Fault Finding Chart; Replacement Parts; Environmental Information - Flymo Contour 500 XT Original Instructions Manual

WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS CLATTER-
ING NOISE
LINE SNAPS CONTINU-
OUSLY
WHEEL STOPS TURNING
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna UK Ltd., through its Authorised
Service Repairers will effect the repair or replacement to the cus-
tomer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment
by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart or
tampered with by any person not authorised by Husqvarna UK Ltd.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator's Manual
Spool and Line
Reference no.:
• Awareness of the environment must be considered when dis-
posing of 'end-of-life' product.
• If necessary, contact your local authority for disposal informa-
tion.
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recy-
cling of electrical and electronic equipment.

Fault Finding Chart

Is the automatic line feed work-
ing?
Is the line fed out and visible?
Has line been removed from
cleat?
Is the manual line feed working?
Has the motor reached full speed
before use?
Has too much line been fed out?
Is the line cutter missing from the
safety guard?
Are you using the trimmer cor-
rectly?
Is the line jamming on the spool?
Clean wheel and groove on trimmer head. SEE"MAINTENANCE"
Contact Husqvarna UK Ltd. Customer Service
Telephone : 0844 844 4558 UK
Guarantee & Guarantee Policy

Replacement Parts

FLY021

Environmental Information

CHECK
and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the
instructions and recommendations contained in this Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and
their life is dependent on regular maintenance and are, therefore
not normally subject to a valid warranty claim: Nylon Line, Spool
and Line, Electric Mains Cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the warranty
for defects caused in whole or part, directly or indirectly by the
fitting of replacement parts or additional parts that are not either
manufactured or approved by Husqvarna UK Ltd., or by the ma-
chine having been modified in any way.
Part no.:
By ensuring this product is disposed of correctly, you will help pre-
vent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate
waste handling of this product.
For more detailed information about recycling of this product,
please contact your local council office, your household waste dis-
posal service or the shop where you purchased the product.
ACTION
Manually feed out line.
No
SEE "MANUAL LINE FEED"
Remove cap and spool, free line
No
and re-fit spool and cap. SEE "CUT-
TING HEAD"
The line may be jammed on the
spool. Rewind line to remove
No
crossed loops. Check that line is in
correct section of spool.
Allow the motor to reach full speed
No
before use.
Yes
SEE "MANUAL LINE FEED"
Contact your local approved Serv-
Yes
ice Centre or Husqvarna UK Ltd.
Customer Service.
Only use tip of nylon line to trim.
?
SEE "How to trim and edge"
Rewind the line on the spool, if
Yes
symptoms still persist, change
spool and line.
1800 882 350 ROI
513937190