be considered
when disposing of ʻend-of-lifeʼ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indi-
cates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and elec-
tronic equipment.
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna UK Ltd., through its Au-
thorised Service Repairers will effect the repair or replacement to
the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjust-
ment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart
or tampered with by any person not authorised by Husqvarna
UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is impor-
tant that you read the instructions contained in this Operator's Man-
ual and understand how to operate and maintain your machine:

Fault Finding Chart

CHECK
Is the automatic line feed work-
ing?
Is the line fed out and visible?
Has line been removed from
cleat?
Is the manual line feed working?
Has the motor reached full
speed before use?
Has too much line been fed out?
Is the line cutter missing from the
safety guard?
Are you using the trimmer cor-
rectly?
Is the line jamming on the spool?
Clean wheel and groove on trimmer head. SEE "MAINTENANCE"
Contact Husqvarna UK Ltd. Customer Service
Telephone : 01325 300303

Environmental Information

Guarantee & Guarantee Policy
Manually feed out line.
No
SEE "MANUAL LINE FEED"
Remove cap and spool, free line
No
and re-fit spool and cap. SEE
"CUTTING HEAD"
The line may be jammed on the
spool. Rewind line to remove
No
crossed loops. Check that line is in
correct section of spool.
Allow the motor to reach full speed
No
before use.
Yes
SEE "MANUAL LINE FEED"
Contact your local approved
Yes
Service Centre or Husqvarna UK
Ltd. Customer Service.
Only use tip of nylon line to trim.
?
SEE "How to trim and edge"
Rewind the line on the spool, if
Yes
symptoms still persist, change
spool and line.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise
be caused by inappropriate waste handling of this prod-
uct.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where
you purchased the product.
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance
with the instructions and recommendations contained in this
Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts
and their life is dependent on regular maintenance and are,
therefore not normally subject to a valid warranty claim: Nylon
Line, Spool and Line, Electric Mains Cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the war-
ranty for defects caused in whole or part, directly or indirectly
by the fitting of replacement parts or additional parts that are
not either manufactured or approved by Husqvarna UK Ltd.,
or by the machine having been modified in any way.
ACTION